Altering Thrown Pottery Shapes - Pottery Illusion TRICKS!!

Ceramic Art Studio
35 followers
1 Video View·Aug 29, 2025
Hey everybody, this is Anne. Once you get the hang of throwing basic cylinders and
bowls on the wheel, where do you go from there? In this video, I'll show you three ways to alter
those basic forms to create much more dynamic pieces that are surprisingly easy to achieve.
First, I'll alter a simple round bowl to make it a football shape.
I started by throwing a short squatty bowl and then I let it dry to a soft leather hard.
I flipped it over, centered it, then trimmed and rounded out a nice foot.
If you'd like to see more about trimming a bowl, check out the video link above.
I cut a template out of paper that was a half inch wide and long enough to stretch over the foot and
extend about a half inch along the curve of the bowl. I placed it down along the very center of
the bowl like this. I traced the outer edge of the template with my needle tool, then cut the
section out. I scored the inner area along the opening, then gently pushed the clay inward until
it came together. Note that the rim will bend to an oval shape. I kept an eye on it to make sure
that part of the bowl wouldn't crack. If I see that the clay is a bit too dry, I know I can add
a little water to soften it up. I made sure to work the seam together along the center of the
with my fingers. I then used a rib to smooth it out. I turned the bowl back over and worked in
needle tool to cut v-shapes in the foot for even more interest. This breaks up the foot, accentuates
the narrowness of the form, and actually points your eye towards the alteration points of the bowl.
I love the lines created by the seam when you view it from the side.
Now here's the glazed piece. Jim positioned auto-detailing tape in a pattern across the bowl,
then glazed it with amaco wasabi. Here you can see the inside and the dynamic lines of the bottom of
the bowl. Next, I'll show you how I altered a cylinder shape. With this particular vase, I
started with a pound and a half of clay. I centered it, then pulled up the walls. I cinched in the top
to create the flange. I used a red rib to smooth out the clay inside and out. I softened the edges
of the rim with my fingers. I noticed that the vase was a bit skinnier than I wanted, so I used
a long spatula to push out the body of the cylinder and create this nice rounded shape.
I ribbed it one more time along the outside to get it smooth, then I trimmed off the bottom for a
nice foot. If you want to see more about throwing taller pieces like this, check out the video link
above. I set this aside to dry to a soft leather hard. Now here's a vase I threw previously that's
now a bit drier than I wanted, but I can still work with it. I marked off the top of the rim
with marks directly north and south from each other. Then I marked two marks just northwest
and northeast from the other two marks as shown. Starting just to the left of the south mark,
I drew a curved line down until I got to the northwest mark, then back up about a half inch
from the north mark, back down to the southwest mark, then returned to the right of the south mark.
I marked a dot under the downward points. I created an oval template and lined it up on those
dots and traced it out. I did the same thing on the other side. Since I let this vase dry a little
longer than I should have, I used a wet brush to soften the rim before I made the cuts to avoid
chipping or even breaking along the rim. Now I was able to cut the top of the vase along those lines
nice touch to extend the top part of the rim outward to create a nice line. To echo the higher
extended edge, I did the same thing to the lower back part of the rim. I then cut out the oval
shapes and softened the edges like I did along the rim. That's nice, but the top edge looks
disconnected from the cutouts. To correct this, I thought I could add illusion lines which would
visually connect the two areas. I penciled in lines curving down from the top edge to the top
edge of the oval cutout. I then used a diamond core carving tool at an angle to carve along the
outer edge of the mark and create dimension and give perspective that one section is folded over
the other. Now that's much better. And look, if you hold it straight toward you, you get a dolphin face.
And here it is all glazed. We used automotive detailing tape for the lines around the bottom,
then glazed it with Amaco Sky and fired it to cone 5. Here's another one I made where I used the
smooth surface as a canvas to paint with underglazes. The altered forms provide lots of
possibilities for various decorative surfaces. Finally, I experimented with altering a closed form.
I begin by centering the clay, then I pulled it out wider than I normally would.
I then pulled up the walls until I got it to the height that I wanted.
Then I cinched in the top part to close it off. If you want to see more on how to throw closed forms,
see the video link above. Once the air was trapped in the form, I used a rib to shape the form the
way I wanted. I put it aside until it dried to a soft leather hard. I then drew a line starting
from behind the top point of the piece, curving down along the edge, and meeting back up to the
starting point like so. I then cut out the top part of the form with a needle tool and removed
the section. You remember these? With wet fingers, I softened and cleaned up the cut edges of both
parts of the form. I then fit the top part of the form over the opening so it was offset.
I used a pencil to mark at the bottom where they overlapped. I took the top form off of the opening
and set it aside. I then cut along the pencil mark. I replaced the top part of the form and
marked it where I wanted an opening. I created a rainbow-shaped template, traced along the top of
it, and cut it out. I squeezed the form so the slit would open up. The clay was a bit stiff,
so with a wet finger, I worked the clay until it softened and it opened up for me. Next, I scored
around the outer edges, both on the outside of the form's top and on the inside of the form's
bottom section. Holding the top section by the inside of its new opening, I positioned it just
to the inside of the bottom section like this. I repositioned it until it was straight. I then
used my fingers to begin connecting the two around the outside. I then used my thumb to connect the
top edges together like this. I couldn't reach the bottom edges with my fingers, so I used the long
handle of a brush to connect that section. I then wet the brush and ran it along the outside of the
seam. For interest, I took a little clay and added it along the top lip to echo the folded edges of
the opening. And here's the bone dry version of the one we just made. Now here's an alternate
version where I made two cuts in the form and added just a tiny little handle in the back.
And here's the glazed version of that. The illusion is that it appears there are other
forms growing inside of a bigger form. I love the lines of those pieces. If you like this video,
please like, share, and subscribe to our channel. We'll see you next time in the studio.
