I'm going to use this blue axis as the
axis of my drill bit inside the drill
press and the green red plane as the top
surface of my stock drill press table so
let's go ahead and draw that real quick
C for circle from here and my my
diameter of the stock drill press table
is 11 and 78 so half of that is 5.
9375 enter P for push let's push this
down just a nominal thickness right
there space bar triple click G for
component enter so that's my stock drill
press table I'm going to draw a couple
guidelines here to help me out t for
tape
measure and I know that from the center
of my drill bit to the the column of the
drill press is 6 and2 in so let's go
with 6.25 in enter and I know that I
want a front to back depth of uh 15. 5
in enter I know that I want a left and
right width of 30 in so half of 30 is 15
enter half of 30 is 15
enter I also know that because this is
11 and 7/8 uh the stock table is I want
about 12 in leeway uh room for this so
let's just grab right here and drop one
off half of 12 is 6 in enter half of 12
is 6 in
enter now I can draw my vertical pieces
I have all my Corners laid out R for
rectangle from here and let's just go
all the way to the bottom and just drop
it off you don't always have to put your
dimensions in uh while you're drawing so
my first Dimension looks like it's the
smallest so that is my left and right
and I can change my first Dimension by
First Dimension only of this particular
uh rectangle by just typing in 75 comma
I'm going to leave my second dimension
empty and it will it will use the last
second dimension that was used enter and
there we go fif Push Pull let's push
this down with a height of 8.25 in enter
spacebar triple click G for component
enter M for move control brings up copy
and now I can copy one right there now
that I have both of these I can space
bar hold shift to select both of these M
for move control brings up copy and I
can just cop copy both of these over
there I'm done with my guidelines so I
can delete
them and let's draw the first top
surface R for rectangle from here to
here P for Push Pull let's push this up
with a thickness of 75 in Enter space
bar triple click G for component enter
now this is just going to be put
together with pocket hole screws so no
uh no joinery is needed right there
there for uh drawing but if you wanted
to make a uh rabbit and dat type setup
you can do that very easily R for
rectangle from here to here and if you
want a quarter inch rabbit and data
rabbit and dat and your thickness of
your material is 75 in so that leaves P
of push pull let's push this down5 in
remaining R for rectangle and I'm just
going to outline these vertical pieces
real
quick just to give me some guidelines
here so now that now outlining left
three independent sections so P of push
pull let's push this up the remainder of
my 75 in which is25 in enter and I can
double click to repeat my last push pole
measurement so that's how you can make
the rabbit or dat construction if you
want I'm using pocket holes so let's
just go ahead and delete this that was
just for demonstration select this m
move control brings up copy from here
down to right there and that is the
basic frame of this drill press
table now let's add the actual top to
the secondary top R for rectangle and my
see my first Dimension is the longer of
the two so I can do 15.5 comma 4 in
enter P Push Pull let's push this up
with a thickness of 75 in enter now I'm
going to have a TR trck right here half
of a TR track is just a rabbit that's it
so let's space bar select this line down
here mam move control brings up copy and
let's pull this up 25 in P for Push Pull
and let's push this in. 375 in Enter
space bar triple click G for component
enter this is symmetrical so M for move
control brings up copy let's drag one
all the way across on the red axis
holding shift to constrain to the red
axis and drop it off at the other side
right click and flip it along the red
that's the direction in which we drug it
and now we have the rabbit on the inside
over here as
well now this the center section is
going to be removable and I want it to
be right in the center so let's R for
rectangle and just draw it real quick
quick and let's see let's go with a
first let's go with a width of 6 in
comma 15.5 enter P Push Pull let's pull
this up 75 in enter and space bar triple
click G4 component enter let's M for
move from this
midpoint and holding shift to constrain
to the red axis I want to drop from the
midpoint and drop it off on top of a
midpoint of the entire project so now
this is perfectly centered this this Gap
is the same as this
Gap I need a right side of my TR track
well I've already got one over here so
let's click this M for move control
brings up
copy and let's constrain to red and drop
it off right there push it away .25 in
and now I just need to extend this over
to here let's right click and say you
are unique you are no longer a copy
space bar double clicked edit the part
pea push pull from here to here space
bar and click outside so now I created a
new part that is a little bit wider M
for move control brings up copy and
let's just copy this one over to here
right click flip it along the
red so now I have a t trck up here for a
quarter inch uh Carriage bolt and same
thing on this
side the carriage bolts are going to go
through the fence so let's R for
rectangle and my entire width is 30 so
let's go 30 comma 75 enter P for Push
Pull let's push this up with with a
height of 2.5 in Enter space bar triple
click G for component
enter now let's mam moove control brings
up copy copy one side by side and I'm
going to have a hole right here with a
carriage bolt and a kn but there's no
sense in getting crazy with the drawing
here so let's see a circle and let's
just eyeball this just for
reference P for Push Pull and yeah
that's fine space bar triple click G for
component enter that's the knob on top
of the carriage bolt there m for move
control brings up copy and there's also
one on this
side now if I move the fence I want all
my parts on the fence to move as well so
let's hold shift to select all of these
G for component enter and now they're
all one big giant component so if I M
move I can move the entire fence as
needed now let's work on the drawers
actually let me back up for a second I
forgot the drawer fronts are going to be
3/4 of an inch so all of these pieces
need to overhang by 3/4 of an inch let's
double click that at this part P for
Push Pull let's pull this out 75 in
enter you can see that's a copy back
there so it updated as well space bar
get out of that part same with this one
double click P for Push Pull and I can
just pull it out to this face space bar
to get out of the part double clicked
edit this one p for Push Pull and I can
just pull it to that face so there we go
that's my 3/4 inch overhang that I
forgot to add
earlier I need some drawer Runners for
the top two drawers down here so let's r
a rectangle from this back face up to
this front face looks like my Dimensions
say the second one is my length so let's
go with
0.5 comma 15.5 enter P for Push Pull
let's give this a thickness of 0.5 in
Enter space bar triple click G for
component enter M for move I'm going to
grab this midpoint and I'm going to drop
it off on the midpoint of the vertical
piece M for move control brings up copy
I'll grab over here and constraining to
the red axis I'll drop it off on this
side space bar holding shift to select
my other one I have both of them
selected M for move control brings up
copy and I can grab from down here and
drop them off down
there now let's draw the drawers real
quick uh just going to use half2 in
plywood here so R for rectangle from
here to here P for Push Pull let's push
this all the way up to the top and I
want a 1/16th of an inch spacing so
let's k for my hidden lines and you can
see I'm grabbing the top here I'm we
push it down 1 / 16 enter can use K to
get rid of my hidden lines space bar
triple
click G for component
enter now I want this to be a little bit
of leeway inside this cavity here so
let's mam move let's move it away from
that that wall
by uh 1 / 16 1/16 of an inch that's
fine M for move control brings up copy
and I'm going to grab that side holding
shift to constrain to the red axis and
I'm go all the way to that side now
these are just identical Parts real
quick but I want to have a left and a
right so I drug it across on the red
axis let me right click and flip it
along the red axis and you'll see why in
just a second
let's hide some of this other stuff real
quick I don't need anything else in my
way to draw this drawer so
let's hide all this so here's basically
my drawer and I want to
have a Groove along the bottom for this
bottom bottom tray to sit in so let's
edit my part grab this bottom piece M
for move control brings up copy let's go
up 375 in enter and let's go grab it
again and press controll go up again 25
in
enter just made a little Groove real
quick P for Push Pull let's push this
in uh 0. 25 in
enter now you see it updated on the
correct side over here my my right side
over here and my left side over here and
that's because I flip flopped them
earlier uh when I flipped along the red
axis so that was that was the reason for
doing that space bar click
outside now I need a drawer front a
false front so let's grab one of these Q
for rotate and let's rotate this
pressing control to make a copy in the
correct orientation M for move and let's
just move it in place now it's way too
long so let's right click and say you
are unique you are no longer a copy so
you don't update the others space bar
double click to edit the part
P Push Pull and let's push this in right
there and that's the front side of this
drawer with the tray the little Groove
in the bottom for the tray for the
bottom uh lining up perfectly so let's
grab this mam move control brings up
copy and let's set another one right in
the back we drw it along the green so
let's right click and flip it along the
green
uh I pressed the wrong axis right there
but actually that's that's little
irrelevant right now anyway um let's
right click and say you are unique and
we're just going to chop all this stuff
off at the bottom anyway so let's k for
my hidden lines and I don't know if you
can follow me here but I'm going to
space bar double click to edit the part
Alpha line and I'm just going to draw a
horizontal line at the top of my groove
in this back piece that way I can P for
push pull from down here and you can see
I'm chopping off that entire bottom
area space bar click outside of my part
K removes my hidden lines and all I did
was chop off that bottom area there's an
extra line in there I guess I could
double click and delete that line real
quick but there we go that way I can
assemble the drawer and then slide the
bottom in and then just screw the bottom
to right
here oh well let's make the bottom real
quick I forgot about
that uh let's go with our for
rectangle from
here to here multiple ways of doing this
I think I'm doing it the hard way right
now all right so I'm dragging this
bottom piece all the way out to the back
and I'm going to drag this side out to
here
and I'm going to drag this side out to
there space bar triple click G for
component
enter so there's an accurate
representation of the drawer now just
like the fence if I want to move one of
these I want to move to every one of
these so let's select all this right
click and say you are a
component
create there we go let's unhide the rest
of my stuff
edit unhide
all so there's one
drawer and let's M for move control
brings up copy let's drop the next
drawer whoops drop it down there space
bar hold shift to select both of these M
move control brings up copy from this
point over to there so now I maintain my
1/16th of an inch spacing on the sides
as well as the top and I've got all four
drawers really quick the only thing left
to do is make some very easy drawer uh
drawer fronts so Offa rectangle from
here and I want to stop in this
midpoint P for Push Pull let's push pull
this rather with a thickness of 75 in
Enter space bar triple click G for
component
enter M move control brings up copy
and you know what if I set this up here
I think it's just going to be way too
much uh not enough space rather so let's
space bar double click and let's P Push
Pull let's go down 1 / 16 let's go down
a 16th of an inch space bar to get out
of your
part M for move control brings up copy
and I'm going to set one right up here
on the midpoint so now I have a 16th of
an inch spacing here 16th of an inch
spacing there those are my drawer fronts
space bar hold shift to select both of
these and for move control brings up
copy and I'm just going to drag these
along the red axis over to
[Music]
here that's it that's the drill press
table the fence is adjustable on these
two t tracks this Center section is
sacrificial and floating it will be
removed as needed and you have four
drawers for storage