Today we design and manufacture a 3D cube face grain cutting board from 3 types of wood: Amber Tree/Satin Walnut, European Walnut & Sweet Chestnut :) Enjoy this amazing creation! =D
0:00 Intro and Jig Creation 1:41 Preparing the Lumber 2:31 Sliding Table Saw Action 3:33 Polishing and Glue Up 5:53 Finishing the Rough Work 7:46 Sanding, Finishing & Final Reveal
today we create a beautiful 3d cutting
board from three types of nut wood enjoy
this project was mainly intended to test
out the capabilities of my new sliding
table saw
for the board we need a bunch of 30
degree angle pieces
since i do not trust integrated angle
measurements at all i went for a
variation of a so called fritz and franz
jig with a 30 degree slope
see i'm seeing some plywood made quick
work of accurately getting the angle
done and now i just needed to install a
piece of acrylic which was used to make
it slide accurately and parallel to my
saw plate
[Music]
[Music]
fitting perfectly
nice
after quickly cutting off the excess
wood from the chick i wanted to test it
out and see if i could get an accurate
hexagon
[Music]
and as you can see it worked out
splendidly
[Music]
now for the main project for my cutting
board that i call
these nuts i went with some satin walnut
also called ember wood some european
walnut turning planks as well as some
sweet chestnut
the test pieces i cut had perfect
measurements for my purposes so i
applied the thickness and width to my
solid wood too
then i went over to my trusty bandsaw by
laguna and proceeded to re-saw and cut
my blanks and blank to size
[Music]
and before setting up the fence on my
table saw i had to cut all the pieces to
a 30 degree angle on one side
once done i adjusted my fence such that
the distance between the saw blade
resulted in all sides of the
parallelogram-shaped pieces to be equal
that's what we mathematicians call a
rhomboid by the way
[Music]
this process took quite a while and
could definitely be done more
efficiently by using my miter saw and a
stub block but as mentioned before i
simply want to try out the capabilities
of my new table saw this time around so
i took the time and went through all the
cutting action on this power tool
[Music]
[Music]
next i proceeded to send off a tiny bit
of tarot by hand such that we won't get
any gaps between the pieces one slewing
them together
and then came the most time-consuming
annoying and also hardest part that one
wasn't a pleasure at all to be honest
but it had to be done
after pairing the tires i tried my best
to glue them together i did not have c8
loop back then at my shop so i had to
get creative and use painters tape and a
bunch of little clamps and bigger clamps
to apply approximately even pressure to
all hexagons
[Music]
[Music]
surprisingly enough though that worked
out fairly well and once the glue was
cured i had to remove the whole mess
from the polygons of decrease 6.
that took ages yet again and was the
process that i particularly enjoyed to
be honest
peeling tape and blue off is normally
case pretty satisfying but this one
wasn't it really wasn't everything
sticked together and it was a huge mess
never mind the struggles and let's
forget all the whining here let's get
back to business
getting rid of glue squeeze out at the
corners with a file
i then laid out the pattern one last
time and got to the final glue up which
wasn't as hard as the one before luckily
enough everything slid in place fairly
well
[Music]
next they rolled around and after
removing altered lamps i roughly cut off
the overhanging prisms from one side
such that i could have a reference
surface for my upcoming table saw cut
[Music]
then i had a pretty easy time on my
table saw getting all sides nice and
square by cutting the board to its final
dimensions
[Music]
next came flattening one surface with my
trusty shea poco cnc and after that i
let the opposite side go through my
planner
both tools and combination really make a
quick chop of this procedure and i'm
pretty glad about that
the board still had some tiny gaps where
the glue up wasn't 100 perfect so i
wrapped some tight bond into those gaps
and sanded with an 80 grit without the
random orbital attached to my shop bag
this is very important here this way i
was able to fill all the gaps with
extremely fine wood dust
and to finish all the rough work off i
went over to my router table and
chamfered all the edges with a 45 degree
chamfer bit
[Music]
[Music]
and we are about to be done i finally
send it all the way from an 80 grit up
to a 320 grit
then i water pop the surface with a wet
piece of cloth and sand it again from
180 grit to 320 grit until the surface
was as smooth as steady's hair relax
and here comes the moment we've all been
waiting for let us butter that and
see how the crane is going to shine
also since i'm a foot fetishist at heart
i also decided to add some rubber feet
to this fine individual
and then it was complete here's the
final reveal
[Music]
well i have to say that this one turned
out really well i'm very satisfied with
the result and you can see the 3d effect
quite clearly um if you take a look at
the money shots at the very end yes i'm
very pleased with the result i was kind
of afraid that you wouldn't notice the
3d effect too much just because of the
hard wood of the
amber wood but overall they turned out
very nicely if you're wondering what
that finish was that i was using it was
a mix of mineral oil and also beeswax
it's one of my most favorite finishes
next to
shellac that i also mix for myself so
these are on par
really depends on the on the application
for cutting boards this
cutting board butter you could say is
just absolutely perfect and a separate
video on this mixture is going to come
out in a few days from now once it's out
you can find link down there in the
description but i hope you did enjoy the
video about these nets
i really like the the name of the
cutting board yeah apart from a few
little um
irregularities and also inaccuracies um
i have to say that it turned out very
nicely there are a few things that could
have been done better and more
efficiently for example instead of using
my new table saw i should have used the
miter saw instead so once this goes into
production you can now purchase this
cutting board over on stemming.edu by
the way link down in the description too
um
i'm probably going to use the miter saw
i just want to see
how well the table saw is going to work
for this kind of project and it worked
out very nicely um
also there are one or two other things
that i should take care of next time for
example on the sweet chestnut you're
going to notice that most of these have
the same crane direction going upwards
and
since the grain is so visible on the
sweet chestnut i should have made sure
that um on all the three chestnut um
tiles the crane should be upwards like
for example here there the crane doesn't
move upwards it doesn't bother me but
it's a nice little detail that i should
take care of next time around but i hope
you did enjoy what you have seen today i
hope you learned something new
especially when it comes to this kind of
table saw that i'm using at the moment
and if you didn't enjoy what you have
seen today why not make sure to
subscribe to the channel as well as to
check out stimage.you to support the
channel in some kind of way
i hope you are going to stay safe even
during rona chan and now in the next
video i wish you guys a flammable day
ciao
[Music]
[Music]
[Music]
[Music]
hmm