It's time to get trains running again on the On30 Thunder Mesa Mining Company layout! In this installment, I wire new and old parts of the layout for reliable DCC operations, then add an auto-reverse unit to control electrical polarity on the new wye in a way that's quick and easy. Frog Juicers from Tam valley Depot are added to provide uninterrupted electrical power to all of the turnouts and, last but not least, I hook up a wireless throttle from NCE to power the layout cable-free. It feels great to have trains running again on the old layout!
Become a Thunder Mesa Member on Patreon for early access, exclusive content, and members only parts and details from the builds! https://patreon.com/thundermesa/
All music courtesy YouTube Audio Library, Creative Commons License.
[Music]
Howdy folks. Dave here at Thunder Mesa's
studio and this week going to be working
on the 30 Thunder Mesa Mining Company
layout. I want to pick up pretty much
where we left off last time and bring
some power to the rails we laid in the
new section, wiring everything up for
reliable DCC operations. As you can see,
I've been having some fun placing
structures and details in place, trying
to figure out where everything's going
to go on this new section. But right
now, I need to take a lot of this stuff
off so I can proceed with the wiring and
get trains running again on the Thunder
Mesa layout.
One of the great advantages of rejoining
the Thunder Mesa layout with the
Goldfield and Calico is that now I can
operate both layouts on the same DCC
system. I can use separate throttles,
but it's all basically the same system.
And I'm using an NCE power cap or main
layout power. My plan here is just to
continue the DCC bus from under the
goldfield and calico through the new
section and into the older sections of
the Thunder Mason Mining Company layout.
Basically electrically unifying the
whole thing, though I can operate them
still as different layouts with separate
throttles. Of course, there are always a
few complications, a few wrinkles to
make projects like this a little bit
more interesting. And the biggest one
here is that I need to power this Y in
such a way that I don't short out the
entire system. This is a reversing
section. So, we've got some polarity
issues there with the plus going to
minus and the minus going to plus. And
at the same time, I want to bring power
to all of the frogs for all those new
turnouts that I installed last time. And
I've got a product coming from Tam
Valley Depot, which is really going to
help out with all that and greatly
simplify all of this wiring. But, uh,
let's cross that bridge when we get
there. Right now, I want to go under
here and run that DCC bus. Okay, I've
tapped into the DCC bus under the
goldfield and calico
and run the 14 gauge wires out through
this halfinch hole I just cut through
the fascia here. And these will now
connect to the wiring bus that's going
to run under the entire Thunder Mesa
layout. Just need to strip
a little bit of insulation off the end
of each one of these
because I'm using these locking terminal
connectors
between the different sections of the
layout. So, if I ever need to move it
again, it'll be uh much easier to
disassemble.
And I like to use this heavy
14 AWG stranded wire for my DCC bus
because remember it's not only carrying
uh the electrical power but it's also
carrying the digital signal for the
locomotives.
And I want to run this bus
directly beneath the rails of the main
line as much as I can.
So I've drilled some quarter inch holes
through these uprightes here.
Well, I think I'm going to
run an entirely new DCC bus under the
original Thunder Mesa section as well.
I'm looking at it under here and it's
honestly it's a bit of a mess and uh not
up to my current standards. So, I'm
going to redo it while I'm down here.
All of this
must go.
Well, this has been a fun bit of model
railroad archaeology digging under here.
Um,
I wanted to save some of the feeder
wires coming down from the rails.
Uh, but it's kind of hard to figure out
which rail they go to because when I
originally wired this, I used black
feeder wires for both rails,
which is something I would never do now
because it makes this kind of job a lot
harder. Uh, but now I figured it out and
I'm marking them, you know, black and
red with a piece of tape so uh I can
reconnect them when I put the new DCC
bus in. Live and learn.
You go away.
Okay.
Shiny new wire going in.
And now I have a red Sharpie and a black
Sharpie. And I'm going to go around here
on the roaded and mark where I want to
drop feeders down from the rails to that
DCC bus. And the funny thing is, if
you'd asked me a week ago
which was the outside and which was the
inside rail, I would have said I always
put red as the outside rail and black as
the inside rail, just like I did on the
Barllo Pass layout. Well, I just uh came
to realize on the Goldfield and Calico,
I switched them. So, black is the
outside and red is the inside.
It doesn't matter as long as I can keep
it straight.
So the idea is to
basically have feeder wires for every
section of track approximately every
three feet.
And that way, uh, there's no
interruption in the power or the DCC
signal, and we're not relying on things
like rail joiners and turnouts to, uh,
to keep the power flowing through the
rails.
The engine house track will have its own
dedicated feeders.
On these pico turnouts, you always want
to run the power from the point end down
here, never from the frog end of the
turnout. If you run the power from the
frog end of the turnout, you're going to
get a short circuit in here. And that's
why we put insulated rail joiners on all
of these connections right here. And
we've got a separate wire that is
soldered to the frog, which is
appropriately green, as many people
pointed out in the last uh Thunder Mesa
video. Um, so I've got this little
section of track here between these two
turnouts, and that's where we need to
connect the feeder wires for the DCC
bus.
Now things start to get a little bit
interesting when we get over to the Y.
Here we've got our outside rails marked
in black. Outside
outside
over here.
But what happens when these converge on
this point up here? Well, suddenly
this becomes
the outside rail
and this becomes
the inside rail. So, think of it in
electrical terms. This is negative and
this is positive. All of a sudden, you
know, positive going to negative and
negative going to positive. That's going
to cause a short circuit.
The solution is to isolate one of these
legs coming off of the Y electrically,
completely isolated electrically and
then have a way to switch the polarity.
And so I was originally going to use
this section down here down that way,
but the wiring in that is a little bit
more complicated than if I just use this
section going into the tunnel up here.
So that is going to be our reversing
section. I've already got insulated rail
joiners in here. And now we just have to
wire it as a reversing section.
So rather than mark this red or black,
I'm going to mark it with an R
on both rails. So now I can wire all the
rest of this normally until I get to
that reversing section back in the
tunnel. Now I need to drill some holes
down through the roaded and the
subroaded. every place that I put these
arrows. I'm using a 764th
drill bit, size drill bit. Uh, and
that's just the right size for the 22
gauge feeder wires that I'm going to be
using. I want to get right up as close
to the rails as I can without damaging
them.
[Music]
Now, if you watched my recent video on
wiring the HO3 barlo pass layout, some
of what I'm about to do next is going to
look pretty familiar. But it just goes
to show that, you know, it doesn't
matter what scale you're modeling in.
These techniques, these skills still
apply. One thing I didn't show in the
Barllo Pass video is uh cleaning the
track before soldering on the uh the
feeders.
And that's a pretty important step
because one of the secrets to a good
solder joint and a good strong
electrical connection is to make sure
that all the adjoining parts are very
very clean.
This is particularly true in this case
where I'm using recycled track. So, I'm
going through with a Q-tip and some
odorless mineral spirits and getting the
paint off of the sides of the rails
where those solder joints are going to
be. You can see that gunk coming off
there. By the way, if you use mineral
spirits for anything, uh don't pour it
in a plastic container.
Use a glass or a metal lid like I'm
using here, uh because it'll eat the
plastic.
And you don't want to pour it onto the
rails for the same reason because it
will eventually eat through those
plastic ties.
You also want to remember that mineral
spirits are highly flammable. So take a
lot of care while you do this and make
sure that they evaporate completely or
completely wiped off before you touch
the rails with a hot soldering iron.
Now for those feeders, this is some uh
22 gauge solid core wire.
And I want to strip off about
38 of an inch of the insulation.
Put it down through my hole.
Then I'm going to bend this wire into
Lshape like that.
And then use the springy action of the
wire to hold it in place
uh in the webbing of that rail I beam.
If it doesn't hold in place against the
rail, you've pulled too much wire down
in there. Just give it a little slack
back up in there and make that little
loop like that.
Then using some 60/40 rosin core lead
solder and a good hot soldering iron,
heat the connection here where the rail
and the wire touch.
Heat that up for just a second or two
and then
hit it with the solder.
You know you've got a good solder joint
when it's nice and shiny. If it looks
dull, uh, that's what's called a cold
solder, and it's not going to hold and
it's not going to conduct electricity
very well. Once that cools a little bit,
pull the wire down through the hole
until just about all that's sticking out
is the stripped portion of the wire and
you can't see the insulation. And then
once this is all painted and ballasted,
it'll be really hard to find these
connections.
Sometimes the far rail can be a little
challenging.
Learn how to work upside down and
backwards.
Then down here underneath, I'll be using
these Scotch lock connectors to hook the
feeders up to the DCC bus. These just
slide onto the larger wire, that 14
gauge wire.
And then you feed
the smaller wire, the 22 gauge wire,
into this upper hole. And for those of
you who've worked on cars, I know this
is nothing new. And then you
crimp that with a pair of pliers.
good and hard. Then you fold that down
and it's locked.
No stripping, no soldering, no fuss, no
mus. Pretty easy.
By the way, if those don't lock easily
into place, uh, that might mean you need
to crimp that down a little bit more.
Just give it a good squeeze with the
pliers. It should snap easily.
On a DCC layout like this, there's
really not much reason to do traditional
block wiring like you would do on a DC
layout where, you know, you've got
individual blocks that are powered by,
you know, toggle switches like this one.
And that's because in DCC, it's the
digital signal that controls the
locomotive. So, you can have multiple
locomotives going in different
directions on the same track if you want
to. However, there are special instances
where you might want to do that uh to
add a block, and this is one of those. I
want this enginehouse track to be a
separate block so I can turn the power
off to this track. I don't necessarily
want to have power running to this track
all the time when I've got locomotives
in the engine house or whatever when I'm
running the rest of the layout. I just
want the option to be able to turn it
off and on. So, going to interrupt one
of the wires between the track and the
DCC bus with a single pole, single throw
on/off switch. I'll connect the uh red
wire to the bus as usual,
but this time the black wire will go to
one of the terminals on this little
toggle switch.
And then a second length of black wire
gets connected to the other terminal.
And then this end goes to the DCC bus.
So we've created a little break in that
circuit with an onoff switch. So I can
turn the enginehouse track on or off
depending on how I want to operate it.
And eventually there's going to be a
whole uh this will be all where all the
controls for the layout are going to be
located for the most part. So, just
putting this toggle switch here now in
anticipation of that. And I'll just
mount this in place here temporarily
with some of this uh 3M industrial
strength double stick foam tape.
That'll be a good reminder to get that
control panel done.
Now remember, every leg of the Y gets
wired normally except for this one back
here from these insulated rail joiners
back. That's going to be our reversing
section.
Well, I'm making the last of the
straight connections. That is the
nonreversing section connections
here under
Geyser Gulch.
This is kind of momentous.
Pretty soon the Thunder Mesa layout will
be running again.
It's been a long time. It's been too
long. I have missed it.
Really hope I guessed right on which
rail these wires go to. Guess I'll know
in a minute. The next thing I need to do
to make this Y operational is have a way
to switch the polarity on this isolated
section of track I've laid back here.
The easiest way to do that on a DCC
layout is with one of these automatic
polarity reversing units. This one is
from MRC, Model Rectifier Corporation,
though there are other ones out there.
And what they do in a nutshell is they
detect a short circuit on that isolated
section of track. Say your locomotive
comes on from the other direction and
this one the polarity is reversed. It's
going to detect that short circuit in
just milliseconds and switch the
polarity of that section of track before
it can short out your whole system.
Great little invention. Super easy to
hook up. And that's what we're going to
do right now on this MRC unit. The
yellow wires go to the rails. And we
don't need to worry about which side is
which in this particular case.
This little unit doesn't need to be up
on the control panel or anything.
does all its work behind the scenes. So,
just going to mount it right here
to the bench work.
And then the red wires get hooked up to
the DCC bus.
And again, it doesn't matter
which one is which.
Just got to make sure this wire
that's coming in is pushed all the way
in
so you get a good connection.
And now it's time to juice all of those
frogs. And no, I don't mean in a
blender. That would be gross. No, of
course I'm talking about juicing the
frogs on the turnout. Bringing
electrical power to this thing right
here. That's the pointy part where the
diverging route and the main route of
the turnout come together. And this
little board right here is what's known
as a frog juicer. Got this from Duncan
McCrae over at Tam Valley Depot. He's
got a lot of amazing stuff on his
website. I'll put a link below. You can
check it out if you're into Model
Railroad Electronics. You'll be a kid in
a candy store down there. This is a six
frog unit. He calls it the Hexfrog
juicer. And you can see it's got one,
two, three, four, five, six terminals up
here that we will be attaching the green
wires from those frogs to. And then here
is the uh the DCC in right there, which
will connect to our DCC bus right there.
This works in very much the same way as
that u polarity reversing unit I just
put in in that it it detects it uses
microcurren to detect uh a short circuit
and then within milliseconds switches
the frog polarity to match the direction
uh that that the uh the power is
flowing. makes operations so much
better, so much more pleasant when
you're not having locomotives stall on
the frog. Especially if you run a lot of
short wheelbase locomotives like I do on
the Thunder Mesa layout. Uh this is this
is a mustave in my opinion. Even though
these pico turnouts are great, um, you
know, once you start to paint them and
balance them and things like that,
you're not going to have reliable
electrical power coming to these closure
rails all the time. So, this solves that
problem. Can't wait to get this
installed and see how things run. But
before I show you how I wire these up,
let's hop in the wayback machine so uh
we can have a little review on how I
hook the wires up to the turnout frogs
in the previous episode of the Thunder
Mesa build. You know, because these Pico
turnouts, they don't come this way. I
use Pico30
track and turnouts throughout uh the
Thunder Mesa and the Goldfield and
Calico layouts. if you plan to have uh
polarity routing here from the frog, say
from a frog juicer or or something like
that or switch machine, and that is to
connect a wire to the frog. The nice
thing about these Pico turnouts is you
can solder this wire basically anywhere
on the frog and get the same result
electrically. So, run this up through
here.
That should do it. Well, now that we're
all up to speed, the only remaining
question is where do I put this thing?
Because this can go just about anywhere
as long as it's not too far away from
the turnout frogs that it's controlling.
Uh, it can go underneath the layout,
hidden away. It can be part of the
control panel. Um, I think what I'm
going to do is mount it right here for
now. Our little impromptu control panel
here. Little temporary control panel.
And that way you'll be able to see uh
how everything hooks up and uh how it
works.
This has four screw mounting holes. I'm
just going to use the top two for now.
Nice feature is it also has rubber
bushings on the back
so you don't have to uh worry about
screwing this in too close to
your control panel or the board or
whatever
and damaging those electronics.
The first connections I want to make are
to the DCC wiring bus. And once again,
I'm using the the black and red 22 gauge
wire here, but
um in this case,
it doesn't matter which is inside and
which is outside.
Just uh trying to keep things pretty and
consistent for the most part.
I'm going to start with the frog on this
turnout over on the Goldfield and Calico
that connects to the Thunder Mesa
layout. I've run the green wire from the
frog down underneath the benchwork out
here to the frog juicer.
We're going to call that one frog number
one.
Number
two is coming from this first turnout
that will go out to the wararf.
And the next one comes from this turnout
going into the Y.
And then the one from the uh enginehouse
spur.
So just going down the line from right
to left. This is number five from
the Y turnout back at the tunnel portal.
Always want to give those a little tug
to make sure you've got a good
connection.
Last one, number six.
That's from this turnout in front of the
depot.
Now, before I power everything up, I
want to let you know that I have been
testing all of the components and all
the connections as I go along with a
multimeter. That's a very important
thing to do to avoid damaging your
equipment. Okay, switching on. Here goes
nothing.
Now, I'll give the track a very thorough
cleaning and we'll test everything out
with a locomotive. Okay, I've got
locomotive number four up here on the
enginehouse track. This is a Bachmann
440. It's one of my favorite engines.
And the plan here is just to run it
through all of these turnouts and uh
change directions on the Y. So when we
come back, we'll be facing the opposite
way.
[Music]
[Applause]
Heat. Heat.
[Music]
Heat. Heat.
[Music]
Heat. Heat.
[Music]
[Music]
Heat.
Heat.
Heat.
[Music]
Heat.
[Music]
Heat. Hey, heat. Hey, heat.
[Music]
Look at that.
Facing the opposite of the way we
started.
I love it when a plan comes together.
As the locomotive moves through all the
different turnouts, these indicator
lights change when the polarity switches
on those frogs. So, you can see that
everything is functioning. Also need to
test my switch to the engine house
track. Right now it's in the on
position.
And now when I give that locomotive a
little steam, it should not move.
Oh, no signs of life.
Everything works.
But wait, there's one more bit of
technological wizardry I want to show
you before we wrap up today, and that's
how to hook up the NCE PowerPro wireless
cab to the Power Cab system. I haven't
used this wireless cab in over a year,
so I'm putting some fresh AAA batteries
in. This wireless system has has two
components. You've got the wireless
transmitter with the antenna sticking
out and you've got the uh the power pro
cab and the flat cable coming out from
the uh from the transmitter. This is
going to hook up to that panel uh where
the uh power cab hooks up. Here on the
NCE panel, you can see that there are
two jacks here. One is for the power cab
itself and the other one is for an
additional cab or in this case um the
wireless transmitter. So we just plug
this in
like so. I'll find a better spot for
this transmitter in the future. Maybe
behind the backdrop or something. But uh
for now leave it right here to test
things out. And if I'm remembering
correctly, the way we power this on is
by pressing and holding the horn button.
There it goes. Next, I want to make sure
I have the proper locomotive selected.
So, I hit select and then the number for
the locomotive. In this case, it's
number four. Okay. And you've got your
indicator light here that says it is in
the forward direction position. Want to
change that to reverse.
There we go. Now the little red light is
over the R and we'll give it a little
throttle.
There we go.
Works like a charm. I really enjoyed
using this wireless cab on the old
version of the Thunder Mesa layout and
I'm looking forward to using it again on
this new version that I'm working on. It
makes operating the layout so much more
fun. You don't have to worry about
plugging in cabs into panels around the
layout and moving them around. You don't
have to worry about tripping over cords.
You can move around the whole layout.
And uh the only downside is that um
sometimes I would misplace this thing
and forget where it was. So I got to
keep an eye on it. But that's going to
wrap it up for this one. It feels like
we covered a lot of ground. Got a lot
done. Trains are running again on the
Thunder Mesa Mining Company layout. And
that is exciting, at least for me. Thank
you all so much for watching today. I
hope you enjoyed the video. I'll be back
next week with another installment of
the Thunderbird Route 66 themed layout
that I'm working on with Gary Batty and
I hope you'll tune in for that. I hope
you're subscribed with those
notifications turned on so YouTube will
let you know when the next video is
coming from Thunder Mesa Studio. And in
the meantime, you know, you can also
follow over on Patreon for free. That's
patreon.com/thundermesa
or become a paid member if you are moved
to do so. You can also follow on
Instagram at thunder.ma and check out
the resources available on the thunder
mesa studio website. That's thunder
mesa.studio.
As always, a great big thank you and
shout out to our Patreon members who
make these projects and these videos
possible. Until next time, keep moving
forward everybody. Adios for now.
[Music]
Heat.