क्या हम Reverse Forward Starter को बिना Contactor के auxiliary contacts के Interlock कर सकते हैं? और सबसे ज़रूरी सवाल, क्या ये तरीका Safe है? इस वीडियो में हम इसी राज़ से पर्दा उठाएंगे!
इस Advanced Motor Control क्लास में, हम Push Button Interlocking के स्पेशल कंट्रोल सर्किट को explore करेंगे। मैं आपको Digital Board पर step-by-step पूरा वायरिंग डायग्राम बना कर दिखाऊंगा और इस अनोखे मेथड को traditional electrical interlocking से compare करूँगा। अगर आप एक Professional Electrician या student हैं, तो ये वीडियो आपके लिए बहुत ज़रूरी है।
⏰ TIME STAMPS: 00:00 - Introduction: Push Button Interlocking 00:48 - What is Interlocking? 02:15 - Interlocking by using Contactor 04:10 - How the Push Button Interlock Works (Step-by-Step Logic) 14:19 - Push Button interlocking in rev fwd starter 14:55 - Video Course for Electrician 17:29 - Interlocking Diagram by Push Button 21:15 - Final Verdict: Interlocking Method and where to use
📚 Topics Covered in this Video: - Reverse Forward Starter Control Wiring - Push Button Interlocking Explained - Electrical Interlocking vs. Push Button Interlocking - 3-Phase Motor Control Circuits - Industrial Wiring Diagrams - Motor Starter Safety and Protection - DOL (Direct On-Line) Starter comparison
Friends, if you know the control wiring of reverse four starter, then
a question must have come to your mind that when we do
interlocking between reverse four starter,
why do we use only NC contact of the contractor in interlocking.
After all, why don't we do the
interlocking using the push button that is here.
One thing you should know is that we can
also use push button for interlocking here. It has to be
done at many places. Now if we have to do interlocking of push button
then how will we do it? After all,
where will it be used?
We are going to understand all those things through this video.
So hello friends, hello.
I, your friend Arun Gupta, welcome all of you
to this YouTube channel of Electrical Technician. Look friends,
first of all understand here
what is interlocking? See if you are
building a circuit where
you have to operate two devices. But the condition
here is that
only one of the two devices should be running at a time. For example,
your three-phase
induction motor. To run that motor
we use reverse starter.
Why reverse forward?
So we have to rotate the motor in two directions.
So to rotate in two directions
we have to use two contractors. We
will start this contractor. The
motor will run in forward and when it is switched on the
motor will run in reverse. Now here you will
see one thing that the power supply of R Fuzz is given here from this contractor.
But the
blue colored wire is connected in the output
which is going here. And the
power supply of R phase is coming from here to this place.
Meaning, what will happen if I
turn on this contractor here and
turn on this contractor?
From this place the power supply of R phase will
come into it and from this place the power supply of B phase will come into it. This
means that the two power supplies will be connected to each other.
Due to which there will be a short
circuit here. So to prevent this from happening,
we do interlocking between these two contractors here. Even
if you have to do this,
only one of these two contractors should be
operational. No matter how much it is, 100 years,
but our condition itself is such that
we have to start only one of these two at
a time, so there also we have to do
interlocking. Now we are talking about interlocking, so
here I
said that we have to do interlocking using push button.
Before explaining how to do it, let us
understand how interlocking is done using NC contact of the contractor used.
So you will see here we have the
reverse starter control wiring
diagram. In this control wiring diagram,
you will see that when I
press this forward push button here,
what will happen as soon as I press it? This contactor will be my
forward one. And the
NC contact of the forward contactor has been
used here. So the NC contact
here will open directly as soon as it is activated.
And what happened because of the opening
? The circuit broke here. Now if
this contactor is on here, then
no matter how much I press this push button. No matter
how much I press the reverse push button,
my reverse contact will not start.
Ok? Now I have to turn it on.
So what should I do? So
what do I have to do here to turn it on? This
push button here will
have to be pressed. But before pressing it,
it will have to be closed. To stop, you
have to press the stop button. So I
pressed the stop button. All contractors were
closed. Whether it's on or it's
on. Everything will stop.
As soon as you press it. Now after it was closed, I
pressed it. As soon as it is pressed, this
contactor gets activated and as soon as it gets
activated, its NC
contact here will directly open here
and what happens after opening is that
this contactor of mine will remain activated here
and it is closed at the present time. Now let me
press it. If you press it here, the
power supply will go to this place. It will
not be able to go further than this. Why can't he go
? Because here you will see that
my circuit is currently in open condition.
Due to the circuit being open here, the power supply will
not be able to flow further. Because of that this
contactor will not be able to start. Now
it will have to be turned off before turning it on.
Only after closing it can I start this contractor
here. Ok? So
we call this thing interlocking and this
is the interlocking diagram of reverse over starter. Now here I have to do interlocking using this push button.
So let
me take a small example to explain to you the interlocking using push button in an easy way.
At this time, you should understand that I have
given phase supply to the push button
and have taken its output and
connected it to the light and have
given neutral supply directly to this light.
Is this much clear? Now understand, at this time,
what is this push button that is installed here? It is an element.
So what is the element that is placed here
? There is anno contact. What will Eno Contact
do? It will not allow the power supply to flow further
if we do not press it. But
as soon as I press this push button here,
what
happens as soon as I press it? Our power supply here will
flow forward and the power supply will go to this place. The
neutral supply is
coming directly from here due to which the
light is on here. So, to turn it on,
when we press the push button, the
light should turn on as soon as it is pressed, so
what will we have to use here for this? We will
have to use Ano Contact here.
Ok? You must have understood this much. Now
let's move ahead. Look, I just
took a single light. Your reverse starter has
two contractors, right? So,
at the place of light, you should consider yourself as a contractor. I am
giving an example right now. So I am
taking the light. So now look, I have
installed two lights here. Now
we have to keep conditions in both the lights. What is the condition
? The condition here is that if I
turn on this light, then
this light here should not turn on for any reason.
I want this light not to turn on when I turn it on. So what
should be done? Think a little and
tell us by commenting in the comment box. Come on, comment.
I also need to know a little answer as to what all
things you know.
According to that, whatever videos I make in future, I will
make them according to that so
that I can give you better knowledge in more detail.
Ok? So comment that if I have to
turn it on by pressing this push button
and if this light is on then in that condition
this light should not be on for me. If
I want to do this, what do I have to do here
? See, the answer to this is that I will have to
install something here with this push button so that if I
press this push button, the
circuit of this bulb,
this circuit, gets opened here and
what will have to be done to open it? Do we
have to use NO or NC for this push button here
? Please tell me a little about this also by commenting.
I want to know the answer. Please
comment, really. Ok? So now understand
that I am taking the push button here.
It has to be turned off through this push button. There
is no second condition.
It should not start when I press it.
This is what is being said. So in this condition,
I will have to do something with this push button
so that by pressing it the
circuit gets opened.
What do you need to do here to do this? Which
is your push button here. What will you put on the element that you place on the side behind this push button to
activate the circuit?
You will put anno contact here. Now the
circuit has to be closed here also. So to turn it off,
you will have to place another element on the side or above this push button.
What is an element? One is an ANO
element and the other is an NC element. So at
present there is NO here.
NO is installed here also. Now we just have to add another element here
just below or on the side
and
our element should be NC here.
Why are you using NC?
Because after pressing it here,
some other circuit has to be closed. The power has to be turned
off. Understand here
what will happen if I use NO?
When I press this it will close
and what will happen if I use NC here
? If I do not press the push button, the
power supply will continue to flow.
But as soon as I press it, the
circuit here will
open and due to it being open,
no power supply will flow further.
So we have to stop the power supply. So
to stop it, NC element will
have to be used. This much thing has become clear. Okay,
fine. Let's move ahead. Now see
what should I do here? Now I will place the
NC element below or on the side of my push button.
One will remain N and the other will
remain NC. I have done so much work. Now
after doing so much work, you will see here that
this is installed below my push button. Now
here I want that when I
press this push button,
my light should turn on as soon as I press it. Excellent.
We can do this. Its wiring
is already there. You will also see here that the Ano push
button has been given power supply
and this light has been given its output.
So when I press this it will
start. Now after this it has been said
that when you press it, this light should
turn on but this light should not turn on.
If it is kept pressed and if
it is pressed in that condition then this light should not turn on,
we want this here. So
what do we have to do here for this? The
power supply that will go to this bulb from this bulb does
not have to be taken directly. We have to take it
around a little bit. From where?
So from this place, turn the wire and bring it to this
push button. Where did you bring it from? This one
in the NC contact of the push button. And
from this place the power supply will go back to this place.
Meaning that the
power supply which was going directly, we will now
take it here in a roundabout way. What will be the benefit of doing this
? Understand. You will see here
that our push button is, do not press it right now.
I haven't pressed it yet. Right now
I just press this push
button here. As soon as you press this, the
power supply will rotate from here and come here.
Due to which the light turns on.
Great, this light is turning on. Now
understand here that if I press this push button. I have
pressed this also.
I pressed this and pressed this also.
What do you think? Will this light
stay on here? Tell me. Please comment.
Let me understand a little bit
how much I understand you. Ok? I
commented. Excellent. Now look here, you understand
that if I press this,
what will happen after pressing it? The power supply
flowed from here and reached this place. And this
is NC. So NC will provide power supply further.
But at present I have kept this also
pressed. So
what has happened to NC contact because of pressing this
? It is open at this time and
because of being open, do you think the
power supply will come here or not, so the power
supply is not able to come here
due to which this light of mine will remain off, but the
power supply to this light is
coming through its ANO contact, so the
ANO contact will give the power supply forward
due to which our light will turn on, now this
thing is clear, it was great, it was fun,
let's move ahead, so
what did we do in the circuit that we made at this time?
We interlocked this light here through this.
Can you say that what will
happen in the wiring that is here
? When we just press this push button,
this light will turn on and when we press this push
button, this light will turn on.
But here if we press and hold this push button,
this light turns on.
So in this condition, if we try to turn on this light, then
this light will not be
able to turn on. Because through this push button
we have interlocked the circuit of this light. Is it
clear? Did you enjoy it? Let's
move ahead. Right now I have
done single interlocking here. What did you do just now? Interlocking
this circuit only through this push button.
But in reverse little
starter we have to interlock both the circuits,
right? One
should be on at a time. What happened here? There was single
interlocking, so if this one was on
then this one would not be able to start. It is like that. Interlocking was done in
this manner. Now it is being said that
if we start it then it may not start
and if we start it earlier then it may not start.
We need a circuit like this. So in this condition
we will have to do another interlocking here.
Which interlocking will come now? So
understand that here we will have to
install NC contact below both the push buttons. And after installing the NC contact, the
power supply will
go to this light through this push button. But the power supply will
not go directly. You have to take it around here
and give it to this NC contact.
And the power supply that will go through this NC contact will go to
this light.
What will happen with so much wiring now?
If I press this push button,
this light will not turn on. Ok?
But if you leave it, then
this light will turn on when you press it. Now I have to do something else here.
What I want here is that
if I press this push button,
then this light should not turn on in this condition.
So to do this we will
have to do interlocking. And
what will be the interlocking that we are going to have? The
power supply which was going to go directly from this push button will
no longer go directly. It will
come around from here to this place and
from its output,
power supply will be given to the light here. This means that its
output will be given to this NC contact and
through this the power supply will be given to this light.
Is it clear? Did you understand? Ok?
I do one thing to make this thing look simple.
You understand that the power supply will go into it from here, so
from here I have
given power to the light at this place and from this
place I have given power supply to it. Now
I want to press this so that
my light gets turned off. I can make the symbol of the
NC contact fitted on this push button here to
explain it to you. So let me create this NC contact
here like this and write
its name, what should I write? This
is our NC of Second Light. So let me
write here that NC of second light has been
used here. of the second push button. So the
NC of the second push button is used here.
And the NC of the first push button will be
used here.
What do you have to do in this place? The
NC contact of the first light has to be used. The
interlocking is done. Got the wiring
? It's very easy, isn't it? What did you do? I
put the NC of this push button in the middle of the power supply going from this push button
and put the NC contact of this push button here in this circuit, that's it, the
interlocking is done, now understand that I was
connecting the light here, if the
contact comes at this place then how will you do it, it is the same thing, there is
no difference, you have to do the same thing,
here you can see that my device is a
starter, here you will see that I have
a motor, to run this motor in reverse forward
direction, power wiring has been made
and control wiring has been made
but there is no interlocking here in the control wiring.
Earlier I showed you
how you would do it if you wanted to do interlocking of contractor.
But now we do
not have interlocking here. We do not have to do
interlocking here using a contractor.
Whose job is it to do?
Interlocking is to be done using push button. Now
before telling this, friends, I would
like to tell you that if you
want to take electrical training from us. Like when you
go to the industry,
no one teaches you any work there. You have to work on your own. Only
then do you get knowledge.
Your senior supervisor does not teach you quickly.
So in this condition, you can gain
good knowledge by joining our video courses.
If you
want to learn about motor starter here.
Like right now I am
teaching about reverse power starter. And
if you do
not know about the power wiring control wiring of reverse power starter
, do not know about star delta starter
, do not know about DO starter
, then you can join this class. The
fee for this class is only ₹300.
I am going to provide you complete proper electrical
training here for less money than what you spend on partying. Now
if you join this class,
after one month of joining, I am
also going to give you a certificate here.
Course Completion Certificate. So if you
want to learn this thing then
join the class. I have given the link of the class
in the description of the video.
Now look friends, understand one more thing here.
You can see this class in two
ways. First thing,
go to our website here on Google.
There you search for wiring school. If you
search for wiring school, our
website will appear. You will click on this.
After clicking, courses are written here.
Click on this and
after clicking on courses, go to paid courses.
Then there is a video course here. You have to click on this.
After clicking, you will
go here and join whatever class you want.
We have a lot of classes. For example,
if you want to take engineer level training
, then join this class.
If you want to learn to read drawing then
you can join this class.
We have many such classes.
You can check it here. Ok
? So whatever class you join,
you can directly come here and watch the class through our website.
Apart from this, if you
want, you can go to our app on Play Store.
Go to Play Store and
search for Electrical Technician app there.
You will find our app here. If you look at this app,
more than 50,000 students have
downloaded it. Plus, there are 437
reviews here in which we have got 4.8 stars. If
you want, you
can read the review here.
What do the students say about us? So this is our app,
you will have to download this app. You will
have to log in inside it. After logging in,
you can see all the classes inside it.
Plus, if you want, you can also join classes from within this.
Ok?
I have given the link of this app plus the course link in the description of the video.
From there you
can join directly by clicking and download the app.
Plus my mobile number is
written here. You can contact on this number anytime.
Okay friends? Now
let's come to our class topic. So
here in our starter we have to do
interlocking. How to do it? Understand.
Here we have a push button,
when I press this push button, this contactor should
not be on.
I want this. So what should I do in this condition? I will
use the NC contact of the push button here.
Now to identify it, it is
written here that there is a push button of F Start here.
So what will happen here?
Our push button with F, its F is
start and here I can write NC. That
means I have used the NC of the forward start push button
here.
What will happen if you use it like this? If
I press this push button then the power
supply will come from here forward contactor will turn on.
And what will happen here as long as I keep the push button pressed
? It will
remain open. And because it is open, if I
press it, the power will not be able to go from here.
And it will not be able to start.
Is it clear? First thing. Now if I release this,
what will it be? NC will be formed.
Meaning that the circuit has become normal again.
Look at one thing here. As soon as it was released, it
became NC again. What happens if I press it
? The power supply will go into it
and it will turn on. So here
you understand why we do
not do interlocking of the push button here. In the reverse
forward starter,
we want that
if I press the push button once, it starts
working. So let this continue.
After that, no matter how much I press it, this
contact will not start. To do this,
we have to interlock the PE contactor with the NC
contact.
But at present, we use the
NC contact of the same push button that we are using for interlocking.
What happened due to using NC contact of forward start?
It will open only when you press it.
After releasing it became normal. Now if I
press this, it will turn on.
So what? This was already going on.
Along with this this also started. Meaning there are 100
circuits. So 100 circuits are done
but now if you want to save this thing
then you can do one more thing. The
interlocking of the push button that was here was
done here, so do the interlocking of this push button here.
Meaning, put NC contact here
also and whose NC will this be? The
NC contact of the reverse start push button is going to be
here. Now
what will happen if the wiring is done in this manner?
What if I press it? You turned it on
and by pressing it,
this circuit got opened, right?
This cha will remain open as long as I keep pressing it. So
if I press this, it will not allow it to start
because it is open. But as soon as I
leave it it will become NC. Now if I
press this, this
contractor here is activated. But
as soon as I turn it on, I will turn it off.
Turned it on but turned it off.
How did you close it? Because when it is pressed,
this NC contact opens.
Due to opening the power supply got cut. Due to which
our contractor will be closed.
Is it clear? So what is happening here is that
if I keep one on and
press the other push button then the other one will turn on.
But the first one will
close the circuit. So if you want that when you
press one push button, it should
turn on that circuit but
turn off the other circuit, then in this condition we
will do interlocking of the push button. But if
you are told that only one
device should be running at a time. If you press this push button, the
contractor will start and this
contractor should run until you switch it off.
In this condition, you will have to
use the NC contact of this contractor
so that
it remains open as long as it is on, it is not that it should
remain interlocked till the time the push button is pressed.
This contractor should not be activated until this
contractor is activated, for this
NC of this contractor has to be used. In the
same way, you will do interlocking by using the NC of this contractor here.
Ok
? So you must have understood the concept
that how will you do the interlocking of the push button
and if you do the interlocking of the push button
then where will you do it? Let me explain it once more and get it
revised again.
Simply understand that if we have to do
interlocking of push button, then
we do its interlocking at such a place where
if one of our circuits is on and
in the condition of that circuit being on, we
want to start the second circuit but as
soon as the second circuit is on, the first circuit gets switched
off, then in this condition we will
do interlocking of the push button. Second thing, if
you are told that you have to
build a circuit here where there are two
contractors and two devices.
If one of the two devices is running
then the other device should not be on under
any condition until we switch
off the first device, in this condition
you have to do interlocking using NC contact of the contactor. Ok
? It must have become clear. Friends,
before ending the class, I would like to tell you
that our app on Play Store,
Electrical Technician App, please
download it and check it out once.
You are going to get a lot of help
through that app. Plus
I would like to tell you that if you
want to read electrical knowledge books then we have two books for you. The
first one we have is a house
wiring book called Zero to
Hero House Wiring Book. The second is the
Electrician A to Z Wiring Book. You
can increase your knowledge a lot through these two books.
If you do house wiring work then
buy a book on house wiring. And
if you do industrial work, then
this book is important for you.
Along with this you can also take this book.
Because there are many concepts
like about submersible pump,
about ceiling fan, you get all that knowledge
in this book. So,
for industrial students, both the books
are important and for house wiring
students, only the house wiring
book is important. So if you want to get both these
books delivered to your home, I have
given its link in the description of the video. Apart from this, if you want,
you can also buy the PDF of this book.
I have given the buy link in the description. Ok
? So let's end today's video here.