Full Glassblowing Process Demonstration: Twisted Cane Encalmo Basket Vase

Art Creation
8 followers
Hey everybody, welcome back to the studio.
Today we're going to be making a round basket vase for you, and we're going to be using
some very complicated cane and color application techniques.
When we made this vase we had a lot of fun, and I really hope you enjoy the process of
us making it as much as we enjoy putting it together.
Let's go ahead and get to the hot shop, and we'll go ahead and get started.
So to start off, my brother has a little bit of clear glass out of the furnace.
He's going to pick up our red color, and I know it doesn't look red, but that color is
actually about a thousand degrees, and when it gets to that temperature it changes colors.
So I guarantee it's actually red, it's called Christmas red.
So while he's heating that up, I'm going to take a blowpipe and get a little bit more
glass out of our furnace here, and then I'll turn this into what we call a collar.
So when we're making a collar, the point is to really move a lot of the glass off of the
tip of the pipe and create kind of a ring of glass on the outer tip of the pipe.
So you're going to see me push a lot of that glass backwards onto the farther ends of the
This is a really thin bubble, which is exactly what I'm trying to do.
There we go, there's our bubble.
And now I'll put it back into the fire.
That bubble is so thin that it'll all just kind of fade away and recede, and then I blow
through the pipe to make sure that there's no glass off the tip of my pipe where the
hole is.
So now I know that it's a straight shot out, there's no glass in the way, and then I can
go over to my working bench right here, and I can use my tools to push the rest of that
glass off so that I can get a nice ring around the tip.
Now there you can see that that's that Christmas red color.
My brother's got it up to a really good temperature.
And here in just a moment, we're going to actually apply this right onto the steel.
So I'm going to flip that over, put it on, and then we'll just cut off exactly how much
I need.
So now I know in some of our past videos, and all of our past videos, we've applied
red color a little bit differently, where we drop it onto a clear bubble.
This is something new that I've learned, and what we're going to do is I'm going to smoothen
this out, and then I'll actually blow the bubble directly into the color.
So now it may not look like it, but that glass is actually inflating just a little bit, and
now it's hollow on the inside.
So the next step is to get a second layer of glass.
What we're going to do with this color is we're planning on sandwiching it in the middle
of our color design.
So we're going to have some other colors that we apply to the piece in the end, but the
piece is going to have a big red band in the middle of it.
So that's actually the part we're creating right now.
We're using a process called encoma, where essentially we'll make a few different cups,
and then we'll stack them on top of each other and assemble the piece so we get these big
bands of color.
You can blow lightly.
So I want this middle piece to have two holes.
Essentially, it's just kind of like a tube of glass, right?
There's a hole on the top and a hole on the bottom.
So what I'm going to do is I'm using my newspaper tool, my brother's blowing, and we're trying
to push that bubble all the way down to the tip.
So I'm pulling the sides, and the more that he blows, the thinner that it gets on the
tip of the glass.
And I'll take air just one more time.
Should be able to get it on this one.
So now that the tip of our glass has gotten pretty thin, I'm going to start to get ready
to terminate it, which basically means I'm going to cut off the tip so that we have a
hole exposed to me.
This tool that I'm using is called the Jax.
It's basically like a long pair of skinny tweezers.
And I'm using it to thin out a certain section of the glass, and eventually we're going to
knock off this bulb.
So we'll let it cool down, and then here in just a moment, we'll tap it and it'll fall
right off.
Yes sir!
It's the one!
We got a hole!
Alright, so that went really well.
Sometimes if you don't kind of cut off the right amount of glass, you don't really get
that hole on the end.
So that went really well, and now we're going to work on opening this up to the correct
diameter, and then we'll end up breaking it off the pipe, and we'll move on to the next
process.
I'll tell you when we're not recording.
Going to go on light.
Alright.
Sweet.
Okay, I'll put a jack in.
That's pretty far down.
Yeah.
So again, I'm using my Jax to create a small incision where I want to break this off of
the pipe.
Anytime we do this, we usually call it putting in a jack line, which basically means we're
thinning out a certain section of glass so that it can become thin there, cool down to
the correct temperature, and then when we tap it, it breaks right there.
We're basically deciding where we want the glass to break.
You mean Luka?
Yeah, Luka.
Luka's one of those guys.
Racism.
Yep, that's it.
And now we have this to the correct size, and I'm going to double check to make sure
that this is just the right size, and here in just a moment, we're going to knock it
off into the color oven that we picked the color up out of in the first place.
So then it'll be nice and stable in there at about 1,000 degrees, and we can move on
to making the other part of the piece.
They're so different.
And then we can come back to it and reassemble it.
I was thinking about people just a little bit younger than me.
Yeah, well, think about the social situations we were put in when we were younger.
Being born in like, 05 compared to like, 96.
Massive difference.
We're way different now.
Alright, so now that that color is good to go in there, we're going to try to make the
other parts of our piece.
So we're going to do a cane roller.
I have these small bits of glass that I've made a different day.
I actually made these a long time ago, and this is a color called stiff black.
So basically, I'm going to line them up on this hot plate.
We've preheated this plate, and I'm going to let these preheat a little bit, line them
up into a nice little cylinder, and then we'll start to heat them up in our reheating chamber
until they're molten.
We'll try to fuse them together so that they're a nice flat plate.
We want it to all be fused together.
No cracks, no gaps, or anything like that.
And then, I'll actually make another collar similar to like, what I made before, and I'll
roll them up onto my pipe.
This is what we call doing a cane roll-up.
You get these really cool striations and lines.
Doing this is a really advanced technique, but it's a lot of fun when you start rolling
things up.
You can really roll up anything on a plate, and traditionally, a lot of these canes or
marines are rolled up.
So now I'm squeezing these together to make sure there are no gaps, like I said before,
and we actually flip the plate every time we come out because the burner on our reheating
chamber is on the right side, so if we don't consistently flip the plate, that means that
the right side is going to continuously get hotter and hotter, and eventually, if it gets
too hot, it'll end up bonding to the plate, so we have to make sure we get nice, even
heats.
Now we'll dip into the furnace once more, and we'll make our collar.
Just to let you know, a little information about the furnace, this furnace is about 2,000
degrees on the inside, and it holds all of our clear glasses, so we try to keep it as
clear as we can, try not to get any other colors in there if at all possible, and basically
it stays on 24-7.
We never, ever turn it off unless we really have to, so it's been on for about the last
five years.
This one was built for us in 2020, and it stays on all the time, really hot.
It keeps the glass a nice, hot reservoir of glass.
Grabbing those calipers and bringing them to me just for a second.
So now I've measured the canes, the length of the canes with a pie divider, and basically
what this little thing does, you'll see the tool here in just a second, it basically takes
the length of my canes, divides it by pie, and tells me what the circumference of my
collar needs to be to roll it up perfectly.
So I have a small amount of time while my glass is nice and hot, and I can manipulate
the glass to be that size so that I can roll it up to a perfect cylinder.
Glassblowing is a really big team sport, you always have to have good communication with
your assistant, who today is my brother.
So now, we've got everything the right size, the right temperature, and we'll roll it up.
Alright, so that went really well.
It's a little bit bigger of a gap than I want, but that's okay, we can squeeze these together
a little bit more and minimize that gap.
And that happens, you know, these canelips can be quite difficult sometimes.
It's all about the setup, you know, if the setup's right, it's all going to go well.
But if you're off by just a little bit, you know, things can kind of get hairy, so it's
all about the setup.
So I wanted to really talk to somebody and learn from somebody who knew how to do it
right.
Alright, so now that everything is sealed, I've actually gotten rid of the big gap.
I'm going to roll this around and try to minimize all of those little lumps.
You know, each one of these canes has an arc on it, so I want this to be nice and smooth
by the time that I'm done with it.
So we're going to try to heat it up and smooth it down and heat it up and smooth it down.
This process can take a little while, so we have to repeatedly get the glass hot, roll
it around, and try to get rid of all of those ridges.
And the main reason we really want to get rid of the ridges is because I'm planning
on dipping this back in the furnace here in just a little while.
And if I put this back in the furnace while it has all of those ridges, it's going to
catch a bunch of bubbles.
So whenever we go into the furnace, we want our piece to be as smooth as possible.
Sometimes you don't if you want to catch bubbles, right?
But if we're trying to get rid of bubbles, then we don't want there to be any ridges
and we want this to be nice and smooth.
There we go.
And I'll just get rid of this.
I don't need to...
And now we'll just close this off so that it creates a bubble on the inside of my canes.
And here in just a second, I'm actually going to knock this off onto a piece of wood and
we'll save this for later.
Sometimes we use these knock-off pieces to make other pieces.
I actually have a video on my channel where we use a lot of these to make a piece.
I can link it down below.
But you have a lot of recycled pieces when you blow glass, so sometimes we use them to
make other ones.
That is crazy, dude.
Alright, so now we've minimized a lot of those ridges and I think we're ready to gather.
If there's not a Starbucks in the area, don't...
Pretty, pretty.
So this technique is what we call a strip gather.
So anytime we get glass out of the furnace, we refer to it as gathering.
But now I'm going to strip off any excess glass that I don't need and just let it trail
off so I can kind of pick how much I want.
And now I'm over at the workbench.
We're going to use this wooden tool.
We call this a block.
And we're going to shape that glass while it's nice and hot.
Now that everything is kind of back to a basic shape, we'll start to inflate it.
I'll have my brother blow through the pipe while I use my newspaper.
And this tool is about 12 sheets, 10 sheets of newspaper folded up and soaked in water.
It's one of our most basic tools that we use, but it's also one of our favorite.
The plan for these canes is we're actually going to twist them up.
I want to make a really, really tight spiral.
So I'm starting to inflate the piece and lengthen it.
And here in just a moment, I'll put a handle on the tip of it.
We'll chill the handle out by dumping it in the water a few times.
And then I can use it to twist the middle.
I'll cool down the tip, keep the middle really hot,
and then it'll want to twist and twist and twist to get some really, really cool spirals.
You catch her in the middle of the night, and you're like wrapping around her arm.
Blow lightly.
Off.
Make sure to not untwist it.
Can you blow for me? On.
Alright, so that went really well.
You know, sometimes that move can be quite difficult.
It's all about your thickness and your distribution of your canes and everything.
So it's all about the setup, like I said before.
It's all about how you set it up and execute it.
Blow.
Sweet. That was real sweet.
Give me some air. On.
Alright, so the plan with this is we're actually going to turn this into two cups,
similar to the bed cup that we made earlier today.
So what I'm going to do is even out my bubble
and try to make sure the bubble is nice and evenly distributed through the whole thing right now.
And then in just a moment, I'll put a jack line in the middle, right there.
Right in the middle.
And that'll divide it into two pieces.
We'll use the piece that's farther away from me on the tip as the cap of the piece for the end.
And then I'll use the part that's connected to the blowpipe as the collar
to start assembling the pieces back together.
Thank you.
Mystery, bro.
Baby.
So now my brother's going to get a small bit of glass out of the furnace, just like before.
But this time, he's going to turn this into what we call a punty.
This is actually called a sculpture punty.
So he's going to marver this flat, use the table to marver it flat.
And then we're going to stab this on.
And I'm actually going to put a small little handle on this
so that it's not connected directly to the piece.
We're basically putting a small little buffer on this.
I love that sound.
But this is what's referred to as the punty transfer.
So someone will get a pipe with a small bit of glass on the tip,
and we'll use it as a piece of glue to attach onto the piece
while being disconnected from the pipe.
So any time that somebody gets a small bit of glass
and we transfer it to the pipe with a small bit of glass on it,
it's known as called a punty transfer.
It's such a long way to go.
All right, ready?
Yep, good.
And there we go. That went great.
So now we're going to focus on opening up these little holes
on the end, these openings, to be the same size.
The same size as the red cup that I measured
before we knocked it off into the oven.
So we'll end up putting the cap, this one that I have right now,
back into that oven, but we want to make sure
that they're all right around the same size
so that we can take them and assemble them back together easily
without having to manipulate them at all.
You know, like right before bed or something.
I'm scared she won't break a piece.
There with this one.
It's like this clip of the guy,
I think he played Dinesh on a, what's it called,
Silicon Valley.
He's like in a different show where he's like this influencer guy
who only does stuff about Christmas,
and everybody's like, oh, you love Christmas.
He goes, I hate Christmas.
I had one Christmas video blow up.
Yeah, this will be aight.
It's coming out.
The stoves.
Off.
Wax the jacks, corn!
So now that everything's sized up,
we've got all of our pieces where we need to be.
Now to actually start making our piece.
You know, some of these glassblowing processes,
the really complicated ones, like using polymer processes
and things like that, they take quite a long time
to really actually start to make the work.
So right about now, we've been blowing glass
for about an hour making these pieces,
maybe even a little bit more.
All in all, this piece took about two hours to make.
So it's kind of shocking sometimes, you know,
we spend all this time in prep,
and now we're actually going to start making the piece, right?
So up until now, all we've been doing is color application.
And really, we're still doing the color application.
We just have all of our pieces.
So we just need to assemble,
and then we'll actually be able to turn this into the base
that it's going to be.
Got a price check?
Yeah.
Still a little big.
Flip.
I don't know about getting this off.
Yeah, it's hot.
Get me some water.
Yeah, but I don't want to get it on the thing.
That's good.
Do it.
Alright, so we got one cup on,
and now we're going to open this up.
It seems as though the hole got actually sealed up,
so I'm going to open it back up with my tweezers.
But now the plan is to open up that red cup
to the right diameter,
and then we'll be able to add the third cup onto it.
Yeah.
Oh, wow.
Taking it to the street.
It's a little hotter.
We'll go for a price check when we come out.
Okay, so now after this lengthy process,
we're going to add the third cup.
So I know on this one, that was a little bit big.
You can see on the bottom,
where I guess the cup was a little bit big,
and my base was a little bit small,
which is okay.
We handled it alright.
But, yep, in the future,
we should have price checked again
and sized it up a little bit more.
But it's okay.
Won't mess with our pattern all that much.
It'll be alright.
Your butt's sweating, Mark.
For a second.
My butt is sweaty.
Okay.
Alright, so now that our pieces are back assembled
and everything's ready to go,
we're going to do something like we did earlier
whenever we were trying to smooth out all those canes.
So I have two seams, I have two lines
in the middle of the piece
from where we added the different cups.
So right now, I'm going to try to minimize those lines
so that I don't catch any bubbles
whenever we gather on top of this.
Because the next part of the process
is to go and get another layer of clear glass
out of the furnace.
Sweet.
We'll let it cool down.
I'll come out and strip.
Glass is seedy.
Alright, so that was the last gather that we'll take.
Now we have all the materials that we need.
And from here on out,
it's a good old-fashioned glass block.
So you guys probably noticed,
especially if you've seen some of our other videos,
that I really like using my newspaper tool.
You know, the idea behind expanding this kind of bubble
is that it always wants to take the path of least resistance.
So the pad really gives me a good kind of leverage
over controlling where the bubble goes as my bubble goes.
I'll take some.
Off.
So now we're going to put in one of those jack lines
that I talked about before.
So basically, I'm establishing
where the top of the piece is going to be.
The bottom is obviously going to be where the tip is,
but I'm putting in this little incision
so that when we break it off the piece in the end,
this will be exactly where it breaks.
On.
Oop.
Yeah, on.
Off.
His name is Tony.
Sopranos is like easy, but...
A little hard.
We'll do that again.
Quick games, Luke.
Let me tell you something.
Off, off, off.
Ah, I just squished the crap out of it.
Sopranos?
Yeah.
I heard this is the best part.
I got mom and dad watching it now.
I know, they're on it.
They're watching two episodes a night.
Yeah, yeah.
It's awesome.
I mean, it's a good show.
Like I said, it's a good show.
Blow lightly.
Apparently, my folks.
Off.
We all got time for that.
You gotta try that.
About the bunny.
Sorry?
What'd you say about the bunny?
Oh, it's such a good shot.
There it is.
So yeah, a bottom.
We'll put the bottom on now.
So now we have the final shape of the piece.
Almost.
And it's time for the punty transfer.
So my brother's got a small bit of glass on this thicker pipe.
We're gonna try to stab it on.
Whenever you're doing these transfers, you always want to try to put it directly in the middle as much as you can, right?
Glassblowing's all about symmetry.
So I'm trying to make it as symmetrical as possible.
Right in the middle, if I can.
And now, I'm gonna heat up my connection point so that it really wants to break there once I apply some water.
And then here in a second, you'll see me grab my tweezers, get some water out of the bucket behind me,
and I'll apply it right to that little jack line that we put in.
And hopefully, if I did my job right, it'll break right off.
Alright, ready? Lift up.
Sure looks good on him.
We'll paddle the lip very quickly.
And there we go. That went pretty well.
You know, the punny transfer, especially these bigger ones on these kind of mid- to large-sized pieces,
can always be a little bit anxious, you know?
That's because, basically, if the piece is gonna break at a certain point,
usually that's when it'll break if we're not set up right.
So, glad that went really well.
And now, we're gonna slowly open this up a little bit.
And my brother is actually gonna bring over a lip wrap with a small bit of red color that we had left over from when we made the cup.
So, here in just a moment, he's gonna pick that up, get it hot, and bring it over,
and we'll give this thing a little rim for it.
Here we go.
And there we go. That went pretty well.
Lip wraps are something that I'm still kind of learning how to do,
so I want to use them more and more in my work.
But they have to be applied just right. It's all about the setup and the application.
So now, we're gonna try to inflate the piece just a little bit more
using my Soffietta tool to inflate it from the inside.
Now, we'll go through that process just a few more times, try to make it nice and round,
and we'll basically be done with our piece.
It won't fit, will it?
Yeah.
No.
I think that's gonna be it.
So, we're basically done with our piece, but we're not exactly out of the woods yet.
So, here in just a moment, we're gonna have to disconnect it from the punty rod
and transport it to our annular to cool it.
Now, I'm gonna apply some water to the connection point,
which is slightly difficult.
You want to apply water as close to the bottom of the piece as possible,
but you don't want to get any water on the actual bottom of the piece.
You've got to get very close, but not too close.
So, I'll apply a bunch of water, and here in a moment,
I'll knock this off into my brother's Kevlar gloves,
and we'll transport it to our annular to cool it.
All right. Ready?
Got it. We're gonna map gas.
All right. That's it.
Look at that. Cool.
Awesome. That was great.
All right. So, that was great.
I really had a good time putting this piece together.
I'm really trying to use these twisted lines a lot more in my work,
so I've been practicing that a lot, and this came out great.
I'm really, really happy with the result.
And, guys, as usual, if you're interested in purchasing this piece,
you can find a link to it down in the description box below,
either on my personal website or my Etsy page.
Either way, it'll be posted on either site.
And thank you guys so much for hanging out with us today.
We had a really good time throwing this together.
I really hope you guys enjoyed it as much as we did.
So, have a good one. Be safe out there.
