🛠 Your Electrical Learning Partner – Arun Gupta 📘 Books | 🎓 Courses | 📲 Support | 📈 Career Growth
══════⊹⊱≼≽⊰⊹═════════⊹⊱≼≽⊰⊹══════
How to Use a Multimeter – Complete Guide for Electricians 🔧 Learn how to use a multimeter step by step! In this video, you will understand how to measure voltage, current, resistance, continuity, diode test, and more — both in theory and practical.
Whether you're an electrician, technician, or student, mastering the multimeter is essential for troubleshooting and safety in electrical work.
how to use multimeter multimeter tutorial multimeter for beginners how to check voltage with multimeter how to use digital multimeter electrician training multimeter kaise use kare electrical multimeter guide voltage check with multimeter continuity test multimeter current check multimeter house wiring tools learn multimeter step by step multimeter full explanation electrician tools training electrical measurement basic electrical tutorial digital multimeter use in hindi multimeter testing electrical troubleshooting multimeter
Friends, through today's video I will
teach you how to use multimeter 100%.
You must know
how to measure voltage through a multimeter.
How to check resistance. But
you will not know how to
check the diode. If I tell you that
you have to check the capacitor
through a multimeter, then perhaps you will
not be able to do it. Apart from this,
how will the contractor check what has been done?
How to check the relay? I am going to teach you how to measure current
using a multimeter through this
video.
So friends let's start the video.
Look, the first thing here is
my multimeter, in this multimeter you
get a display in which you will
see the complete value here, whatever
measurement you do. Second thing, here you will
find a rotary dial through which you have to
select what you actually want to
measure. Do you
want to check the capacitor here? Do you
want to measure DC voltage here?
Do you want to measure AC voltage here
? Whatever selection it will be,
you will have to do that selection through this rotary dial.
You will understand how to do it later.
Apart from this, pay port is given here.
Along with the port, you have to connect this
probe, the probe of the multimeter.
Now, it is
very important to always connect this probe in the correct manner. Otherwise,
your multimeter will blast. How will it
happen, I will explain it to you further.
Understand it at the present time. This
probe here,
you will do the measurement here only by using this probe. So, to
make the measurement, your probe here, this
probe should be connected to your multimeter.
Meaning that through this the data will be given to
our multimeter and the multimeter will
show the value here. So, let us
first understand how to connect this.
So, here you will see that
in this multimeter, three ports are
given here. Of which one is common. So the
common port will always
have the black one. You don’t have to change this
ever. You can measure anything here. The
black probe will always
connect to the comb here. After this comes the
red port here. Now there
are two red probes here. So simply you understand that
if you go to measure the current then
only you have to use the port A here.
It should not be used at any other time.
Here you simply have to use the port having voltage resistance and
milli ampere.
If you are
measuring voltage, if you are measuring resistance, then
you simply have to use this port. The
rest is
not to be used. So
what do you simply have to do on this port? This probe, the
connector of this probe will have to be
brought and connected here. So
we have connected the multimeter here.
Now we have to do measurement here. So
first of all we measure the DC voltage here.
So
here I have different types of batteries to measure DC voltage.
We will use these
for measurements. So if you go to measure DC voltage,
you will
have to select DC voltage here in the multimeter. Now you will
see here that the symbol of DC voltage is made.
So you will have to make a selection at this place.
But for sectioning, you will see that
here the range from 200 millivolts to 600 volts is
given. Meaning, the voltage that you have, the
voltage here,
what is the range of this voltage? How much
is it worth? You have to make the selection here according to that.
Suppose
you don't know what the final voltage of this battery is.
So first of all you have to
select the maximum voltage. I
mean
what is the highest voltage here
? It is 600. So here you have to
select 600 first. If you
don't know its voltage then what will you
do next? You have a probe here, this probe has to be
connected with the battery. So here
I have a battery. Let us measure this.
So you will see that there are two ports in this. So
you can install it anywhere in both the ports.
However, it has to be applied straight. But
you can put it anywhere now. So at present,
this is how I apply it. So
look here the voltage is showing 6 volts. The
voltage shown here is 6 volts and
a minus symbol has also appeared here.
If the minus symbol appears then it means
that the probe you connected here has been
connected upside down. Meaning that
you should connect the red probe at the place where the negative is.
Now you will see that
I had connected the red probe on this, so
minus is written here. That's why the
minus symbol is appearing here. I
connected the probe upside down. If I
interchange it like this. Meaning that if
I connect the positive side of the battery here, then
connect the red probe on the positive side and the black probe on the negative side, then the voltage here will
directly show the voltage here.
Negative symbol will not appear. If
I make a change here then the negative
symbol will appear and if I apply it directly then no
negative symbol will appear. So if you
see the negative symbol here
then you should simply understand that the probe you have
inserted is upside down and it will have to be changed.
Now notice one thing here that I am
measuring the voltage here. So the
voltage that I am going to be is 5 volts. Now
here I get an idea of
what the voltage of this battery is going to be. 5 volts
so I will select the range here
because it will not show the proper value
at 600. If I have to see its proper value,
how much voltage is it giving. So for this
I will have to reduce the range here. So the
range here is 2 volts and then
five. So there is a two next to five. If I
select two, then it will not be
able to do major. It will say it is overloaded. Meaning that
its capacity has exceeded that capacity.
Meaning, you will see here that
if I apply this then it will not show the value.
OL will do the show. Why so? Because the
voltage here is 5 volts
and if you have selected 2 volts in it, then if the
value is more than 2 volts, then it is
not able to measure it. Then what do you have to do
? Here the range will
have to be increased. Have to select at 20. By
selecting 20 we will get the voltage here. If you
look at the voltage, here it is 6.24.
When I selected six here it was
showing 5 volts. But now the
actual voltage is showing that the
voltage of this battery is 6.21. But if you
look at this battery, it is
written 9 volts. There is a 9 volt
battery but the voltage is low here.
Why so? Because the battery has become
old or discharged.
So if
you see a voltage lower than the voltage of your battery then
simply understand that the voltage is
down here. The battery is discharged here.
So I'll
have to use a different battery here to show you.
So right now I have
one more battery here. Let us measure this battery.
So if I measure the voltage here in this battery, you will
see that it is coming out to be 9.25. And its voltage is also the
same. It is of 9 volts. So if the
voltage is more than 9 volts of the battery then the battery is
charged. If it reduces to less than 9 volts
then what is it? The whole thing is dead.
And if it is at 9 volts, it means it is
discharged. 9.1 9.2 is coming.
Understand the meaning, there is discharge. 9.5 means it
is still in charge. Ok? Here the voltage is
showing our proper. Looking at
this, our battery has been discharged. The
voltage has gone down too much.
Ok? So our battery got damaged.
Friends, before moving ahead I would like to tell you
that if you are an electrician or an
electrical engineer, then you should have this
book. The
name of this book is
Zero to Hero Housewarming Book. There are
more than 1990 pages inside this book.
Through all these pages you were told
how to do electrical work.
Look, when we work in the industry, there are
a lot of things that need to be
done in house wiring. It is
also used in industry.
We don’t know all those things. At present
we are studying about multimeter here.
So
you will also get the information about multimeter in this book.
As you can see, here it is
explained about the multimeter and
how to use it.
How to check DC voltage, AC voltage and
resistance. Similarly, the
claim meter is also
explained here. Apart from this, if you
move ahead in the book you will see
how to identify the cooler motor.
How will we check the cooler motor
, how to make the connection,
how to install the capacitor, every single thing,
you will get to see in this book.
Apart from this, there are many other
topics which you can understand by reading this book.
Ok?
If you want to buy this book, then
I am going to provide you the PDF of this book.
You will get the PDF for only ₹100 and
if you go to buy the PDF, you will
get two options there. You can check out the book here whether you want it in Hindi or
English.
You can buy whichever book you want.
Apart from this, if you do industrial work or
work in the industry, then
I have another book for you which you
already know. Electrician A to
Z wiring book the work done in the industry,
contractor timer relay dual
starter start delta starter, this
type of concept is there, be it sensor,
overload relay, float switch,
similarly how does your push button
work,
how to connect CCTV camera, so here if
you want to learn about this type of concept then
you can buy this book, you can buy the PDF of this book for
only ₹98
and you will get the PDF of Zero to Hero house
wiring book for ₹100
if you want that this
book which I have in my hand. If you get this book,
you can buy it for only ₹600.
Apart from this, if you
want to buy a house wiring book
in this type of format then you will get this book for
₹1000. You can order this.
So if you want to buy the PDF
then
I have simply given the link in the description of this video.
You can buy directly from there. I have also given the link to
buy the printed copy of this book
in the description of the video. If you order a book, then
after ordering I will
directly courier the book.
Our courier goes in this manner. After couriering the book,
I will send you the tracking details on your
WhatsApp number. From there
you can track where your book has
reached. Ok? If you face
any problem after making payment and you are
not able to get the PDF, you
can also contact me on my WhatsApp number.
Well, as soon as you make the payment,
you will get the option to download the PDF after making the payment. Apart from this,
you can also download the PDF by going inside my app, Electrical Technician App.
If you have bought the book.
After clicking buy your PDF could not be downloaded. There is
no need to panic. This
app is Electrical Technician App,
I will also give you the link of this app
in the description of the video. Simply login to this app.
After logging in, there
is an e-book tab here. Please click here.
After clicking here, you will
get the option to download your PDF. As you can see,
here the option of pay view and view
demo is coming. So I have marked it as bye and
it has opened here. Once you
make the payment it will be unlocked here.
After this, if you come down then there is
book 02 to Hero House Wiring here.
I have not bought this book yet, so
look here it is showing Buy Now. Ok
? So if you want, you can directly go to the app and
buy it or you can
download it by buying it from the link I have provided
and in future if you
delete the PDF then you can login to this app and
download it directly from here.
Now let us come to our topic.
Now let us talk about AC voltage.
If you have to check AC voltage here
then how will you do it? So see, there
is the same method to check this also. You just have to
select AC voltage here in the multimeter. Right now we were measuring DC, so we
selected DC voltage. Now if we want to
measure AC voltage, so we will select AC.
I rotated it here and
I don't know the voltage. Actually, our
homes get 230 volt power. But
if you don't know then select the highest
and if you know the voltage
then select the range accordingly.
Whatever I told you here, the same thing will apply here as well.
Right now there is 200 volts here and
its voltage will be 230. So if it is 200 plus then
it will show OL. So I have selected 600 to
show the voltage. Now if I
place the probe of the multimeter here,
you will see the voltage shown here.
How much voltage is there? 237 volts is coming here.
Even if I change the probe there will be no
problem. Here in single fuzz it
shows us the voltage. Negative
symbol will not appear. Ok? So if I
place the probe of the multimeter here then you will see that
238 volts are coming. Ok? So
even if you change it, it will not make any difference. So
we can measure AC voltage in this manner.
Now you have learned to measure AC voltage.
So after this what do you want to major in here
? Resistance. Now here you have to
learn to measure resistance. There
is some resistance of this type. If you
want to know how many ohms the
resistance is. Or else you can ask some
contractor whether the coil of that contractor has gone
bad or not. If you
want to check it then you will
have to select the resistance here. So
we will turn it around for resistance.
Here in the resistance. Now the
resistance too is given in a wide range.
Like here you have to
measure the resistance of 200 ohms. Here it is 200
k ohm, here it is 2 million, 20 million, in this way the
range is given here. In which range do
you want to measure the resistance? If you do
not know what its resistance will be, then
select the maximum here.
And after selecting maximum, there is no need to
change the probe of the multimeter. It will
remain the same. You have to connect black on the common port and the red one on the port which has
voltage or resistance.
Ok? So
if I have to measure its resistance at this time,
then simply what will I do?
I will touch both of these once. Here the
value should be zero. Correct? Now I
simply connect this probe with this resistor here.
Look here, it has started showing the resistance.
But it is showing zero. why is it showing zero
? Because here I have
selected a very wide range. And my
resistance here has a low value.
So let's reduce this a little bit. I
selected 200 here.
After selecting 200 let's see how much it is showing.
Right now it is showing 0.4 here.
Meaning that something value of 400 ohms is coming. will
come. So if I
select 200 at 2K here, this will happen.
Here our resistance is coming at 0.459. That
means
you can assume 459460 ohm resistance. What does K mean
? If you divide 1000 by K
then we will get a resistance of 460 ohms. There
is more here. Let's
check this. So when I applied it here,
its resistance is showing OL here
because its resistance is high.
Ok? Its resistance is high
so it is showing OL. The range will have to be increased. I will
check it here. How much is coming? The
resistance of 17.8 ko is shown here.
Well, pay attention to one thing. If
you want to check the resistance in a circuit.
Like you have a
contractor. If you want to check this contractor, then the
power supply in the contractor will
also be connected here. So
if your power supply is connected then you have to take
care that the power supply
should not be on here. If you measure resistance and
check continuity, then your
power supply should not be on here.
After switching off the power supply, simply
bring the probe of the multimeter to the place where you want to
measure the resistance.
The coil present inside this contactor is
brought and connected to A1 and A2 here.
So what you will do is simply
place the probe here at this place.
After application, measure the resistance.
Here it is showing that the resistance is 0.5 ohm.
So I have selected this range pretty much.
To measure some proper resistance I
selected 2000. The resistance here is
showing 0.554 ko. Meaning it has a resistance of 554 ohms.
If the
resistance here shows zero or OL then
it means that this
contractor has gone bad. But right now it is
showing some resistance here.
This means that our contractor
's coil is in OK condition. Ok
? So we checked the contractor's coil.
Well, I
also have a relay here. Let's check this relay.
So the coil of the relay is on
this side in front. This is not front on the front side. The
front will be on this side.
This happened on the upper side and this happened on the front. So on the
front two terminals,
we will get the resistance of the coil of this relay.
A relay coil is installed here.
We will see its resistance here.
So I
connect this multimeter probe here
and check it. OL is
showing here. Meaning there is even more value than this. I will
increase this. If you
increase the oil here then you will have to increase it further.
It is still showing oil. So I have
not connected it properly. It seems like.
Ok? I placed it here. Now
look at this screw which is loose. It is
not working because of this. Now see
what is showing here? 0.019 Too
wide a range selected. Let's reduce it.
Showing a resistance of 19 kilo ohms.
And I do less. OL is shown here.
Meaning, we will have to measure the resistance here.
Its resistance is coming at 199000. 19000 ohm. Ok
? So this showed resistance here. In
this way you can measure the resistance.
Now to see whether its resistance is proper or
not, the value is also written in it.
You will see that here it is written
coil and in front of the coil 19 kilo ohm is written. This
means that this coil has a resistance of 19000 ohms.
So it is written here, so
match through this. Is the
resistance here equal? So,
how much resistance was there in what we measured
? 19 kilo ohms. Meaning that is correct.
This coil of ours is correct.
It will work properly. So you have also understood how you will
check the resistance here.
Now that you have learnt how to check resistance,
you should also know how to check continuity
and diode. So
if you want to understand continuity,
how to check continuity, then simply
understand that by using continuity we
can check
whether current will be able to flow through a particular wire? Is this
wire cut in the middle? If you
want to check this then you will
check the continuity here. For this you will have to
simply pay on continuity.
After putting it on continuity, if you touch both of them
together then a beep sound
should come. A beep sound is coming. You will see that it is
also showing zero. Correct? Now I will connect this
wire to this point and to this point. There
is a beep sound here. Resistance is also showing zero.
Meaning there is continuity. If
I supply power at this point then it will come here.
If the value here
shows resistance or OL then it means
that our wire is cut somewhere in the middle.
OL means cut in the middle
and if it is showing resistance here.
Meaning, there is something wrong in between. The wire is getting
a little rusted or the
wire is cut. There is a slight touch
due to which it is showing resistance. You can believe this. At the
current time the proper
value here is coming out to be zero. Meaning that
our wire is okay. We can use this. So
this is made of wire. Ok? We do
n't have to check the wires right now. What do we have to check
? The contractor has to check. If
you work in the industry, then this
type of contractor has to be checked.
So when we
start this contractor, what does its ano contact do
? Gives the power supply.
So you will have to check whether Eno Contact is working properly or
not.
So what will you do to check this
? Place both the probes of the multimeter
here in this manner
and press it.
What is happening here when I press? Showing OL.
Unable to connect properly.
So I will put it on this side.
And I put the other one on this side.
Ok? Let me place it here and press it.
Now see, the beep sound has started coming.
What happens if the multimeter's probe is not connected properly?
Resistance starts to show. This proper is
coming here now. Ok? So now
if I am getting continuity on pressing this
and not on releasing it then it
means this is a no contact and this is correct.
I will check it by pressing it two-three times in this manner
because here I have to
verify whether it is working properly or
not. Ok? that'll be.
N Contact is proper. If you
have a push button. Like here
I have a push button. I have to check
whether my push button is correct or not.
So if I have to check this push button
then first of all, if there is a power supply in it,
then I will turn off that power supply.
Meaning, I will switch off the MCB.
After switching off the MCB you can check this contact here.
Is this an ANO contact or an
NC contact? First let's check the NO.
So to check NO,
I place the probe of the multimeter here like this.
And then I press it. On pressing
here continuity is coming. The
meaning is correct. Closed on release. It
comes here when pressed and
stops when released. Meaning that the anno contact is correct. Let's
check NC. What does NC do? Will
always keep the power supply flowing. That is a
closed circuit. Let's check the NC contact.
Beep sound is coming
in NC contact. But when I press it.
Here I press it with
this finger. So when you press it will go away
and when you release it will start. Now see, I am
also pressing here.
what happened when I pressed it? It got opened. On release it will
start giving continuity here.
So the NC contact always
gives continuity if you use it,
but when you operate it then there will be no
sound while operating it. Once you release it,
sound will start coming here. Ok
? So now you have understood how to check NC contact. At
present,
we have also learned to check the resistance here. I
also learnt to maintain continuity. Now here at
this point you will see that the symbol of diode is formed. Let us
also understand diode. So
you will see that this type of
diode is installed in many places. What is its function
? Converting AC power supply to DC
or making the power supply
flow in one direction only. So if
you want to check this then there is
no need to make any changes in the probe again. When to change
? When you have to measure current. Now if
we have to check the diode, then to check it we need to
understand one thing that this
part of the diode is our cathode
and this is the anode. Anode means
positive and cathode means negative. So
you have to place the red one of the multimeter on the positive point and the
red and black one on the negative point. If you
place it in this manner then you will
see some readings here. Here you will
see some readings are coming. What is the reading
coming in? So the reading ranges between 0.4 to 0.7
according to different diodes. So currently,
in our conditions, the reading here is 0.4 volts. This
reading which is coming here
means that the power
supply will flow from this side to this side. Now when we
turn this around, we
should not get any reading here. You have to
check two things here. First of all you will
check it directly. You will put the positive on the anode and the negative on the cathode
and check here
whether the diode you have here is showing any value here. The
value is showing means correct. Now turn it over.
After turning it over,
apply it like this. Check it here. It's
showing OL here right now. One
should not get into this condition. If you connect the black probe to the anode
you
should not get any value. OL
should tell. If the value is shown here. If the
value is shown here it means that it is
short and if OL is shown here and
on this side when we are measuring directly
and in this also OL is shown here then
what does it mean? It has been opened. Sir,
your diode is open. Ok
? It is broken somewhere in the middle. It has become open in the middle
due to which your
contours are not being formed. So our
diode is correct. Showing value from this side as well. The
value is showing from this side
and the value should not be shown from this side.
So it is not showing here. Meaning the
diode is correct. Ok? So
you have also understood how to check the diode. Now here
comes the NCB. NCB is a very important
function given in your multimeter.
Many multimeters do not have this function.
But if it is there then let me
explain it to you. Look, by
using NCB, you can find out
whether current is flowing in your cable? Like
if I take it near it then
look here, beep beep sound is being heard. If I take
it away then the beep sound will
reduce here and go away. If I take it closer,
it will start coming here.
Ok? So by using this function
you can find out
whether any power supply is flowing through this wire, this cable? Like, when
you repair the lights of the chandelier during Diwali,
what needs to be done there?
We have to check each LED light.
And what happens sometimes? If one LED is
damaged, power cannot flow further. The
entire LED goes off. So
if you want to find out which LED is
bad then use this function
and keep sensing there in this manner.
As long as the beep sound is heard, the
power supply is flowing. The beep sound
stopped. Meaning the power supply is not flowing.
You can check it at that place itself.
You will get to know. Ok? So this
is our NCB function. Now after this,
friends, here comes the time to
measure the current. What do we have to do here before the current
? Capacitor. So there is
no option given in it to check the capacitor.
I have another
multimeter here. You will see in this multimeter that
there is an option to check the capacitor.
So let's check the capacitor through this. There
is no option in this.
You do not get the option to check the capacitor in every multimeter.
So I move it to the side
and bring it here
and simply select it on the capacitor.
Then I'll
connect this probe to the same one here. The black one on
black and the red one will be connected to your voltage
and resistance port.
Now look here, the
symbol of the capacitor is there but
along with it there are other symbols also.
Like diode, resistance, continuity. At
this time we have to select the capacitor.
So we have selected this.
Apart from this, if you look here,
Om is visible here. Meaning that it
will measure the resistance now. If you want to measure the capacitor then you will have to
press the function button. The
voltage has come here. The
value of the fard comes here. Meaning you
can check the capacitor. The value of farad capacitor is
in farads. So the
fare has arrived here. So the capacitor I have is
this one. Let us see its value first. There
is a capacitor of 36 micro farad. We will check this. So
what will you simply do to check this? The two wires here will be
connected to the probes of the multimeter. And
there should be no power at the time of checking it.
Plus you don't have to touch it with your heart. If you
touch it with your heart the
value will change. Ok?
If I connect here in this manner, will you
see how much value is coming here?
36.12 is coming. It has arrived but
you do not have to check it this way. You can grab one. You ca
n't catch the other one. The
best thing would be that you simply
apply it like this and tighten it. This one is
installed and the other one is placed here
like this. Ok? Now see what the value is
showing? There was a capacitor of 36 micro FET.
Here it is 35.8 micro fat.
Due to my heart being applied the
value here has changed. My heart also has
some capacitance. He will check it. The
value of this capacitor at present is
35.9. Meaning its value is written as
36 micro Farad but it has decreased a bit.
But this will work. 35.9 means it will
become 36. So this is our capacitor, okay. You
can check this. So
you also understood how to check the capacitor. Now let us come to the
current. So to measure the current,
we will do the measurement through this only. So
if you want to measure the current, then the comb
port will be on this. Now the red
port will change for you.
How will the change happen? So you have to see whether the
current is in amperes or
milli. If your current is
in amperes, that means you should assume that it is 300 milliamperes,
here the current written in
milliamperes is
more than 200 milliamperes, then in this condition you have to
use this port here. If the
current is more than 200 milliamperes then you will
use this port. If the
current is less than 200 milliamperes then you will use this port.
So let me
connect this one here right now. We
will measure the current in milli amperes. So to
measure the current, understand one more thing here. There is
no AC current measure in this.
Your multimeter will always measure DC current.
You will see that where there is the symbol of current, the
symbol of DC is also there. So
here I have selected 200 milli ampere
and it is DC. So I have
selected 200 milli ampere. So the
probe will have to be placed at this place here.
And if I want to measure the current, if I
want to measure the current of 10 amperes, then
I will have to connect this probe here.
Now if I want to check the milli ampere current, then
I will need a setup here.
Meaning that a current flow will have to be maintained.
So here I have a LED, to
turn it on I connect these two wires
together here. If I connect these two
wires then my LED will turn on
and I will take it and
connect it to the battery. I have a
battery here. Connected it with this.
Now see, the LED has started glowing here. The
LED is glowing here. Now if you want to
measure the current then your
circuit will have to be opened.
We can measure the current only after opening the circuit.
So to measure the current I will open it here.
LED turns off after opening.
Now if current has to be measured then current will have to be made to flow.
Meaning the LED has to be turned on.
For that,
both the probes of the multimeter will have to be
placed here in this manner. You will
see here that the light is glowing at the current time.
Meaning, the current is
going to this LED through the probe of this multimeter
and the current being taken at the current time is 49.7 milli
amperes. If I
select ampere here then it will not measure.
Why wouldn't he do it? Because I
ampere,
this port is useful when selecting the ampere here
and by using it in this place,
we can measure current up to 10 amperes.
So right now he won't be able to do the major.
So in this condition it will have to be taken out and
placed here and then if I connect them in this
manner then it will show current here.
What is the current showing now?
Showing 0.04. Unable to show the proper.
So if you want the proper value then you will
have to do the milli ampere section because the
current is very low and I will have to apply it here.
What will happen if it is applied at this place
? Here the multimeter will show my current.
50.1
milliampere current is flowing here.
So in this way we
can measure the current here also. Now friends,
see one more thing here, a hold button has been
given here. What is the function of this button? Let us
understand this. See, the hold button
's job is to stop any value.
Suppose you are doing some measurement. That
measurement is changing a lot.
Your value is changing again and again. If you
want to stop it, on this display, if
you want to stop it then you will have to press the hold button for that.
I will explain this to you in a good way.
For that I will have to
measure the resistance here. So
I take out this probe from here and
place it at this place. Here I
want to measure the resistance. And
I have kept the resistance selected here.
Now look, I have
a variable raster here. Meaning that it
is a variant. I'm going to turn it around like this. So the
resistance changes. So right now
I have to measure resistance. So
what do I do here? I will connect this to this black one
and I will
connect this to the red one. Look here,
how much resistance did you face? 10.5 ko. Now if
I turn this around. If I turn it like this then the
value here will
change. This is not changing. I'm
cooking it wrong.
What will happen if I place it here and then change it? The
value here will change.
This change is happening here. Ok? So if the value
changes repeatedly like this then
in this condition we will not be able to read it properly.
So if you want to stop this value
as I keep rotating it
and hold it then press the button here.
Look, it stopped here. Now no matter how
much you turn it, it will not change. If I
press it again then it will start showing whatever value comes here.
So if you want to
stop any value here, if you
want to stop the value that is coming on your screen, then
simply press this hold button.
Now this will change. The value which was yours at the
time you pressed the hold button will stop here.
Ok? So by using the hold button you
can stop the value
on your screen. After that, you note down and
then press this button again to reset.
After that you can do major. Okay
friends? Before ending the class I
would like to tell you. If you
want to buy our book whether it is Electrician A
to Z Wiring Book or House
Wiring Book. If you want to buy these books then
I have given its link
in the description of the video. You
can say bye from there. After buying it, you
can download it directly from there.
Apart from this, if in future
our PDF gets deleted from your mobile, then you can
login into our Electrical Technician app and
download this PDF again from there.
Meaning that this PDF will remain with you for life.
You can download it as many times as you
want. I hope
you liked today's video.
Thank you very much for watching this video.