WTFIdea/Whiskey Two Four: Crye Compatible Hydration Panel

Ballistic Lab
1 follower
Dec 3, 2025
WTFIdea/Whiskey Two Four: Crye Compatible Hydration Panel
Hey guys, tonight we're looking at the Whiskey24 WTF idea cry compatible hydration back panel.
There's a lot of interesting features rolled into this thing. It's very well done. I believe
it's sub $100. It was sent to me, so I don't know the exact price, but it is an alternative to
the roughly $200 cry panels while giving you a lot of the same functionality
and a lot of the functionality that I think most people care about without some of the features
like the breaching tool pocket that a lot of folks don't necessarily need or want.
So let's get it on the table and take a closer look at it.
All right, so like I said in the intro, this is the Whiskey24 hydration back panel for cry carriers.
So it's going to be compatible with your AVS, your SPC, JPC2, and then anything else on the
market that's using cry pattern zippers. So some of the Spitfire stuff, the Grey Ghost carrier,
all of those should interface well with this, but it was specifically designed for cry. So
as you attach it, some of the attachment methods may not play super well with other things,
and I'll show you those. So hopefully you can check out what you have and be more prepared.
All right, I do have this on a small SPC with eSappy in there, and it fits just fine.
I have no concerns that it would also fit a medium without any issues.
So let me kind of take this zipper off and I'll show you the mounting here,
and then we'll take it all the way off and show you some of the features here. So
bear with me. Sometimes this gets a little goofy when you got a plate in there. There we go.
All right, so now when we look at the mounting here, you have a couple of different things that
you can do, and depending on which exact platform you're using, you may not need to use all of these
features. All right, so kind of one of the staples of the WTF back panels, or some of the
front panels for that matter, is this kind of bottom flap here. So this will engage with the
plate pocket, so it'll wrap around internal of the plate there and then secure into the plate
bag itself, which in all honesty is probably my favorite bottom mounting of any of the panels
that are out there. It's relatively drama-free, you don't need to weave anything, you just have
to access your plate pocket. So there's very few exceptions to where that would be an easier option
than trying to weave things. All right, and then looking at the top here, you have these kind of
Velcro-backed Powell's webbing or MOLLE webbing, however you want to look at that. If you're just
using this for hydration with the SPC specifically, because it's got the loop-backed MOLLE here,
it does engage fairly well on its own. It's going to pull off because, you know, I don't have the
other zipper on there, but with the other zipper on there, it does engage fairly well. If you want
it to be a little bit more secure, this is designed to be woven through the MOLLE and then kind of
Velcro back on itself. So the Velcro is really there because you don't have like a mouse clip or
a snap closure on here. All right, looking at some of the features on here, I'll show you one and then
we'll get the vest out of the way. There is a zipper tab keeper on the bottom of these zippers,
which is a very nice feature. If you're at all concerned about your zipper backing off,
which can happen, especially on the longer Crye panels, if you store them and they're pulling up
like this because the panel's longer than the vest, sometimes that zipper will start to work
its way loose. This one doesn't have an issue. It fits very flush, which I know is a big deal
to some people. So if you don't like the 2.0 panels, this might be a good option just because
of that flush fit and you don't have to pay collector's prices to get like a 1.0. All right,
so we'll get this zipper tab keeper out of here. All you do, it's a little bit of elastic and you
just tuck the tab in there and the zipper can't back off. So we'll unzip this and get the vest
out of the way and work through some of these features. All right, so you do have a fairly
generous Velcro field on the back face of this thing, or the front face, however you want to
look at that, the exposed face. So you can still have ID placards and whatnot. If you want to do
the CAG mod, you could have your Velcro mounted triple flashbang panel on there. That would work
out just fine, just like on the Crye pack panel. All right, you do have a good bit of shock cord
routing in case you want to stuff a cold weather layer or something in there, and that is very
easily removable if you don't want to mess around with the potential snag hazard. All right, I know
it looks pretty bad right now, but if you were using that and you policed it up a little bit,
I don't think you'd have huge issues with it. But again, you can pull it off as needed.
There's a hardy grommet on the bottom of this thing, which I really appreciate on a hydration
pocket more so than probably anything else. I've had bladders burst and Cordura does have a little
bit of a water resistant capability to it. So without a grommet, it will hold on to that water
longer than you would like it to. So with the grommet in there, if something happens to your
bladder, hopefully it will purge itself from your carrier and you're not carrying around a bunch of
water that you can't drink anyways. All right, zipper tabs are very nice. Zipper tabs are these
Hypalon tabs, so they're silent, but they're easy to grab. And then the zipper is a very smooth
functioning zipper. It's a little bit on the smaller size as far as teeth go, but for this
use, it's plenty strong and it opens very nicely. And then as you look inside here, it is just a big
voluminous pocket with a keeper tab up here that will engage with most bladders out there.
If it doesn't, you can very easily work some paracord solution here to help tie your bladder
up to the top of the pocket. It does not, however, have cord routing or bladder routing,
tube routing, if you will. So you're going to need to bring your zippers kind of up to the top and
then kind of meet where you want the tube to come out of there. Not a huge deal at all. Maybe, let's
see here. Oh, look at that. Missed this earlier and then I caught it as I was trying to show you
guys. So you can also route the tube through this pass-through here. Let's see if I can access that
from the inside. So right here is where the access is inside and then that'll pass through
up there. So my apologies on that. You can run the bladder out through there and then you've got
these one-wrap loops here to help retain your tube. That's very well hidden actually.
You may need to take the bite valve off to get that through there, but it's actually more generous
than it looks. So it could potentially pass through there. I would say this is fairly comfortable for
a 2-liter bladder. I wouldn't want to push a 3-liter unless it's one of the wide ones
and then you just have a little bit less capacity used. That should fit in here just fine, but the
long boy 3-liter bladders I wouldn't mess around with in here. They'll get folded and you'll kink
your flow of water. Alright, I already showed you the back. You do have a couple of webbing
loops up here. I'm not sure if you can mount this to one of his harnesses, but you could
absolutely use it to improvise something. You could tie off on stuff if you needed to.
All told though, it does mount very, very securely. I'm a huge fan, like I said, of the bottom mounting.
The top mounting is more than adequate and it's a very nice clean fit with the zippers.
You don't have a lot of excess bulk. I don't know if you could push this to a large carrier,
especially with eSappies and backers. I don't have those to test, but I'm comfortable that
it would fit on a medium if that's what you were using. So there you go. That is the Whiskey 2-4
pry-compatible hydration back panel. Solid budget option if you want to get into zip-off
panels. You want a bladder on your SPC or JPC that's easy to remove.
Very nice, very nice product and extremely lightweight. It's very well made. Thanks guys!
