How I Handblow a Sculptural Amphora Vase from Scratch

Art Creation
8 followers
Hey everybody, welcome back to the studio. Today we're going to be practicing one of our traditional
shaves called the amphora and I'll be with you every step of the way to explain our process
and how we bring this glass vessel to life. But let's go ahead and head to the studio,
we'll go ahead and get started. So first we're going to start off by giving our vase its base
color. That's going to be an amethyst which is basically like a dark purple. So my brother's
got a chunk of our color bar out of the color box that's preheated to about a thousand degrees
and then he's going to start to heat it up in our reheating furnace to where it's nice and molten
we can spread it across our clear bubble. So first off we're going to get some clear glass
out of our furnace. This furnace stays hot 24-7 and it's on at about 2,000 degrees,
2160 is exactly where we run it. So I'm going to rotate my pipe, get a little bit of clear glass
and this will be the base for our shape. So I'm going to use a wooden tool that we have in this
bucket to shape up my glass into a nice shape so that our bubble will want to expand evenly.
And here in just a moment I'll blow through the pipe, we'll cap it with my thumb and the
air bubble will shoot out of the end. This is what we call putting in the starter bubble. This
is the beginning of any vessel. If we're going to make a cup, a bowl, an amphora, you know anything
that can like hold water or flowers or whatever really, you're going to have to put a bubble in
at the beginning. So this is a very fundamental step. Now we seem to have picked up a little bit
of crud just like some kiln shelf is what it's called. It's kind of like a powder that's a
separator from the ceramic shelf that we preheated this glass on. So I'm going to use my tweezers
and then use my scissors to kind of cut it out because we don't have a chunk of ceramic in our
piece. It's doing pretty well but somebody commented on it and they were like... So now
my brother's going to use our marvering table to shape the glass up into a nice kind of diamond
shape and I'll take this and we'll smear it across my clear bubble to give us a nice layer of even
color. This process of applying color bar to a clear bubble is what we call a color overlay.
Comments on there from other people and they're like what are you talking about?
Thank you sir, looks good. So the basic idea of a color overlay is that we have a cold base which
is my clear bubble and then we have hot color that we put on top. So now I'll heat the color
up just a little bit more and while my clear bubble is nice and cold we can spread that
color all across the bubble so we get a nice even layer.
All right so that looks pretty good and now we have a nice even layer of that amethyst color.
So we're going to go ahead and get our second layer of clear. So I'll take a second gather,
stick my pipe into the furnace, slowly turn and then come out with a new layer of clear on top
of our color. And I'm going to strip. And so I came out with a little bit more glass than I wanted
so we're going to strip a little bit off. This is what we call a strip gather. I kind of just go
vertical and then let the molten glass kind of trail off and I can pick exactly how much glass
I want to leave. So now that we have our new layer of glass we're going to start to inflate the
bubble that we put in previously. So I'm going to use my newspaper tool which cools down the
sections of the glass I don't want to inflate. I'll have my brother Luke blow through the pipe
and the glass will start to inflate a little bit.
For our design today we're going to add some canes to the outside of it and I need our glass
to be a certain size so I'm using this pie divider to figure out exactly how much glass I need.
And we'll go ahead and take our final gather. So you'll notice we use these wooden tools every
time we get a new layer of glass. This basically gives us a second to cool down the outside with
the water that's soaked into this block while the inside starts to heat up. All of that 2000
degree glass can kind of soak into the middle. We want everything to flow together. We want it
all to be homogeneous. We want it all to be one. Can you skip the song Luke? So now we're back to
our newspaper tool. This is one of my favorite tools to use by the way. It really really helps
manipulate the bubble and push it into whatever area you really want. Thank you. So now we're
getting ready to add our canes to the outside of our glass. So we're going to pick up this ribbed
plate that's been preheated and on this plate we have a lot of different canes that are pink and
purple that have a lot of different intricate designs on them. So we're going to take a quick
heat on this and then I'll start to heat my glass up a little bit too and I'll roll across these
canes and pick them up onto the outside of my glass. Okay let's see how this goes. So that went
really well. The timing here really matters. We need to make sure the canes are hot enough for me
to pick up and we also need to make sure that the outside of my base that we rolled it up onto
is hot enough to pick them up without trapping any bubbles in between them.
And now that they're applied to the outside of the glass this begins the process of melting
them in so that everything is again the same heat all fused together correctly.
Baby I just don't know
Yeah it's cool
Someday
All right so now that everything is fused together it's nice and hot I'm going to use my jacks to
start to terminate the end of this so that all the canes run together at the bottom of the piece and
have a nice even pattern. Thank you oh my god of course. All right and with that we have finished
our design everything is put together well we have as much glass as we're going to add
and now we can start to turn it into our amphora shape.
The traditional amphora shape has a kind of tapered body with a hard shoulder
and a kind of angular v-shaped lip so we're going to use the marvering table right here as well as
the newspaper to start to inflate our body and give it that hard shoulder. All right you can blow
don't you care a lot just a little bit of air and we'll get ready for jackpine and you can blow
all right off thank you sir ready
so you can see we've inflated this piece quite a lot it has our preferred tapered shape and the
widest point of the piece is going to be right where we're going to try to put the shoulder in
so now we're going to prepare to add the neck which will be the fluted kind of top of the base
give it some length every time because I've lost all my color up here you know and I want that to
where we kind of go for it a little farther down
this move is called putting in the jack line so the tool I have in my hand is called the jacks
and we're going to put a small incision right off the tip of the pipe and this is where we're going
to start to pull away from the piece to add our neck all right you can come down give me uh just
give me another heat a quick one and come back give me an angle so now we're putting in our second
jack line the first jack line we put in was so that we could establish the shoulder and begin
to put in the neck now this second one will be the place on the piece where we're going to break
it off once we transfer it to a new pipe all right blow for me all right awesome this looks pretty
good so now we're getting ready to transfer this from one pipe to a different one so we're going
to do some final inflation some last minute modifications to the piece we'll establish the
bottom flatten it out a little bit and then we'll get ready to transfer it from this pipe to the
how's it look super sharp so cold work it we'll go ahead and punny you want to help me take this
brother has a second pipe that's just a solid piece of metal basically and we've got a small
bit of glass that's collected on the end this is going to act as a sort of glue bit so that we can
transfer it to this pipe and get rid of our old one we have a small amount of time to make sure
that this is right on center so that the piece stays symmetrical before that little bit that's
really hot right now will cool down so now that we're on we'll add a little bit of water where
exactly I want the piece to break I can pull it back onto the rails give it a tap with my tweezers
and we're off so that went really well the transfer can kind of be a tense moment sometimes
if the piece is going to break that's usually right around when it does but we've made it
through really well so it's looking good so now we're going to start a process called trimming
basically I've heated up the lip of our piece and I'm going to use my tweezers to start to slowly
pull it away and thin it out I'll then go ahead and use my shears here in a second
and we'll start to cut away all the excess glass that's on the lip of the piece
so I'm spiraling aren't I so that trim was a little ugly but it came out all right I'm a
left-handed glass blower so some of these tools are still a little foreign to me in my right hand
the shears are some that always give me a hard time but we have a nice thin lip now and we can
start to put the final touches on the piece this tool my brother is about to use is called the
soffietta basically you can put it on the lip of the piece and then blow and it'll inflate the
piece from the inside do that again we blast the punny and then last thing we'll just we'll just
all right let me take a look that's it let's get it off of here all right so we're basically done
with our piece but we've got one or two last things to do before we're actually done we're
going to have to break the piece off of the pipe and we're going to have to transfer it to one of
our annealing ovens to cool so my brother has some kevlar gloves on and here in just a moment
we're going to break it off into his gloves and we'll transport it to the annealer we apply some
water right around the area we want it to break off at but try really hard not to get any water
on the bottom of our piece and then we can give the pipe a small tap and we're away so this annealing
oven is basically going to cool the glass down over about 12 hours so we'll come back in the
and see our final piece and here's our final product i'm really happy with how this came out
this amphora shape is a new one to me it's a traditional shape but it's a new one that i've
been practicing here and there and i'm really starting to feel a lot more confident with how
these come out i love the color i love the canes it looks fantastic i'm really really happy with
how this came out so if you're interested in purchasing this piece you can find it on my
website either my personal website or my etsy and there's a link in the description box down below
but thanks for hanging out with us today guys i appreciate all you guys so much
and we'll catch you in the next video have a good one
