Make a Slab Textured Mug and Use the Pottery Wheel to Shape It

Ceramic Art Studio
35 followers
Dec 13, 2025
Today I'm going to show you how I make a, start off with a hand-built cylinder
that I've added texture to and then I put it onto the wheel to open it up. So I start off with this,
this is what I call my medium mug. I think it's somewhere in the 14 ounce range depending on
how much I open it up. So it's a nine and three quarter by six and a quarter
rectangle and I use a three and a quarter inch cookie cutter to cut out the base. I have these
cookie cutters that I got on Amazon and they're great because they come in all different sizes.
So I am going to be using a texture roller that I did using an extruded
cylinder. They're not perfect but they're really fun. Here's another one
and this is the one I'm going to use today and this one is really off. I just noticed that
and I sometimes I've done this with texture with a fist stamp that I've made and I find that all
these get kind of sticky and on a wheel thrown piece it's even more difficult. So I have a slab
that I rolled out. It's sort of a soft leather hard. It will still flop down and it's about
three-eighths of an inch thick. I actually used these sticks that I have that are three-eighths
an inch thick to roll the slab out. So what I'm going to do is I'm just going to cut this piece
in half and use it for one month and normally what I do is I will be working on multiple
months at a time so that I am doing like all the same steps at one time but today for this video
we're going to make the full cylinder first and then move on to the next step. So I'm going to
roll this out a little bit. I think this is actually wide enough. Yeah so I'm going to get
it to about a quarter inch. I would say if this is the first time you're doing this I would leave
it a little bit thicker to start because you want to get a feel for how thick, how deep your texture
is when you roll it in and how much clay you want depending on how much you want to roll the
cylinder out. So this is going to be longer than what I'm doing. Hopefully I have enough here to
do the base also. But it'll roll out a little bit more when I put the texture in. So one important
thing is to make sure you keep your cylinder at an even thickness because you don't want to have
it be uneven when you're opening it up and I've done that and had it uneven and it works but it's
not as good. So we want to compress it on both sides and I'm seeing that this side on the top
is a little bit thicker so I'm actually going to roll from that direction. I'm going to turn this around
okay now I'm going to take my roller and because I want to have a little bit of a part of it that's
blank for the lip section without texture I'm going to put this towards the bottom. I mean
I'm not going to center the roller on this piece of clay. So now the trick is pressing down hard
enough to get a good impression throughout the whole thing. So I try to do it pretty slowly
putting a fair amount of pressure on and I always seem to get a spot that doesn't have anything in
it. I'll show you how in this case with this roller I kind of fixed it and it doesn't seem to matter
much that it isn't. So I think that because of this little flat section I don't always get
texture so I'm just going to take my roller and I'm going to just press in a little like that
now let's release the clay and I'm going to just you saw this side stretched out but this is not
so I'm just going to thin it out a little bit to kind of even it out and that's mostly to get this
line straight over here. I'm going to put my texture down and I'm leaving about an inch
this is really a personal preference over here that has no texture on it you have to figure
that one out for yourself. I just want to make sure I have enough for my circle and I do.
Very nice
so if you want to you can oh this is craft foam by the way
this over here I use it a lot it's inexpensive and very durable
like that if you want you can draw the line out first with a pin tool or something like that and
there
all right
and then we're going to cut out a circle
some of it might get rubbed away in the process but at least you have something on the bottom
and now is a good time before you forget if you have a stamp just stamp your signature in there
so right okay
that aside and I'm going to just take my fingers and smooth it along the edges just a little bit
okay and I use this tool by simp it's called an edge cutter and gives you a nice angle cut
I'm going to cut on both sides so I get this angle over here and do a little I'm going to
join the cylinder I'm going to take my scoring tool which is just part of a serrated rib that
you can see the clay has gotten quite soft from all this
okay and then we want to give it a little bit of memory that this is going to be a cylinder so I'm
going to just carefully not too tight give it a little roll on either side so hopefully it will
say I'm a cylinder and not pop open okay now stand this up and
so I do have a slightly thicker one side than the other
having that problem today
so I'm just going to pinch my one hand on the inside pushing from the outside towards my inside
hand flip it over to do the other side and you want to
so if you look at this you'll see that it's connected right
so it so there isn't like a extra fat section there it's all just um the two sides of the angle
are flush against each other on either side so I'm going to smooth this out a little bit
to um because when you open it up it tends to uh accentuate that line and you get split and
it's going to happen no matter what I haven't gotten it to the point yet where you don't see
it at all but at least um if you rub this in a little then it it works better and then you
could always just put the handle on this side so that you're not not as obvious okay so the next
step is the base so I have this um rounder that I made based on a video by Bill Van Gilbert so
that we can do that to get this base into the round or if you don't want to go that route
you can use like a yogurt cup on the right side so now this piece is the base is round
ish at least close I'm going to take my serrated grip
that ready and then I'm going to get my cylinder I'm just going to smooth the edges out a little
my circle now all I'm doing is just rubbing my thumb down flip it over do the same
oh this is even necessary because of the next step but it's just a habit I've gotten into
cleaning up the edge and then I'm going to take my serrated rib
okay flip on here
so when I'm doing these I tend to do a bunch at a time I'll cut out all the pieces and then I'll
cut the edges and make the cylinders and then the final thing is
putting the base on so I like to wiggle this a little bit get a bit secure
connection and then I would like to let it sit for a bit so I'm going to let this sit
and I'm going to come back to it in a few minutes and do the last steps for the cylinder
so the cylinder has been sitting for a couple of minutes with the top on and I'm going to
attach it so I've got my pony roller and I put it on a banding wheel just make it really easier
if you don't have one that's fine you can just turn the piece as you go so what I like to do
is I press down to get a good not very lightly in my soft clay and then I roll over and what that
does is it gets a little extra clay over onto the side that that adds a little thickness at that
base
you don't have to do it that way that's just the way I like to do it
and then I take my roller and I just smooth it a little bit
that little bit of clay and then we flip it over at this point you can see the top
my yogurt cup and I have this um oh first I'm going to use my finger down here at the base
to smooth it out smooth it in I've got my hand on the other side while I'm turning it
okay and I am going to use this brush it's a catalyst number four
polytip bristle short
anyway so what I'm going to do is I'm going to take this brush with a little bit of water on it
and I'm going to go down to the base and just go around so that I can sort of get that inside seam
to do uh nice and secure also we've taken care of the outside one to the inside and then I'm
take my brush and I'm going to just rub it with my this hand on the at my left hand on the outside
along the inside seam just to smooth it out and you know I'll take the brush this way and I'll
go this way and I'll just try to get rid of that line so that it doesn't get in my way when I put
this on the wheel and then the last step I like to do is let this sit overnight so that it gets nice
and blended together you can use your finger where you can reach nice and blended together
before I put it on the wheel so we'll be back so this cylinder has been sitting overnight covered
in plastic and is still um pre-leather hard but it's a little it's a little stiff you can see you
can wiggle it still so what I'm going to do is just check my seams see if if things are decently
connected which it looks like they are on this one and maybe do a little um evening here where
the uh seam is on the outside just do a little not evening uh making it more better a better
connection and I'm going to take my yogurt cup and round this again and then we're going to stick
onto the wheel so to do that we're going to wet the bat I have to clean it first
do put a little water on here you don't need too much but you just want a little bit
and then I'm going to uh move this around until I feel it start to suction so you can see how it
it's a little harder to push and then it's not stuck yet and then I'm going to put my finger
here and this is to get it to see how centered it is and this is about a crazy fast centering
this time it worked but most of the time I'm just constantly adjusting to get it in the right spot
so the next thing I'm going to do oops is take my long handled brush and press down to help
suction it a little more and you know you can go from the center out and that'll hopefully get it
in place again make sure that it's still centered and then I'm going to take my finger I'm going to
push towards the towards this little lump of you know how there's that little extra bit of clay
there I'm going to push towards there and then down so my finger is a little above the the lump
of clay and then I'm going to push the lump of clay down and and push it down to the wheel head
and get a little bit more suction to hold the cylinder in place okay and then make sure it's
still centered now the top may not look centered because this is a handmade cylinder it's not
perfect all right that's pretty good and it's close enough and I'm going to take my brush and
do a little bit of rubbing on that seam but I think it's pretty good maybe do the rounding again
just give it a little help and then I'm going to get my sponge and you can see how wonky it
is but I'm gonna thin this out a bit pull it up in it out and ignore the wonkiness
that's the hard part when doing this ignoring the wonky and you know we'll get it close to
centered it'll look at a glance as having been done on the wheel but if you look closely you'd
be able to tell that it was uh hand built and then put onto the wheel it's now I can never get them
like perfectly exact and that's okay and I'm just going to use my rib a little bit to help it get
centered okay that's pretty good and the next step so let me show you the rib I like to use so I use
this this rib and I'm going to hold it upside down and what I'm trying to do is push out when I shape
the mug is I'm going to push out a little bit at the top and as I get further down I'm going to
belly it out more and the thing you need to be careful of and why I suggest that you start with
a thicker slab initially is to not push it out too much and split the seam or put a hole anywhere
in it because you tried to thin it out when you were trying to get the shape you want believe me
I've done it many times in fact I did it earlier today so I'm going to take the rib upside down
because this is the shape this is kind of the shape that I'm going for and that's why I use
this rib and I'm going to push a little bit at the top and then as I move down where my hand
barely fits in here I'm going to push harder at the bottom so you'll see it belly out
more in the bottom sometimes the rib gets away from me yeah
it's a little slippery okay let's try that again so I hold my hold the rib like this because it's
usually I don't lose it when I do that but you know and I like a faster wheel but you don't have
to but I find that I tend to make a more even pushing out of the cylinder when I do that
ignore what's happening at the top ignore the bumps there's a lot you have to ignore when
you're doing this do pay attention to what's going on with your seam you might have to smooth it a
little and then always keep stop and check to see how things are going because it's really easy to
lose the control and either push out not where you want to push out or go right through the
clay because it is on the thinner side all right so I'm pushing at the bottom right now
and I'm just going to go up a little bit to make sure that the curve is somewhat even all right
and I'm almost there I'm going to belly out a little bit more but I want to check to make
sure I still have clay so I can feel that there is still clay okay let's just belly the bottom a
tiny bit more and then come up okay cool and now I'm going to work on the rim oh that jiggles a
little I hope it's still attached okay so there we go okay now the idea with the rim is you want
to get it um so that it's balanced with the base and I find that if I leave this too narrow at the
top for the bottom it looks unbalanced or if I make it too wide so I try to get them to be about
the same so I'm going to um all right I think we're almost there and I'm using a pretty dry rib right
now that's just me you don't have to do that if you prefer it to be wet do it wet get my chamois
and um I put a finger on either side of the chamois so I'm kind of pinching it down on the
rim and I pinch a tiny bit to thin out just the top of the rim a bit because that's where your
mouth is going to go and you want it to be a comfortable um connection a comfortable uh not
too fat rim and uh just comfortable on your mouth so you really need to pay attention to that and
I've seen people do this a bunch of different ways but this this way tends to work for me
um so it looks it gives the appearance of being thinner than the whole thing but it's it still
has thickness in in the rim it's just that it's more comfortable on your mouth so now let's take
a look so I think I just want to do a tiny bit more shaping on this okay I think that's good
and then we're going to trim the bottom all right so for this I got my wooden knife and I'm not
going to take a lot because there's not a lot of clay here but I want to get rid of that little
glob that I put down there so I'm just going to cut away be very careful because this is another
spot where you could end up taking too much clay and end up with not enough there to hold it
together and this might be close that was a little bit more than I meant but that's okay I think
we're all right now at this point it might pop off the wheel so you need to be careful but if it
doesn't um pop off now just leave it on there until it's enough that you can wiggle it off
see if you see how it's still stuck to the wheel you don't want to try to get it off because what
you'll end up doing is separating it um here at the base the cylinder from the base all right
so that's it for this step and we're going to let it sit for a bit until it's ready to come
off the back I forgot one step I like to re-accentuate this line here which you know
it's just for this particular pattern so I take my my rib the point of the rib and I just follow
where that line was be careful not to press onto the texture and then I'll just take my finger and
smooth it out a little and oh and there you go now it popped off so we can do the next step
and the next step is um I push in the base a little and this is a little too soft to do this
but when it's a little harder I'm going to smooth this all out over here make sure there's a good
good um that it's nice and smooth and then it'll be ready for a handle when it's dry enough
for to take it because now it's too soft so the mug is sitting and um well there's more than one
but sitting and drying and it's still a little soft leather hard I want it to get a little
stiffer but it's time to pull some handle so what I like to do is I have an extruder so I
use this one inch hole to extrude long coils and then I cut them into pieces that are somewhere in
and if you don't have an extruder you might like to do this with the same method by rolling out
coils which is what I used to do but then I like to take the handle to get it closer to the shape
that I'm going to be and I just slam it down a little and that flattens the sides so now I have
close again closer to the handle shape that I want over okay so now we're gonna pull the handle
so you want to get a good grip at the top and make sure your hand at the top is dry
wet going to slip out of your hand and dunk your hand into the water and start to pull
and here you don't want to squeeze too tight you're just kind of pulling a little bit making
sure your hand is wet turning your hand in this position so you want to do both sides so I turn
my hand and the clay so that I'm pulling it evenly on either side and when I get some length
in it I will take my thumb it's also wet and I'll just go down the center you don't have to do this
I just like handles that have that line that indentation so then I'll continue to pull
and every few times I will put my hand down the center again my thumb down the center
just to make sure I'm not losing it and sometimes to thin it out a little I'll just take my fingers
in a pinch and again you want to do both sides and that got rid of the indentation a little
and what often happens to me is I end up with this little lump of clay at the bottom I don't
know why I'm just going to pinch it off and when I'm satisfied with the length of the handle
the way it looks it's ready to dry so what you can do is you can do you can use that little
hunk of clay and you can put it down on the board sitting down like this but what I do is I have a
tube one of those tubes that posters come in and I put it over it's a probably four or five inch
wide and I like to put them over that so I'm going to take my clay my handle and put it over
my left hand and with my right hand I'm going to pinch away all that excess clay and I'm going to
just let it dry and it gets a nice curve on it but I don't I'll let it be still soft leather
so I'll be back when the mugs and handles are ready to go so I'm ready now to attach the
handle the mug is leather hard just this this part's nice and stiff and this is still a little
bit soft but it's ready to go and I like to try and smooth that seam out a little on the bottom
I pushed it in I'm not sure I showed you that earlier just a little bit so that there's um
so you can see that the only the edges will touch the table and now that texture won't
be on the table okay so I'm using a towel just to give it some support so I've got the handle
it's still bendy so it's a soft leather hard and the first thing I do is I hold it in my hand
away from my with the knife away from me and I cut it at an angle cut off some of the clay
and I'll also trim a little bit of this edge off because it's a little too much clay and then we're
going to take it so you can see it's so soft enough to do this I'm going to pull some clay
forward so there's a little bead of clay there that I'll use when I attach the handle
maybe smooth this out flatten it a little and score it okay so now it's ready to attach
so I'm pretty um consistent in where I put my handles on this particular shape mug so I'm just
going to score at the top and I do that right at the part where the uh where there's no texture
and then I go down to the bottom just where the curve where it starts to
um come down in the curve and I will score there okay so now that's ready
and I've got some slip I'm going to put it on the top one the top area because we haven't
sized out the handle yet for the bottom and I'm going to push the handle into the my
my left hand is supporting the mug even though it is pretty stiff and my right hand is pushing
towards it and I'm going to wiggle it a little so you see how it's moving and at some point
it stops moving and I know that I have a good connection and then with my thumb or fingers I'm
just going to smooth down a little bit um here I'm getting yeah like that and now I'm going to
leave this alone for a moment at the top normally what I do is I do multiple handles at one time
so that I um will do like this on every mug and then I'll go do the next step and then I'll come
back when this is set up a little bit but for today we'll just do the one mug so you can see
this is way too big a handle right now so I'm going to cut back some of the handle and the way
you do this one is you want the angle you're going to cut towards you so that the angle is going to be
such that it will sit flat against the mug so I'll put it down here and I'll look again and it's still
too big so I'm going to cut a little bit more off one of the things that I heard one potter
describe was that if this distance here is more than half of this distance here then the handle
is too big I mean it really depends on what you're going for and I mostly do it by eye so I'm going
to cut it towards myself again and that might have been just a little too much so you see it's at an
angle no no that's probably good okay and I'm going to see if the mug looks good at that position and
I think that's a good place so I'm just going to score underneath and the advantage of having this
sitting down like this is that you can see that your handle to make sure that your handle is
straight and I'm going to do the same thing I did at the top which is put my hand in here
right and I'm going to wiggle it around make sure I have a secure connection and then
using my thumb I'm going to just blend it in a little okay so now we can go back to the top
so for this part I use two tools I've got the rubber tip tool and I've got a stiff brush that
I used in an earlier part of the video and see all that little bit of extra clay there
I'm going to just blend it in and push it down a little and blend it in and then that's going to
give a nice solid you know there isn't like a little gap there and it makes the handle look
like it came you know was pulled out from the pot which is what I like to do some people like
to show the connection I like to blend in the connection so it's really what whatever you
prefer and then I'm going to take the stiff brush and just rub it in a little bit more
because my rubber tool doesn't get in there very well okay and the finger always a good tool to use
just want to make sure everything looks okay sometimes I get a little bit of nail doing
something I don't like but this looks pretty good and then we're going to basically do the
same thing at the bottom I'm going to take the flat end of this tool and I'm going to just
slide it in here and the other side and make sure I have a good connection there too and I'm just
going to take that brush and you know sometimes you might need to add a little water to the brush
let's see and that's pretty much it we've got a handle and it looks pretty good now I'm going to
dry this um sometimes oh one other thing is you can take your finger and just accentuate that
curve if you want to have that little lift over there so now I'm going to let this sit set up
under plastic for a day or two as I said I'm in a garage and it's pretty humid in here so I'll
probably just let it go for a day but I want all the clay you know the different parts to meld
together before I leave them uncovered so if you're in a dry area I would leave them covered
for longer than a day but I guess you'll figure that out based on what your um humidity level is
anyway that's it and um I hope you enjoyed this video and thanks for watching
