Complete Guide To Broadhead Tuning

The Ancient Longbow Legacy
8 followers
9 Video Views·Dec 15, 2025
If you clicked on this video, it's likely you've had problems getting your broadheads to fly with
your field points at some point, and I know just how frustrating it can be. I remember when I was
younger, I used to write on my fletchings of each arrow to mark which way the arrow would go when I
needed to take a shot, as some would hit high left, and some would hit low right, and everywhere in
between. Despite the adjustments I made or how I indexed my broadheads, I could never get them all
to fly just like my field points. It lowered my confidence as a bowhunter, and I knew I had to
figure out how to fix this. Technology and bows have improved a lot since then, but these problems
can still persist. I think it's flying so crooked. Truth be told, there's a lot more to getting your
broadheads to fly with your field points than simply moving your rest one direction or another.
There are many different factors that can affect this, but I'm not trying to confuse you or
overload you with information. I just want to put all of the factors out there and show you what to
do to fix it so that you can be as accurate as possible and the best bowhunter that you strive
to be, especially if you've struggled with this issue in the past, even if you've watched other
videos on it. The very first thing we need to do is synchronize our cams. Now, if you are shooting
any bow other than a single cam bow, it is very, very important that you get the synchronization
of your cams perfect. If the sink is off even just a little bit, even as much as just an eighth
of an inch, it will absolutely affect your vertical knock travel, and the arrow will either come out
knock high or knock low, and no amount of knocking point adjustment or rest adjustment will be able
to correct it and correct it for the arrow flight all the way downrange. If your arrow is not coming
out of your bow straight, not only will your broadheads not fly accurately and consistently,
but you will also suffer a lack of penetration because the arrow is not carrying that full
energy in a straight line all the way through your target. In order to set your cam sink,
you're going to need a bow press for this. If you do not have a bow press, go to your local archery
shop. Let them help you. Your cams must be in sync. There is no easy way around this. They
have to be perfect, or anything else you do when you're trying to broadhead tune will not matter.
Next, I want to talk about your arrow choice. Your arrow spine, your fletchings, and your
broadhead choice are all going to have an impact on how your arrow flies, regardless of how well
your bow is tuned. So, I just want to touch on a few things here just to give you some insight to
how your broadheads will fly given your arrow setup. First off, arrow spine is important when
it comes to broadhead tuning. Static arrow spine refers to how stiff or how weak the shaft is.
If your arrows are too stiff, it's generally not a problem for compound archers using a mechanical
release aid. However, if your arrows are too weak, the arrow flexes too much, which can result in
sporadic arrow flight with broadheads and just inconsistencies in general, regardless of how
well the bow itself is tuned. Generally speaking, when shooting broadheads, a weak arrow will impact
to the right of your field points for a right-handed archer, but moving your rest won't
necessarily fix it. The easiest way to determine this is to look at the arrow charts that your
arrow manufacturer puts out there on the back of the arrow boxes. Simply align the column with your
cut arrow length and your poundage range, and it will give you the spine that you should be shooting.
In all reality, this is just a starting point, but it will almost always work good enough for
just broadhead tuning as it won't give you an arrow shaft spine that is too weak. Keep in mind
your total point weight, your insert weight, and how aggressive or how hard your cams are,
are all going to have an impact on the dynamic spine or the reaction of the arrow spine when
you're shooting your arrow shaft. Now, most charts will compensate for this with certain adjustments
that you need to make, such as Eason. I believe if you have an additional 25 grains in the front,
they say to raise your poundage on the chart by three pounds per 25 grains, but this also has to
come into play with how fast your bow is shooting your arrow, because that is directly proportionate
to how hard it's pushing the back of the shaft, and that will affect how much that arrow is flexing
when it's coming out of the bow. To give you an example of Rachel's setup, she is shooting
approximately 45 pounds with a 27-inch arrow, and so if you look at the chart, she's right in
that 500 range, but could potentially be shooting a 400-spine arrow as well. Now, obviously the
400-spine arrow would be stiffer than the 500-spine arrow, which would be weaker and flex
more, but given her settings, looking at the charts, the 500-spine arrow, although weaker
than the 400, will be plenty adequate for her to use. So if we look at my arrow setup with this
bow, my arrow is 27 and a half inches, and I'm shooting about 80 pounds. I've got 50 grains of
brass in the insert, and I shoot a 100-grain point. So if I look at the chart, the Easton arrow chart,
it's going to tell me I need to add six pounds of draw weight for that additional 50 grains that
I've got in the front of my arrow, and that will lead me to the range of a 300-spine to a 260-spine
on the chart. So I choose to shoot an Easton Axis 300-spine, and it works perfectly fine for me with
this setup, but you could, of course, go to that 260-spine, which would be a little bit stiffer, and it
would work just fine and be just a slightly heavier arrow for you. Now, these charts don't get your
arrow spine perfect by any means, but it will get you close enough so that your broadheads can be
flying with your field points. I also want to mention that it's very important that the ends
of your arrows are cut square so that the nock and the broadhead fit flush on the ends of your shaft.
If the nock is bent or the broadhead has any kind of wobble, it can be extremely difficult to shoot
accurately with that arrow, especially when it comes to shooting at distance. So I do recommend
checking your arrows on an arrow spinner to make sure that your nock and your broadhead do not have
a wobble to them. One last short comment about arrows. I have personally found that indexing
your veins with your broadheads and spine alignment and the shaft is not as important as
it may be perceived, so you really don't need to worry about wasting your time on those specific
steps. Not that you can't do them. You can absolutely do them, and if that builds confidence,
that is great, but I've found it is not a necessary requirement to get my broadheads to fly extremely
accurate with my field points. Next, let's talk about fletchings and broadheads. There are no
hard and fast rules on this, but I just want to explain it in a way that is easy for everyone to
understand. Your fletchings serve as wings on the back of your arrow. These wings catch air and
catch drag and steer your arrow in a straight line towards your target. It's important to understand
it is not the length of the fletching that gives you the steering power from the back of your arrow.
It's actually the height or the distance that that fletching extends away from the shaft that
provides the steering power. This is why a standard 2-inch blazer vane can actually have
more steering power for your broadheads than a 3-inch vane that has a lower profile or lower
height away from the arrow shaft. Fletching helical can also play a big role in this, as it increases
the surface area that the air is catching, which will essentially increase its steering power. It
makes sense that we would want as much steering power as possible to steer our broadhead to
provide us the most accuracy downrange, but there are some drawbacks to having too much steering
power on your arrows. It's important to find the right mix. If our fletchings are too tall and
stick out too far away from the center of our arrow, this increases our likelihood to get
fletching contact on the rest, the cables, the cable guard, the bow, anything like that, which
can give us issues with arrow flight no matter how well your bow is tuned otherwise. Additionally,
the more steering power we have on our arrows, the more drag is induced on those arrows in flight,
especially as we get out in distance. Now, when there's a lot more drag on your arrows due to the
fletchings, this also creates noise in flight. When your arrows and fletchings have a combination
that provides a lot of steering power, you will notice a big difference in arrow noise, and it's
not always the bow noise that spooks animals and makes them duff. It's the arrow noise when that
arrow is coming towards them. It's important to find a good fletching and good fletching
combination for your setup so that you can achieve the optimal amount of steering where
you've got enough but aren't lacking with not enough to steer your broadheads. To keep this
simple, just make sure that your fletching combination has more steering power than your
broadhead. To quantify this in a simple sense, if you're shooting a big fixed blade broadhead,
I'm talking really big. Think a four fletch combination with some kind of helical with a
fletching height of at least a half an inch. Now, if you're going to be shooting a low profile fixed
blade or especially a low profile mechanical like a G5 Deadmeat or a Rage, less steering power could
be required. So you could get away with simply running a three fletch on a boning heat vane,
for example, with little to no helical if you chose to. I always like to err on the side of
more steering than less, but it's important that you do find that right combination for you.
There's a lot more factors that go into this, such as aero speed, aero weight, momentum, etc.,
but don't get too caught up in this. As long as your fletchings have enough steering power
to steer your broadheads, it will not be the cause of your inaccuracy downrange. Now again,
I always like to steer to stay on the side of having too much steering rather than not enough
to avoid any inconsistency issues all around, but don't overthink this. With all that said,
I see way too commonly arrows with extreme helicals on their fletchings, and it's just simply
put, not needed. A slight offset or slight helical is really all you need to get that proper steering
with the proper fletching. If you've made it to this point so far, you're on the right track.
The next portion I want to mention can actually save you time and be more beneficial if you put
this time in to tuning your bow before you even shoot broadheads, and that is paper tuning and
bear shaft tuning. Many may argue that one or the other is a waste of time, and it doesn't matter
for the end result, but sometimes bear shaft tuning or paper tuning can show you the differences and
the results that just shooting broadheads might not. It is indeed possible to get your broadheads
to fly with your field points and still not have your broadhead arrow flying straight out of your
bow. Sometimes paper tuning or bear shaft tuning can show you results that you might need to adjust
cam spacers or shift your cams when the broadheads might not, and simply just adjusting your rest can
be very frustrating when you're making those adjustments and you're not seeing the results
that you want. An example would be shooting through paper at three feet and getting a right tear,
but then backing up to 10 feet and shooting your arrow through paper and getting a left tear,
and what is happening is when you shoot that arrow initially, it is kicked tail right coming
out of the bow, but by the time you get back to 10 feet, those fletchings have corrected
and that arrow has fishtailed to the left hand side. Now from this, we know that we will make
the adjustment to the first tear, the tear at three feet, so that that arrow is not kicking
out to the right first, but if we're shooting broadheads, we're simply going to adjust based
on the broadhead flight and that could be misleading, whereas with the paper tuning,
we can see exactly what is going on because that arrow is fishtailing back and forth at those
different distances. Now if we only adjust our rest horizontally, we may not be getting the
results that we're looking for, so how do we determine if we need to adjust our cams, shimmer
cams left or right horizontally or adjust our rest left or right horizontally? Well ideally,
in a perfect world, we want to have a rest set up with our arrow at center shot for the manufacturer
of the bow that you're shooting and adjust the spacers based off of that. Now of course,
we can adjust the rest so that it is off center shot. I always like to say we tune the bow to how
it shoots, not how it looks or how it measures, so if it is slightly off of the perfect measurement
of center shot, that is completely okay as long as the arrow is flying straight. This is just a
general rule of thumb that I like to go off of. I like to keep it centered on the center shot
and adjust the cam spacers to adapt to it accordingly. Now the compound bow is a machine,
but you as the shooter are a part of that machine because you directly input how that machine
functions when you shoot it, so all of that to say it is important when you're doing the fine
tuning of your setup regardless if it is paper tuning, bear shaft tuning, or the final adjustments
with broadhead tuning, it's important that you as the archer are the one shooting it so that you can
tune it to how you shoot. I'm not going to go more in depth on this here as we have several other
videos on this specifically within our bow builds and our ultimate bow build master class, but
ultimately if you've got clean tears through paper at multiple distances and your bear shafts are
impacting with your field point arrows at 20 yards, your broadhead tuning should require very
minimal adjustments to get them flying accurately with your field points. Now that we have confirmed
our cams are in sync, we have the proper arrow spine selection and fletching combinations,
we have done our preliminary tuning with our paper tuning and bear shaft tuning, we are finally ready
to shoot our broadheads downrange. Now you can keep this simple, I just recommend going to 20
yards, make sure your sight is sighted in with your field points right on and what we're going
to do is shoot our field points into the target and shoot our broadheads and look for the variances
to make adjustments. Now at this point if you have followed all these steps, your arrow spine is
correct, you have enough steering power with your fletchings and you're not getting fletching contact,
your broadhead tipped arrows should at least group together in the same general direction.
If they're not and they're impacting multiple different directions around your field points,
it is likely that it is some kind of form or shooting issue typically within the grip or
sometimes extreme cases of extra facial pressure that is just not needed. If this is the case,
I highly recommend to please go back and watch some of our learn archery videos on our learn
archery playlist. I recommend watching the draw length video, the bow grip video, and the anchor
point videos for whatever it is of the style of release that you are using. This was my problem
many years ago when I first started shooting, so believe me when I say you're not alone on this.
Everybody typically goes through this at some point, but it is very important that you learn.
It's important that you fine-tune yourself before you go to work fine-tuning your equipment,
because if you have inconsistencies with your shot, it can be very, very, very difficult to
tune in general, let alone get your broadheads to fly consistently with your field points.
Now let's discuss what adjustments we need to make based off of where the broadheads are flying
relative to our field points. The goal of this is to get the string pushing the back of the arrow
straight forward in a straight line, so that arrow is guided straight forward to the target with no
inconsistencies or variables that will make that broadhead fly off from your field points.
If the broadheads are flying consistently off in one direction, this is a good thing,
because we can adjust it and fix it, but what is happening is the back of the arrow is being
pushed out of the bow at an angle that does not align with the front of the arrow shaft.
If the back of your arrow is kicked up, down, left, or right, a broadhead-tipped arrow is
basically going to steer that shaft in whatever direction it is that that arrow is angled towards,
and this is because the broadheads with the blades on the front of the shaft almost act as
fletchings, similar to the fletchings on the back of your shaft, and they will steer your arrow that
direction, whereas with a field point, the field point does not have those steering capabilities
that a broadhead does, and so the fletchings on the back of the arrow will correct that bad arrow
flight and compensate for it, which is why you can still shoot amazing groups with a bow that is not
even well-tuned with field points. So, if we shoot our broadheads and they're flying either high or
low of our field points, we will want to fix this first. If your broadheads are hitting high above
your field points, always double-check your cam sync first and then either lower your rest or
raise your knocking point slightly. If your broadheads are impacting lower than your field
points and your cams are in sync, raise your rest or slightly lower your knocking point.
Now, for horizontal adjustments, the direction that you make your adjustments can sometimes
be confusing or misleading based on where your center shot is currently positioned
and the type of arrow rest that you're using, but let me explain. If your broadheads impact
left of your field points, generally speaking, we would make a very slight rest adjustment
to the left or we would shim our cams to the right. Now, we would only shim our cams if
we had not done the paper tuning or bear shaft tuning process prior to this. As we make this
adjustment, it's important to assess the arrows and determine if the broadhead arrow is getting
closer to your field point arrow as you make the adjustments. Now, if you continue moving that rest
to the left and you keep getting your broadheads impacting left no matter how far you move it left
or how far you move it right, this is a good indication that your arrows are way too stiff
for your current setup that you're shooting. Now, if your broadheads are impacting to the right of
your field point arrows, either move your rest slightly to the right or shim your cams slightly
to the left. Now, only move your rest if you did the paper tuning or bear shaft tuning portion
before broadhead tuning as the rest adjustment should be all that you need. Now, if you're making
those adjustments, those rest adjustments, to the right and you keep not seeing a difference
if they're always spaced out the same distance apart from one another, typically this means that
your arrows are a little bit too weak for your setup. So, try turning your bow down by about
five pounds or so and shoot and see if the problem persists. You'll likely find that it will clear up
the issue. So, if you want to shoot that heavier poundage, you're going to need to shoot a stiffer
shaft or cut down your shaft or put less weight in the front of your arrow. Now, sometimes when we
make these arrow rest adjustments, we either get worse results or seemingly no change and this is
due to the dynamic arrow spine being way off or the center shot of your arrow rest already being
too far out of tune from center. Now, an example of this could be if you're a right-handed shooter
and your broadheads are impacting right and your rest is already moved inside of your center shot
close to your riser. If we continue to make rest adjustments to the right, we're seemingly going
to get worse results or potentially no change to the results. So, if this is you, move your rest
back to center shot, restart the process, and assess the results from there. If you're still
getting broadheads right and you did not paper shaft or paper tune or bear shaft tune, I recommend
doing that. If you did not, you are likely going to have to shim your cams to the left.
Now, as you go through this process and make the adjustments, you will adjust your sight
so that your pin hits on with your field points and with your broadheads at 20 yards and then 30
yards and 40 yards and however far it is that you decide to shoot. Note that on extreme distances,
fixed blade broadheads will begin to impact lower than your field points and this is not
always due to tune. It is typically due to drag from the field points itself or from the broadheads
itself. Just like a four-fletch arrow is going to have more drag than a three-fletch arrow and
impact lower at 100 yards, the same can be said about having a big fixed blade broadhead on the
front of your arrow. It will induce more drag and impact lower when you get out to these extreme
distances. Not that I am advocating in any way for anybody to take these far shots, but I just
want to explain it so that you fully understand. This brings me to my next point and that is not
all broadheads are the same. Simply put, a big fixed blade broadhead will just simply not fly
as accurate as a smaller diameter head or a mechanical. This is one of the reasons why
mechanicals are so popular because they are so forgiving in flight, but that does not mean that
you shouldn't tune your bow. It is still a necessity and it doesn't mean that mechanicals
are the end-all be-all or better for you based on your setup. As a bowhunter, you've always heard
that shot location is key and it is. The hidden advantage to using a mechanical broadhead is the
fact that they are so much more accurate and so much more forgiving in flight. Now, this is not a
push for mechanical broadheads as not everyone's setup has enough kinetic energy for my opinion
for them to use a mechanical broadhead in the first place, but if your setup has enough energy
to use them, it is likely in your advantage to do so. I won't touch on this more here as we have a
whole other video on real world broadhead testing linked in the description of this video. If you've
watched the video to this point and you've gone through all of the steps in the video, but you're
still having problems, it's likely one of these issues that's causing it. Now, it's our job as
bowhunters to be as proficient as possible so that we can make the most humane and ethical kill
possible when we're out bowhunting in the woods. The first most common issue is hand torque. Now,
this will give you broadhead flight inconsistency issues. This is the number one cause of irregular
broadhead flight when your broadheads are impacting left, right, high left, low right
on an inconsistent basis. It almost always leads back to the grip, where your hand is placed in
grip, how your skin is pulled, where you're setting it, where your pressures are. All of that
make a huge difference with how that arrow is coming out of your bow and ultimately where those
broadheads land. I'm not going to go into detail of how to grip your bow. We've got other videos on
that, but make sure you've verified your grip is perfect so that you're not running into issues
with hand torque. Probably the second most common, but not quite as common as hand torque that could
be giving you inconsistency issues is actually string pressure against your face. Now, this
really doesn't cause issues unless you're shooting a very high let off and you have a lot of string
pressure on your face. For that, string is burying into your cheek, you're fletching, you're pushed
up against your skin, and that string is pulled into your cheek really hard or on the side of your
nose. If it's just lightly on the tip or lightly on the side of your face, you're not going to have
issues from this at all. But if you are getting supreme, like super facial contact on the string,
it's definitely going to throw the back of that arrow off and cause inconsistent arrow flight
when shooting broadheads. The third one, if you're not torquing your bow with your grip with your
hand and if you're not getting string facial pressure, it could be that you're shooting too
weak of an arrow. When I say too weak, that arrow is flexing too much. Your bow is pushing too much
energy into the arrow for what the arrow can handle. When that arrow is flexing too much,
it causes those big fixed blade broadheads specifically to veer to one side, catch that
air going as it's flying, and veer to that direction. And typically with a weak arrow,
with a right-handed shooter, that shaft is going to impact to the right. So if you're consistently
getting right impacts, no matter what you do, you adjust the rest, you adjust the shims,
and you're still getting right impacts, it's likely your arrow is a little bit weak. But
weak shafts can also cause inconsistencies. I've noticed where weak shafts can sometimes
send arrows to the right, but also low, also high, and kind of give you mixed results as well.
The fourth issue, this cannot be overlooked, this is so simple, we covered it first thing,
it's cam sync. If you have any vertical broadhead flight issues, either impacting higher or lower,
you've got to make sure your cams are in sync, where the stops are coming around and hitting
the cables at exactly the same time. An eighth inch off or a quarter inch off is not good enough.
It has got to be perfect. You've got to make these adjustments with the bow press.
If you don't have a press, if you don't have a draw board, you've got to go to a shop or
somebody that does so you can get this corrected, because this will affect your vertical broadhead
flight. If you're having those issues, you definitely need to double check this.
The last thing I want you to double check is your fletchings. If you're shooting a big fixed
blade broadhead, but you've got tiny little fletchings to steer that arrow, you've got more
steering in the front of your shaft, which that broadhead is going to veer and lead that arrow
off in whatever direction it goes to the easiest. That is going to give you inconsistencies with
your shooting, so make sure you do have enough fletchings on the back of your arrows. Normally,
I don't see this as an issue. I usually see people have way too much fletching or way too
much helical on the back of their arrow, but sometimes it's better to be a little bit more
than not enough. Now, one final tip of what I personally like to do is I like to keep a couple
bear shafts in my quiver just to shoot to double check to make sure they are flying on with my
fletch shafts. I do this because I don't always want to shoot broadheads in the target tearing
up my targets, but a bear shaft arrow will give you the same results and the same reaction that a
broadhead tipped arrow will. If the bear shafts are going right, your broadheads are likely to impact
to the right, vice versa for all the directions. So, I do always recommend keeping some bear shafts
on you just to double check your tune, especially if you're on a trip, really hard on your equipment,
or worried about something that might have moved. If you want to learn more about bow setup and
tuning in general so you can learn how to do it yourself, check out our Ultimate Bow Build
Masterclass, linked in the description below. If you enjoyed this video, please like it,
please comment, please let us know. If you have any questions about broadhead tuning whatsoever,
please comment them below. We're always happy to help, and again, we always appreciate you
guys watching. Thank you so much, and we'll see you on the next one.
