We take you inside Raptor Mining's massive 100,000sq ft shop to show you how they rebuild some of the largest buckets in Mining! From rope shovel buckets on P&H 4100/Cat 7495 to hydraulic mining shovel buckets on Cat 6040 and Hitachi EX5600, we take you behind the scenes and show you the process for rebuilding, repairing, and welding, buckets and more!
In this video you will learn: How massive mining buckets are rebuilt and repaired The process of rebuilding Cat D11 track frames How robot welding machines are used What ground engaging tools are and how Raptor armours them with welding overlay
So today we are at Raptor Edmonton at their CISC or Continuous Improvement Service Center.
We are touring the shop to show you how they rebuild buckets like this, a 59 cubic yard
rope shovel bucket off the Viserys Erie or Caterpillar 7495. So stay tuned to learn all
about how they rebuild buckets like this, some of the wear product that Raptor makes,
such as the LWP up there, and how they rebuild track frames and more.
So behind us here, this is where Raptor started back in 2005. So Craig ran this out of his garage
for almost two years. Yep, almost two years. And you have to start somewhere. You got to start
somewhere. Yep. So Raptor started here and as you're about to see today, we're going to take
you inside their large CISC in Edmonton, which is their Continuous Improvement Service Center,
where they build new buckets, rebuild buckets, do GET, wear product, track frames for dozers,
everything. So this is where it started right here back in 2005.
So this is a 59 cubic yard rope shovel bucket off a Caterpillar 7495 rope shovel. Buckets like this
come here to get repaired at Raptor. So basically the bucket gets sandblasted by an outside source,
comes here, Raptor will do NDT testing or non-destructive testing using magnetic particles,
so magnetic testing. So they look for cracks in the bucket. Any cracks they find, they gouge out.
They'll then test to make sure that the crack is gone, repair the crack by welding it, and then
they'll go through and install wear products such as Raptor Plate or Harder Plate. They'll install
G.E.T. such as this here. This is Esco's Nemesis G.E.T. So we've got tooth, adapter, and lip shroud.
So that's some of the G.E.T. that this customer wanted. There's the Esco Nemesis, or you can run
a Caterpillar Weissler system. So this is Raptor Plate. As we mentioned, Raptor builds their own
wear product. So if you ever need to identify Raptor Plate in the wild, these little zigzag
patterns is a signature identifying trait of Raptor Plate. Raptor Plate is a chromium carbide
overlay, so really good protection at sliding wear. And when it wears, it polishes up beautifully
because it has chrome in it, and these zigzag patterns will become very apparent. So in this
rope shovel bucket, they line the bottom of the bucket where all the material is passing over.
So over the lip, across the bottom of the bucket, and through the trap door.
So Raptor does what's called laser scans on these. They scan the bucket with laser beams.
When they're trying to model the wear product in which they're going to use to line the bucket,
they'll scan the bucket so they can determine how much they need to actually model and build
the package. So in the old days, they used cardboard. So you can imagine getting a big
piece of cardboard and lining it up and then taking that to the engineer, but now they use
laser beams. So they scan the bucket, they can get an idea of how much they need, they get a
model of the bucket, and then in addition to that, once they've installed the wear package,
they can scan it and get a true surface, a zero percent wear, and then as the bucket's worn,
whether that's 5,000 hours or 10,000 hours, depending on the application, they can scan it
again and they can get an idea of where the wear is occurring, so a heat map. So if the bucket's
wearing out on the heel or on the tip more, Raptor can better tailor the wear package to that and
they can also replace what needs to be replaced and they get a better understanding of how the
bucket is reacting, how the bucket and the wear product is reacting to the material, the application,
the operator, the mining operation as a whole. So as we've seen earlier, Raptor rebuilds buckets,
but this is one of the buckets that Raptor builds in-house. So this is a Raptor branded
dipper bucket. So they're currently building it here, and as you can see, all this bracing
is a Raptor customized and engineered brace because when you're building these buckets,
they don't build it all in one, they build it in pieces. So the bowl, as we'll see on the
dipper bucket, is over there, but this is the top of the dipper bucket, so when they weld it,
they want to have it braced so that there's no changes in the structure, so that the two surfaces
on the edges here made up perfectly when they combine the bucket pieces. So this is how Raptor
builds buckets. It's all customized steel with custom bracing to build a bucket that'll hold
60 cubic yards and go on the end of a rope shovel. This is the bowl, so this is the other half of the
dipper bucket, and as you can see in here, we've got, again, gussets or bracing to prevent any
flexing or change in structure to the bucket when it's being built. Once the two pieces are
complete, they'll be combined and you'll get a dipper bucket.
This is a bucket off a CAT 6040, so another example of some of the buckets that Raptor
rebuilds here. As we touched on earlier, you can see some of the white markings here, that's their
non-destructive testing, metallic particle testing, so that's where they look for cracks
using ferromagnetic particles that line up on gaps in the electric field when you magnetize this. So
it'll show you the cracks and allows them to repair it and test for more cracks and then do a full
repair on it. So they've done that on this bucket, now they're installing some wear product in here.
So this is AR400 plate, and then on the cheeks we have AR400 as well. On the lip we have QT100,
which is a quench tempered steel, so it stands up better when digging hard rock, it's not as brittle.
In order to get these adapters, so what these are called here, is these are
adapters in which your teeth go on. In order to get these to weld to QT100 or AR400,
you have to heat up both the adapter or the wear product and the bucket itself, and you have to
cool it at a certain rate and a certain temperature to allow that weld to solidify and become very
strong. So there's a lot more that goes into building these buckets than people think, you're
not just slapping stuff on and welding it on. There's temperature curing, there's considerations
for different types of steels, there's NDT testing, and then also what does the customer want in terms
of wear product. Is it an oil sands bucket? Is it a hard rock bucket? Is it a coal bucket? Is it going
to an iron ore mine? So everything that Raptor does here is centered around what the customer
needs for their application. So this is going to a gold mine in British Columbia, a hard rock mine,
hence why we have AR400 and QT100 lip and Cat G.E.T. So again, Cat G.E.T., Caterpillar 6040 shovel.
So we are here in a 793 truck box, this is off a Cat 793 haul truck. This box came from Chile,
it came here in three pieces, so the canopy and then the box was split into two, so three pieces.
So Raptor welded it all back together, now they're preparing it for non-destructive testing like on
the other buckets we've seen. They test for cracks, test for defects, repair those, and then they're
getting ready to put a full liner package in here. So Raptor is going to use their chromium carbide
overlay plate, which is their Raptor plate. They're going to do it on the base and on the bowl, so
with truck boxes you get a lot of sliding wear, you get a full load of material and then the truck
dumps, so you get a lot of sliding wear. That Raptor plate, which is a chromium carbide overlay,
is really good at protecting from sliding wear, which is why the entire floor and the face will
get fitted with it. So when Raptor first started back here in Edmonton, Craig ran the business out
of his garage for almost two years. Their 100,000 square foot facility here at Edmonton, Alberta
was their first facility that opened in 2011. From that point they've grown beyond into Peru, Chile,
Florida, China. So we're here in Raptor's overlay bay, this is where they do stuff like ARM,
abrasion resistant material overlay, and plasma transferred arc. These are welding robots out of
General Motors truck assembly plant. Raptor purchased these and repurposed them for doing
overlays on things like cutting edges, browsers. An example of an overlay, so this is called
ARM, this is abrasion resistant material. So these are ice lugs and these get welded onto
grouser pads. So the abrasion resistant material is very high impact and high sliding wear resistance.
It's basically just a molten flux with tungsten bits that gets applied to the top of the grouser.
There's a couple mines specifically in southern BC that run these because they have a very hard
rock, a lot of silica. So they put an overlay over the grouser and that helps the undercarriage last
longer because browsers might wear out faster than links and sprockets and rollers. So to extend the
life of a grouser, they do a ARM or abrasion resistant material overlay. So another example of
ARM or abrasion resistant material is when they put it on cutting edges. So these are D11 cutting
edges. They're hot so we're not going to touch them, they just came out of the oven but they put
abrasion resistant material on each side. You may ask why on both sides, it's because they flip the
cutting edge. So as soon as this side wears out, you can flip the cutting edge and you can use that
surface. So this just extends the life of cutting edges especially in very abrasive material like
frozen oil sands, extremely hard rock. I was going to pick this up but it's too heavy. This is a
ripper tip off a D11. Raptor does overlays. This is their overlay bay, so PTA or plasma transferred
arc. The first step is to remove paint. So they sandblast it because if you have any paint on there
you can get porosity in the overlay and then it'll just chip off. So the point of the overlay
is to armor up the ripper tooth so that the overlay wears out before the tooth. It just
extends the maintenance interval and how long these teeth last which is not long in the oil
sands especially in winter. So this is the start of the process here is sandblasting the tooth.
It can go into the oven and then it'll go in to get welded by the robot and get overlay on.
These are D11 track pads. So typically in undercarriage the grouser might wear out before
the actual track pad, before the rails and the links. So in this case they've had a robot cut
off the worn out grouser and they welded on new grousers. So they're extending the life of the
undercarriage without having to throw away parts that may still have life left in them.
After this is what's called plasma transferred arc or PTA. As we saw with the ARM which is a
tungsten grit that's dropped in when the overlay is being applied. This is a tungsten powder that's
incorporated into the weld. So you get a lot cleaner smoother finish, really nice weld and
this again just extends the life of the hydraulic mining shovel tooth which this is a Hitachi 8000
or 5500, 5600 tooth. It could go in either. So they're armoring up the edges where it's actually
digging into the active phase to protect the tooth and give it extended life. So plasma transferred
arc this is all automated. So there's a touch screen there and the computer does all this work.
So no one has to stand over it and weld like that. Everything's done with the robots here in this bay.
After we've done overlay whether that's PTA or ARM it comes here and gets a water-based paint
applied and the purpose of that is just to protect it and transport because once the tooth or the
cutting edge hits the dirt it pretty much comes right off. But it gets painted cat yellow here
and then gets shipped to the customer. So that's how the overlay side of the business here works
at Raptor is it gets prepped put in a furnace overlaid with PTA or ARM painted and shipped the
customer and pretty much put to work. But back there we've got hydraulic mining shovel teeth.
We've got whistler teeth in the back there which go on a rope shovel and then we've got D11 corner
bits and D11 cutting edges. So pretty much everything that's been overlaid comes here and
gets painted. Again it doesn't need to be in a seal facility because this is a water-based paint not
does Raptor build buckets rebuild buckets but they also completely rebuild track frames. So this is a
D8 track frame this came out of the oil sands and it's in here at its half-life interval to get a
full rebuild. So that's everything from pins, non-destructive testing for cracks, new rollers,
new idlers. Raptor will do a full once over and rebuild everything including the cannon. This is
what it looks like when it gets here you can see it's pretty beat up it's got lots of oil sand on
it it's pretty dirty. When the track frame comes into the shop they initially do a wash then it
goes to sandblasting and then Raptor is ready to start tearing it down and doing the repairs.
This is a D10 cannon so after Raptor cleans, sandblasts and does initial inspection on the
actual track frame they'll split the cannon from the track frame here. So this cannon goes inside
and there's a spring in here on which the track adjuster pushes on and keeps tension on the tracks
so the front idler sits on there the rear idler is on there and the spring inside here just pushes
out and keeps tension on the on the track so to take it out and inspect and repair it they unscrew
this big nut here that comes out they'll send things off for inspection they'll typically
replace the spring and replace any external seals so right here is the track adjuster.
So this thing here is what you fill with grease to push out and apply pressure and keep tension
on the tracks so this pushes the spring which is inside here and that's basically how the
track stays tight but Raptor disassembles all this reseals inspects anything for cracks repairs those
replaces the spring and then once the rest of the track frame is repaired everything goes back
together. Okay so here's an example of some of the repairs they do on the undercarriage this is a D11
this is called a major bogey so the minor bogeys are in here and that's your rollers and this is
your major bogey this is what the rollers sit in and ride on this is what rides with the ground so
you can see here they've done some NDT testing with metallic particles so you can see they've
found the cracks and there's quite a bit of cracks in this major bogey so in this case the customer
has chosen to replace the entire major bogey but if they were to repair this they would gouge this
out and re-weld this but there is a point in which the metal can no longer take any more stress and
it's so fatigued that no matter how much you repair it it just it won't it won't last so that's what
the customers decided to do is replace this because of that but if it were say one or two cracks they
could gouge this out test it again and then weld and repair it. So we saw the cracks they found
this is after they've gouged it out you can see how deep that crack actually was they had to gouge
pretty much all the way down in here I can fit my hand in there now they're going to build that back
up with weld and then this will be repaired and ready to go back to the customer after they've
installed bogeys painted it things like that this is how they repair cracks on undercarriage.
So from start to finish to rebuild the D11 track frame like this from when it arrives in the shop
to when it's about to leave the shop like this in six weeks Raptor alongside doing things like
new rollers new idlers the cannon seals pins things like that they also do some upgrades to
these if the customer chooses so the bottom plate gets replaced with a one inch thick piece of steel
because you get a lot of torsional forces in there so you have a thicker piece of steel
you have some additional gussets and strengthening brackets inside there and then down here on the
inspection port this is a really common place that D11 and D10 track frames crack is it'll crack
right along this bolt up here so what Raptor does is they actually weld on an additional piece of
metal and fill in these OEM bolt holes and weld them so that there's a stronger piece of steel
right here where it typically cracks so inspection port bottom plate they do a bit on the top plate
as well but it's just a way that they help their customers get a bit longer life out of these track
frames give them the harsh environment in which they work in. Thank you for tuning in to this
episode of the vlog where we showed you how Raptor rebuilds buckets builds their own buckets and
rebuilds things like this D11 track frame I hope you learned something about Raptor and about how
buckets for mining class iron are rebuilt if you want to learn more about Raptor mining you can
check out their website I will leave the link below and we appreciate you watching this vlog
and we'll hope to see you on the next episode. Good Raptor!