866. Complete Guide to Trimming/Assembling a Teapot with Hsin-Chuen Lin

Hsinchuen Lin
205 followers
213 Video Views·Aug 4, 2025
To see or buy my finished work and pottery tools, please visit my Online shops:
https://sawfish-endive-kgks.squarespace.com/shop
http://www.etsy.com/shop/hsinchuen
http://www.etsy.com/shop/hsinceramics
http://www.etsy.com/shop/hsintools
To watch more of my YouTube videos, please visit my channel:
http://www.youtube.com/@hsinchuen
To learn more information, please visit my Website:
www.mypots.net
Instagram: @hsinchuenlin
Facebook page: Hsin-Chuen Lin Ceramics
Pinterest: @hsinchuen6518
I'm going to trim this teapot body, lid and the spout a little bit, so I'm going to use this part to trim the body first.
I will use the time-lapse mode to fast-forward and focus on the assembled part.
I will trim a little bit here, try to fit the lid, because I told you that I make my lid slightly bigger than the exercise.
I need to remove a little bit of clay from here.
I trimmed the lid right on top of the body so I can get to look at the whole proportion of the lid compared to the body.
To be able to do that, your lid has to be very tight.
I'm ready to assemble the spout.
I'm going to raise it up so I will be able to see it.
This is where I'm going to attach my spout.
You can see that the spout is not up to the size, so I will need to trim up excess clay so it will fit better and the proportion looks better.
I'm using my number 7 knife, which is very good to trim up the spout.
I use that to draw a guideline here.
I slowly shape up the clay.
I keep my spout a little bit on the softer side so it's easy for me to manipulate it.
I roughly trim it up and put it up to compare the size and the height of it.
This part here needs to go higher, so I will trim a little bit more at the top.
Sometimes you can put it behind it and see how you're going to cut the curve.
It's a little bit too big, so I will trim up more clay.
Now the size looks much better.
All I need to do is just fine-tune the curve so that it's fitting tight.
After I use my number 7 knife to shape it up for the final carving or final adjustment, I will use the teeth of the hacksaw blade.
This is the hacksaw blade.
I use that to slightly scratch the part that might not fit very nicely.
I use that to scratch the clay off.
Then I put it back on to test it.
There's still a gap here. I need to get it out.
I use that again to scratch it.
This looks good.
I'm going to make the fielder part thinner.
I'm going to make sure that this part is on a good height.
I'm going to hold it here and use my needle to copy the outline of the attachment along with the outer part of the spout.
This is where I'm going to punch the holes.
This is my hole puncher.
One hole, two holes.
I just gave myself a rough idea of where I'm going to punch it.
I make sure that the spout is straight before I compress it firmer.
That looks good.
Then I squeeze it.
The beautiful thing about getting your spout slightly softer is it's easier when you assemble it because you can always pinch it and readjust it.
I just use my plastic knife to compress it and then blend them together.
Then all I need to do is add the handle.
Here I usually cut the spout slanted.
Right now I will show you how I attach the handle.
I bring back my handle which is ready to attach.
I put the hole here.
I can see the spout, the knob and the hole.
It's a whole straight line so that I know where to attach the handle.
Go here.
Maybe a little bit here.
Let's go slip on pressure.
Let it sit for maybe five minutes to even out because the body is slightly drier than the handle.
If I blend them together it might not even out.
Usually after I put the handle on I will let it sit for maybe five more minutes so the body is going to draw more water from there.
After that I will just smooth it out.
Alright so this concludes my demonstration on trim, fit the spout, fit the leg, attach the handle.
This is the finished piece.
Thanks for watching and I will see you next time.
