Throwing and texturing a mug on the pottery wheel

Ceramic Art Studio
35 followers
Oct 8, 2025
Throwing a cylinder and texturing it. You start with a pound and a quarter of clay
and throw a very straight sided cylinder, coning up, coning down, centering the clay.
Notice how my hands are always touching and that just keeps your hand more steady. The first pull,
the wheel is going slow and always pay attention to the rim.
Back to the rim, just making sure it's centered.
All right, so now I'm measuring the size of the cylinder because my bottle needs to fit in it.
All right, I'm making the second pull. The inside fingers are curled,
the outside finger does most of the work. It's pushing in
and a third pull. Inside fingers are curled, outside finger is beneath it
and now you're going to center the rim. Notice how I always go back to the rim between each part
and I have to color it in because the bottle is going to have to fit inside the cylinder.
You don't want it too large, too wide. Nice even pulls back to the rim.
So now I'm going to measure it and it fits pretty good. Now you have to get all the slurry off the
side of the pot, inside and outside. You could do two at a time but here I'm using a wooden rib
to bring the side up very straight for when I texture it. You want a really, really straight
sided wall and back to the rim. Now I'll go on the inside and take the slurry off the inside
with a metal rib keeping the wall straight and I'll kind of put the rib down across the bottom
of the inside too. Take all slurry off. There you go. It's going to go down the bottom. You push
and bend the rib. Okay, more compressing and drying. It's really drying the walls,
getting all the slurry off. You don't want the wooden tool to stick. Okay, back to the rim
and measure. All right, so now I took a wine bottle that's the size that I want to make it.
That's what the calipers are measured to and I wrap it in newspaper. This is going to create
a support wall for my textured tools to press against and you want to try to make it not
wrinkled. These are my textured tools and the bottle goes in. Now the bottle, there's a little
space so now you have to move the wall snug against the bottle. You want to start at the
bottom and use the tool at an angle to bring up the wall up and in before you collar it in more.
If the tool is vertical, you're going to end up folding the clay. It needs to be at an angle like
this and collar it in and then just clean up the lip or the rim of the pot because it gets
a little wonky with the paper there and get all the slurry back off the pot. There you go, there
I am cleaning up the rim. Okay, so now you have a nice straight wall, no slurry and we can decorate
the surface of the pot. I'm going to start with a line, making a line to roll to with the tool
and the roller tool is a little small, the finger roller, so I'm going to use spacers that I made
out of a pencil guard. I just cut them up, they're little rubber things I cut up
and that makes it a nice snug fit for the roller
and I can get in low to the foot doing it this way. All right, so you're pressing against
the clay and the bottle making your design and this is the fun part. When I'm done with
the design, I'm going to set the pot aside to to dry up a little bit before I can take the bottle
out. It's very wet right now, so you do want to set it aside and let it dry out a little bit
before you touch it again. I'm just adding a little more detail to the very bottom and this
is just a stamp. All these tools, these are MKM tools, I wet them before I use them on the clay,
it makes them just roll nicer. Okay, so it's sat aside for about 20 minutes. I can pull the
bottle out and just carefully get the paper out and now the inside's going to be a little messy,
you're going to have to go back in and clean that up and the rim is a little messy, so you start
with the rim and re-center it, get everything nice and neat and even and this takes a little
time, so patience is key here. Notice how my finger comes in at a 45 degree angle and you
want to wet the inside a little bit so you can clean it up and now the tricky part is throwing
a shape without touching the texture on the outside of the pot, so you can only throw from
the inside and this video's sped up a little bit, I'm going pretty slow to do this and with
each pull you go back to the rim, re-centering it. Now I'm pushing out from the inside, I'm going
to push out and try to make a mug shape and it's a slow progression, you don't want to move too
quickly because the low spots, there's high and low spots with the texture and you don't want them
to rip, so you want to take your time and go slow with this and it's almost done. One more time at
the rim and all it needs is a handle.
