HOW TO- Build an aquarium sump - Submerged filter

Fish for Talks
2 followers
Hi everybody, Joe here again and welcome back.
So in today's video I'm going to continue on with part three of a three part series
on sumps.
I plan to show you how to build the three most common sumps based on the method of filtration
used.
Now when it comes to methods of filtration, I break them down into the state the biological
media is actually in, which is either submerged, emerged, or fluidized, meaning the media
is below the water, above the water, or fluidized or constantly moving state.
I plan to show you a basic layout on how to build one, some tips and ideas for them, how
to size them for your aquarium, and the pros and cons to each method.
With that said, last week we talked about the emerged filter, this week we're talking
about the submerged filter.
Now this is the most popular type of sump by far, largely due to its ability to be customized
exactly to your needs.
With so many combinations and ways to build a sump like this, I'm going to cover the
basics while concentrating on the pros and cons.
When it comes to a submerged sump, it's all about the baffles.
Baffles are basically walls inside the sump that contain water and direct it.
The placement of the baffles depends on what you're looking to do, however, we'll cover
a basic layout of mechanical, biological, and equipment.
First we'll need to size the sump.
The size of the sump should be large enough to accommodate equipment, media, and additional
water that will drain when the power goes out.
To figure out how much water will drain into the sump during a power outage, a simple rule
of thumb that I use is to take the volume of the water your aquarium is and divide that
by the height of the tank.
For example, a 24 inch tall 100 gallon tank would drain around 4 gallons of water, usually
it's less, but it's a good start.
Using the 100 gallon tank example, we'd use around 5 liters of appropriate media for it.
We also know that around 4 gallons of extra space in the sump will be needed when the
power goes out.
Since a submerged media sump uses much less media than other methods, we don't need a
huge amount of space, we just need to ensure that the media stays submerged, while there
being enough room for equipment and additional water.
Typically speaking, you can get away with a 20 gallon sump for every 100 gallons of
tank.
This is enough space for the equipment, media, and additional water added during a power
outage.
However, I really can't give you a rule of thumb because you may want to add more equipment
or more types of media, or even more chambers.
As with other sumps, I also recommend running a sump 6 times the volume of the system as
a starting goal.
Meaning that if your main aquarium is 100 gallons, you'll want to run the filter return
pump at 600 gallons per hour.
Baffles are typically siliconed in place and in the general formation that will allow water
to flow under one and over the other.
I tend to use movie or gain cases to use as supports as it dries so I can get a consistency
in height.
This ensures that the water is forced through the media instead of just over it.
You can use glass or acrylic, but I prefer to use glass for this method of sump simply
because glass won't bow as much.
This allows me to create multiple heights of baffles and different water levels in the
tank.
The thickness used depends on the difference in water level.
The first section is important to add a good pre-filter, like some sponge, filter floss,
or filter socks.
Whatever you prefer.
The second chamber in this example will hold my biological media.
Now typically in a submerged sump setting, the biological media of choice is something
like ceramic media, sintered glass, lava rock, pumice stone, something with a lot of surface
area.
The last chamber will hold equipment like the pump and heater, however before it I add
in an extra baffle.
This will act as a bubble wall, meaning that the air bubbles will be removed here before
being returned to the aquarium.
It does this by making sure that the water overflowing into the last chamber has to once
more flow down and under one more baffle before it gets pumped back to the tank.
The water flowing down means that any air bubbles that are being formed cannot flow
under as the bubbles are forced to rise here.
This is an optional addition, however it does come in handy if you don't want to have your
main aquarium full of bubbles.
That's totally optional and typically more common in a salt water tank than a fresh water
tank.
I also like to ensure all baffles are at least half inch from the top of the sump to allow
them to overflow if one gets clogged.
So there's many pros and cons to this type of sump.
Now the pros are that it's highly customizable.
The possibilities are endless.
They also tend to use a much smaller space than other types of sumps and adds more water
volume to the system since the sump is filled.
However some of the cons are that it can get expensive and tend to be the highest maintenance
Meaning that you're going to spend more time taking care of this sump than any other.
I would recommend this sump for people with limited space that want a highly customizable
sump to perform many different duties to help contribute to a very efficient and purposeful
filter.
Anyways guys I hope that you enjoyed this video and this three part series.
I also wanted to thank you for watching and I'll see you guys next week for a new project.
