I have had some time to give the new forge setup a good trial run. This forge exceeds my expectations and I am loving having the coal forge back in the main shop.
Blacksmithing and related activities can be hazardous. These videos are not a substitute for competent professional instruction. Your safety is your sole responsibility. Always use appropriate safety equipment including eye and ear protection when working in the shop. Follow manufactures safety guidelines for the use of all equipment. In the event something shown in one of these videos seems unsafe, it is up to you to make the appropriate changes to protect yourself.t yourself.
I've been working in the new coal forge now for a couple of weeks and I thought this was a good
opportunity to tell you what I think about it and maybe to clarify a few of the details,
things that might not have been obvious when we were building the forge in that previous video.
Now a few years ago when I took the old coal forge out of the shop that was primarily because
I worked mostly in a gas forge and I was trying to use the induction forge more. I really like
induction technology. It's quick, simple, clean and more economical than either of the other two
choices. But I didn't really have room the way that forge was designed and built to have the
coal forge and the induction forge readily available all the time and that was a higher
priority to me than having a coal forge in the shop. Because at the time I didn't really work
in coal very often. It probably was less than five percent of my total shop time was spent working in
a coal forge. Not that I don't like working in a coal forge but for production work the gas forge
is way more efficient and for quick simple jobs the induction forge is more efficient. The coal
forge better suited for ornamental work and things with really odd shapes that don't fit very well
in either of the other two forges. I did kind of miss the coal forge and I found that going over
to the little shop has been rather inconvenient because I often want tools that are in this shop
whether it's punches, chisels that are stored up here and I have to keep running back and forth to
get the tools that I want to take over there or if it's because I need the power hammer,
treadle hammer, fly press, the KA-75, any of those bigger tools are all up here in this shop. So trying
to work efficiently out of that coal forge over in that shop really was not a very practical
solution to the problem. It was workable. I could get things done when I needed a coal forge
and it was better than not having one available at all. But the main use for that shop really has
been YouTube videos and it's more of a blacksmithing theater if you would than a functional shop for my
work. It would be a perfectly functional shop for most hobbyists because it is a nice small shop.
It has everything you need. Forge, hammer, anvil, vise, workbench and a selection of hand tools but it
doesn't have everything that I like having in this shop. Anyways, I could see a reason that I
would want a coal forge back in this shop and I also have always liked the idea of a big solid
masonry forge, stone, brick or in this case adobe over can walls. Now if you didn't see the can wall
construction of this forge, I will link to the previous video where I showed you the construction
here in some very abbreviated detail that wasn't a how-to video. It just gives you an idea of how
this forge was actually built. But the other thing that I really wanted in a forge that was the
ability to have the coal forge, the gas forge and the induction forge all available very quickly,
very easily without having to move things to the outer shop and wheel this in, wheel that out and
it just became a real pain with the old forge in here. Obviously the coal forge is in the middle.
My minimum hope for this forge was that the chimney would draw as well as the one that's
over in the little shop and I am really thrilled with this. It draws better than the one in the
little shop by a considerable amount. In fact, I don't think I've ever worked in a coal forge
that has the draft this one does. The same 10-inch chimney pipe I had before that never
went away. It's been sitting here in the roof doing nothing for the last couple of years.
But the chimney opening is just a little bit better. It's lower down. It's right on the hearth
instead of being up in the air a little bit. It's a little bit smaller opening and it cantilevers
over a little bit at this top arch so that it really kind of funnels the smoke up there.
Very little if any smoke in the shop when I'm working with this. It's been really pleasant
to work with. The induction forge then fits over here and I don't think it is close enough
to the coal forge that the heat from the coal forge is really going to bother it. It's pretty
far away. But I've got a little piece of cement board in here as a little temporary heat shield.
I'll probably make something more permanent that helps deflect any heat from the coal forge from
the electronics of the induction forge. And I don't think I'm going to have to move this very
often. But I can move it. The cooling unit is down underneath here on a little cart and I can
roll that out. I can set this on top of it and I can move it out of the way. Ideally I would have
had a cart, kind of a C-shaped cart that the cooling unit went under the forge and the induction
forge then was on top like it is here. But things just don't line up under there. It would have been
kind of off to one side. The cooling unit's actually kind of in here and this is over here
and it just was not going to work out well to do that. For now it just sits up here on the hearth
and it works out rather well. When we did all the wiring for this, we hardwired the blower for the
coal forge and then wired a switch in for the cooling unit so I don't have to bend down or
reach way back in here underneath the coal forge hearth to get to the cooler switch. It's just
right there. That's all it takes to make the induction forge operational.
I can now work in here if I need to and it's real quick and easy. I don't have to set it up. I don't
have to worry about whether or not I'm actually working in the gas forge or the coal forge. I need
that little isolated heat so this is really convenient to be able to use it that way.
It's going to take me a while to remember the switches over there. I always still want to go
underneath there to switch on that cooler. But I think this is going to work out really well.
It makes it super easy to use the induction forge. If I'm doing something I just need one quick heat
piece of cake, come over here and do that. Or if I'm working on something that needs
some advantages of one other forge or this forge, it's easy to go ahead and use both.
Now for the propane forge, I have it sitting on this end of the hearth. The heat really isn't
going to hurt a propane forge as long as the hoses are not anywhere near the fire.
The ribbon burner forge I was using takes up way too much space. It was a much bigger forge box.
It had the blower that was mounted underneath it. That's not going to fit here. An atmospheric
forge fits here just fine. This single burner chili forge is what I'm using right now because
I need to reline my double burner chili forge. When I get that done, it will fit here almost
as well as this does. It'll just come a little bit further forward and it'll be a perfectly
fine place for that. The only problem I have is that the hoses are not long enough to route all
the way around behind this forge to my regulator which is mounted to a post over there. So I need
to get some extension hoses. Not a big deal. I just haven't gotten around to that yet.
And to keep the hoses off the floor, I actually put in a piece of conduit in the back of the
chimney about that far below the hearth so it's not going to get hot at all. And I can run the
hose through that and get to the regulator over there. Maybe I'll put some quick releases on
there so it'd be quick and easy to swap forges out if I needed to. And that is one thing about
gas forges is they often need an assortment of gas forges to have different size chambers,
longer heat, shorter heat, wider material, that kind of stuff. So it's something I find that I
have, I think, three that I kind of switch back and forth between right now. There was a question
from somebody about how far back my fire pot is here. It really isn't that bad. You don't need to
reach in the middle of a fire pot unless you're cleaning out the previous fire. Or maybe if you're
starting a fresh fire for the day, you need to get in there and work with that. But the rest of the
time, you're holding on to the end of a bar that's sticking out this way. Or you're working with a
pair of tongs and you don't have to lean over at all. So this really is not too far reach there.
The clinker breaker is right here on the front, so it's easy to get to. I have a damper for the
blower here on the front, so I don't have to reach under there to get to any of those things.
The ash dump is kind of far back in there. It's kind of a pain. I need to see if I can figure out
a way to put something right in here that operates at some sort of another extension lever or
something. Haven't thought about it too much. Not a real big deal. You only need to dump the ashes
once or twice a day while you're working. Or at least that's all I dump.
Now, there are some also questions about the adobe getting hot and flaking. I don't think
that's going to be an issue. Adobe fireplaces and baking ovens are very common in this part
of the world, and they don't have any special treatment. It's just adobe that takes the heat,
and they seem to last just fine. The only problem with those is that the baking ovens are often
outside, and the rain wears the adobe. They erode a little bit and have to be
re-coated on the outside from time to time. But the insides don't fall apart because of the heat,
so they take the heat pretty well. On the other hand, this is firebrick on the inside
with refractory cement holding the firebrick, and this archway is built up out of refractory cement,
so it is not adobe. The adobe is actually outside the hottest part of this,
so I don't think it's ever going to be a problem. And if it is, it's going to be really easy to fix,
because after all, it's just mud. Another comment that I saw quite a bit was that the
can wall construction, the cans were just going to melt out because this was going to get too hot.
The hottest part of a coal forge is down inside the fire pot. What goes up the chimney is not
that hot, but again, the chimney opening is firebrick and refractory cement, and then this
section of chimney pipe that comes up to this black pipe is actually a bit of double wall stove
pipe, so it's insulated double wall pipe. It's meant for wood stove, and wood stove chimneys
take more heat than coal forge chimneys do. And then this black pipe is conventional stove pipe,
so it's going to do just fine. The cans are never going to melt out of this, and the bottles aren't
going to get so much heat that they're going to break. All of that is just stylistic, and it's
not going to pose any kind of a problem in this. Of course, I made the little door that is on the
back of the chimney, so if I need to run a really long bar to heat the middle to punch a hole, put
a twist in, something like that, I can run all the way out the back of the chimney just by opening
that little door on the back. And I think that's going to be a good option to have, even though I
don't anticipate using that feature very often. So the short answer is, I'm loving the new forge.
I think we're going to see more work in the coal forge as we go forward. Probably a little less
work over in the small shop, although we will still go over there and work with that equipment.
It's still a good little shop to show that you can get by without all the fancy stuff I've got here.
But I do like where this shop is going, and I really want to spend more time in this shop,
which means I won't be able to spend quite as much time there. Oh, another thing, the blower here,
it has a rheostat on it, so I can turn the speed up and down. And it has a switch wired in,
so I can leave the speed set at a certain speed and just turn the switch on, and the blower will
come up to the set speed. It comes up a little slowly, which I think is a feature of the rheostat.
If it was turned all the way up to the high speed, it would come up to speed a little quicker.
But it's not really a big problem. This blower seems to me to put out a higher volume of air,
but it doesn't put it out at the velocity of any of the blowers I have had on that other
forge over the years. Same firepot, they're both Centaur Vulcan firepots, but that other forge,
it seemed like it was always really hard to get a good heat without too much airflow.
And this one seems to have plenty of air-moving oxygen, but it doesn't have that velocity that
burns your fire hollow. Hard to say. Maybe I'm just imagining things. Maybe I just wish it was
better. But I really think this Centaur PB50 blower is a better performing blower than anything
I've had before. No, I'm not being sponsored by Centaur. I just bought the best stuff that
I could afford because I knew I didn't want to have to rebuild this forge in the future.
Anyways, those are my thoughts on this forge. I want to thank each and every one of you for
watching the video. A special shout out to my channel members and my Patreon patrons.
Channel members receive early access to the videos, while Patreon patrons at the $5 level
and above not only receive early access to the videos, they receive those videos ad-free over
on Patreon, as well as very occasional exclusive content meant just for Patreon, like less than
once a month. So if you're tired of the annoying ads or some of the sponsored content on YouTube,
Patreon might be worth checking out. Anyways, thanks again for everybody watching the video.
It really makes a difference. Hope you have time in your day to get out to your shop,
make something, have fun, but stay safe, wear your safety glasses,
and we will see you for the next video.