HOW TO: easy DIY aquarium filter - Hamburg Mattenfilter - sponge filter TUTORIAL

Fish for Talks
2 followers
Hi everybody, Joe here again and welcome back.
So in today's video I want to talk to you guys about and show you how to build a filter
that doesn't get nearly enough attention in the aquarium hobby as it should.
The Internal Mat Filter, also known as the Hamburg Matten Filter, using only a filter
mat and a pump to completely filter and run the aquarium.
Its simplicity, ease of use, as well as functionality makes it an extremely appealing filter.
With that said, it's ugly.
However, I think it still has its uses in certain situations.
This filter operates on a sponge and a sponge only.
The sponge acts as your mechanical as well as your biological filtration.
Now the sponge in question is common filter foam that you would find in a lot of filters.
It's a reticulated foam made of either polyether or polyester.
The foam has a rating scale measured in PPI, which means pores per inch.
The PPI rating indicates the number of cells or pores within a square linear inch of material.
The higher the number, the more pores there will be.
The more pores there are, the finer the material is and the smaller particles it can trap.
When it comes to a mat filter, we need just the right PPI rating to get the most surface
area while avoiding clogging and still allow ample water flow through it.
Personally, I've found that a sponge with a rating of 30 PPI is best used for these
style filters.
I'm going to show you guys two ways on how to set this up.
The first method is with an air pump.
This method would be most useful if you have a fish room and you're running many of these
filters or if you don't have a power head.
The second method is with a power head.
This method simply allows for more flow.
Now remember the sponge filter we made in the previous video where we actually built
an airlift out of PVC and ceramic tile?
Well, we can do the same thing here.
Starting with a cheap ceramic floor tile, silicone a one inch PVC end cap to it.
Wait until it cures and then attach a PVC pipe to it that is a couple inches shorter
than your aquarium.
Drill some quarter inch holes into the bottom of the PVC to allow water flow into it.
Then attach a one inch PVC elbow to the top and drill a quarter inch hole into the top
of it.
Slide some air line into the hole in the cap and attach an air stone.
Run the air stone down to the bottom of the PVC pipe.
The hole in the elbow should be slightly smaller than the air line tubing to allow it to hold
the tubing in place.
Attach a piece of PVC pipe to the elbow and the airlift is done.
Now you can place the sponge in front of the PVC pipe.
You may have to cut the sponge slightly to allow the PVC to fit around it.
Obviously the sponge itself needs to be the height of the aquarium, however the width
of the sponge needs to be about a half inch to three quarters of an inch wider than the
tank itself and this will allow the sponge to fit into the tank snugly.
So that's it.
Turn the pump on and the filter is complete.
Now you can hide your equipment like heaters behind it.
So how do you size a filter like this to your aquarium?
Well I like to go for four liters of sponge per fifty gallons of water.
Now this filter is not really practical on tanks wider than twelve inches.
The largest commonly sized aquarium that is twelve inches wide is actually a fifty five
gallon.
So any wider and the sponge becomes too flimsy as well as the tank starts to increase in
volume and this style filter becomes less effective.
Unless of course you want to add more than one of these to your tank which is doubtful.
These filters are generally best used in breeding tanks, fish rooms and hospital tanks.
The big plus side to this filter is you can hide your heaters and other equipment behind
it as well as act as a divider if needed.
So now that we know a lot more about this filter, let's talk about how it works.
As the air pump pushes air into the PVC, that air rises up the PVC pipe and behind those
bubbles suction is caused.
That suction causes water to be sucked in through the holes we created at the bottom
while lifting water up with the bubbles and exiting out the top of the pipe.
As water is removed from behind the sponge, that water is replaced by tank water on the
other side that is now being forced through the sponge.
To increase the power of such a filter, we can simply replace the air lift with a power
head.
Attach the power head to the wall of the aquarium and possibly use PVC pipe or hose to allow
the output of the power head to flow onto the other side of the sponge.
That's it!
A much more powerful flow is accomplished with a simple power head.
So while this filter has been in the hobby for a very long time, this will serve as an
introduction to those that have never heard of it or seen of it before.
With that said, there are many methods of running one of these and even positioning
it within your aquarium, so feel free to do some more research on this method of filtration.
Anyways, I hope you guys enjoyed the video.
I also wanted to thank you for watching and we'll see you next week for another project.
