BlackHorse Mig-29 1635mm Turbine - Modifications & Upgrades overview

Sixth Sense Aviation
1 follower
Nov 10, 2025
Paul ZRC here coming to you from my garage in Texas and this video will be about some
customizations I made to the MiG-29, the Black Horse MiG-29. The previous videos you saw were
setup and configuration, this is some customization. So as you notice we have a double
nose wheel, we have different main wheels that are a little more scale. I just want to go over
all of that and also talk about the thrust tube that's been a problem but I have one that works.
So this is what we want to talk about. Let's go! So the JP Hobby pipe just arrived. I just wanted
to show you all a big comparison. This is the new pipe, this is the old pipe. As you can see
already starting to discolor here from the heat. So I took it out just in time. If you see I
actually provided these measurements. So this back here everything is the same but here is the
big difference and that's the length of this front part where the split begins and also notice the
cooling. The cooling shroud begins way before the split so air is channeled in here, cools it off
versus this one where all the channeling is basically just for the rest of the pipe. The
big difference is yes the outer shell is very very thin but that's just the outer pipe.
The inner pipe is much thicker metal including the V piece here with additional reinforcement inside.
I'll try to show it to you. I don't know if you see that but there is an additional
piece of metal on that split right there so this pipe should last a lot longer or at least you
know forever for as long as the model. One big difference is the size of this bell mouth if you
would much larger. I do not think that's going to fit. The good news is that the diameter of this
part of the pipe is the same and I should might be able to use the original bell mouth. Yes it will
suck in let's say less air around the motor but I may not be able to fit this gigantic thing so
we'll see more to come on that. Okay so here you can see what I had to do to fit the new thrust
tube. There was a support here that I cut out. I don't have a picture of it now but this was
removed and you see the two spots one on the top one on the bottom that's left over from that
and I had to shave off this one down here really flat to make the tube lay down and fit in here.
This doesn't seem to have any structural impact on on the fuselage. It's been flying like this
many times now and it works great so just FYI again this is a view
towards the back of the airplane in the inside of the fuselage. Okay what you see here is
the JP Hobby thrust pipe installed and I did change out the bell mouth. This is the original
bell mouth as you see it fits beautifully inside the new thrust pipe and of course in front of the
right behind the engine as well because I kept the original bell mouth. As of the time of filming
this I've had many many flights at least 20 plus now with this setup and the cooling everything
works great so I recommend using the original bell mouth. It'll be much easier to lay the flat
the pipe flat in the fuselage after shaving off that support that is behind there.
That's my recommendation as you see it fits really well. Let's look at the main
retract modifications. I bought the JP Hobby struts that you see here. These are the ER150
170 millimeter length 16 millimeters in diameter and the strut 10 millimeter on the main axle
there a rotating axle and the wheel is six millimeter and here you have the original
black horse or I think these are made by Phoenix model so as you see these struts are perfect
length they put the axle of the wheel exactly at the same place and now they will look much more
scale and here's this pin that's on the retract on the original literally is 9.5 millimeters for
some reason so it fits into the 10 millimeter hole. I had to drill inside there a little bit
because it wasn't going deep enough it stops right there at this boundary but if you drill
a little bit with your drill press it can go all the way in and now you have a good
good you know good fit here and perfect same length there's one caveat the wheel
on this original retract as you see is pretty much at the same depth as the
actual strut itself this one will go under this which means it has to go deeper into the fuselage
so let me show you what I did the modification I basically took my exacto knife and this plastic
bottom here I just cut it so when the wheel goes in it pushes and there's plenty of room behind it
and pushes in and lets the retract close or retract all the way so that's how I'm going to do
the mains I am doing this for two reasons I like the scale look but also the JP hobby struts
they just operate so much nicer there's some dampening they don't just you know work like
a strut with just a spring in it there is a spring but there's some dampening so I think
they'll behave better during taxing but also on landings so that's the mod I'm making to to make
the jet a little bit more scale notice again still don't understand why black quartz couldn't have
put proper scale struts I in terms of the retracts the mechanisms themselves I'm going to leave the
the housing but I am replacing these motors with JP hobby ER with an M4 shaft and 60 millimeter
wrong so these are longer shafts than in the nose wheel these will be drop-in replacements the JP
hobby ones are much quieter they don't buzz as much and and they rotate faster so the retracting
will be faster these are very very slow right now and a lot of people have reported that they
strip inside so I don't want to risk it I'm replacing those two and here is my nose
gear also converted to a dual wheel more scale look using the JP hobby ER 150
double nose wheel strut so just to show you how that fits into the fuselage perfectly and
much softer spring I put the softer spring in the strut so I get that mig 29 classic nose leaning
down when you and when you break so with the wheel hanging down below the strut versus being
in line with it there is an issue with getting the retracts to close and then come back up
basically the motor wasn't able to close the retract all the way so this little slider that
goes inside the trinion was just over the hump here and then the motor couldn't lower the strut
a little bit lower to pull it back out so what I decided to do is stop the travel so that the
retract stops with the wheel just as you see here this is like the bottom of the retract well and
the wheel will be just slightly above it with this sticking a little bit out of the fuselage
which is fine because I'm gonna have gear doors over it the way I did that is I just added a
cylinder right here that stops the trinion as you see from moving past a certain thing and this is
a nice way to do that because you can tune how far up and down the retract stops and what point
it stops by adjusting the diameter of the of this little added cylinder so I had to experimented
with and I settled on this one this one wasn't too thin so that's one recommendation again
still when the retracts are fully deployed and open slider locks in here on this side
and everything works beautifully this is just to adjust how far it closes to leave room for the
wheel which is now again below the strut versus in line with it this is more of the scale
the way it is in the fuselage retract opening was not prepared for that so because again
Blackhorse decided to use sports jet wheels on the Nik 29. So with this picture I wanted to show you
the mod I made to the nose wheel. I replaced the motor with a JP Hobby one and this is a strut
that's an ER 150 from JP Hobby and I'll have links to all of these in the description below
and I've put the two 65 millimeter wheels on it so it looks much more scale I painted them green
and then again I put a softer spring in the strut and let me show you on this next picture
I basically cut the original strut here off right there and the ER 150 fits inside of it
and I was able to fasten it with this screw here this plastic holder here for the light
I basically copied and slightly enlarged the Nik 29 lamp holder that Freewing uses
and this is just 3D printed so I added this but again the ER 150 strut from JP Hobby fits inside
the opening of the original Phoenix landing gear strut for the nose here it's thinner but it's
strong enough and fits in here and I was able to fasten it with the two screws one here and one
on the other side so don't doubt show that as well. So I wanted to show you all as a final my
inspiration for the landing gear this is a Nik 29 near Krakow in Poland at an open air museum
basically aircraft museum and as you see what the gear looks like this was kind of the inspiration
for for this semi-scale model see here is the mains on the full scale mig it's kind of angled
differently but you know close enough with the struts and here's the nose wheel it's got some
more elaborate movement here it has a hydraulic pushing element here but anyway this was kind of
my inspiration for this model so hope you guys enjoyed enjoyed this. Thank you for watching
and please like and subscribe to get more of this wonderful content
