up to this point I've completed the case
construction and base construction of
micron of inspired coffee table build
and in this video I'll cover the final
details the surface prep assembly and
the finish all of the outside edges of
all of the crowded joinery will get a
chamfer and with the case still in a dry
assembly it is a good opportunity to run
a plane over both the pins and tails at
the same time now I won't be able to you
know plane the chamfer around all edges
well assembled but this will give me a
good idea of what looks good when it
will be assembled and how deep the rest
of the cuts of the chamfers need to be
when it's disassembled I also used a
chisel to cut half of the opposite
direction chamfers just to get a better
idea for how it would look once I was
happy with the chamfer depth
I used a straight edge against the
outside of each joint to draw a
reference line now this is just a just a
visual guide to keep me mindful of the
joint depth when I cut the chamfers
these joints were really really tight
when assembled and there isn't much
vertical space on the inside for
disassembly so luckily the the joints
were cut proud which gives just enough
material on the outside to break apart
the joint I started with the pins and
went back and forth using a chisel on a
block plane and now I've used it I've
used a chisel on a previous project to
cut the chamfers but this mahogany just
wasn't cooperating too well with the
chisel the mahogany was cutting great
but it was a little bit more delicate
than what I was used to and I was
getting a little bit of tear out on the
backside so I switched to a hand plane
for everything and it's pretty easy to
get very very consistent results so long
as you you lock your wrist and only use
your elbow or shoulder to move your hand
the further away from the cutting edge
that the pivot point is the more
consistent results you'll get and the
more you changed the angle of your wrist
the more you'll accidentally change the
angle of the chamfer face and here's a
good look at the completed pins
I did have one casualty though on one
side of the side half pins I had a nasty
bit of tear out that I think was caused
by a tiny crack in the wood that I
didn't really see but this tear out
would have been just painfully obvious
when it was all completed so I went
ahead and repaired it now I wish I would
have recorded the repair process but I
instantly went into a pair mode and just
forgot all about the camera so here's
the repair being glued into place and
what I did is I made a straight cut with
a dovetail saw to remove the tear out
completely and that left a flat glue
face and then I cut a similar wedge
piece out of a previous off cut and just
glued it into place and then trimmed it
flush as needed if you take your time to
really look at the grain to find the
best green match then the patch will
pretty much disappear and if you look
really closely you can see the patch in
this case but but you have to look
really really close which is exactly
what you want nobody is ever going to
know that this was patched after that
it's rinse and repeat for all the tails
and here's a look at all of the tail
chamfers and here's a look at the case
tenon champers and it's more of the same
with the base tenon chamfers lots of
chamfers finally all the chamfers are
complete and the surface prep can begin
now the long rail coves were the only
thing that we're sanded by hand on the
base and I've started with 80 grit and
then worked my way all the way up to 320
grit
then every flat face on the base pieces
is planed with a smoothing plane and I
tried to do as much surface prep with
hand planes as possible because it's
it's so much faster than sanding even
when using an electric sander also
imagine of all those shavings were on
the bench in the form of dust not saying
you know throw hay or sandpaper or
Sanders it's just issues them as little
as possible hand planes and scrapers
they'll save you a tremendous amount of
time and right after saying all that I
get to tell you that I used my random
orbit sander for all of the mahogany
pieces I tried my smoothing plane first
but I wasn't liking the resulting
texture on the quarter sawn areas of the
mahogany it just wasn't planing evenly
across the panel some some areas that
were kind of flats on some areas that
are kind of quarter so on it was just
it's just easier to get more of a
consistent result in this case by using
the random orbit sander next up is
actually the finish I wanted to do as
much of the finishing as possible before
assembly and the reason is once
assembled there's going to be a lot of
hard-to-reach interior corners and with
the finish applied before assembly any
glue squeeze-out
that all that's gonna be a lot easier to
remove for a finish I'm using armored
seal satin now my wife and I feel like a
gloss finish feels a little bit too much
like plastic and satin feels closer to
not having a finish if that makes sense
almost like it allows the wood grain to
do more of the talking rather than I
guess a shiny film finish now obviously
I made sure to not put any finish on the
glue joints but I did put finish on the
proud areas of all the Tenon's this
again will make glue cleanup a lot
easier after two coats of finish the
glue up can finally begin and all of the
joints on this project were really tight
to begin with and they all required a
mallet to seat them in the dry assembly
so if water-based PVA glue is used for
the the final assembly the joints would
actually swell just a little bit and be
even more difficult to seat so instead I
used hide glue which is it's somewhat
acts as a lubricant to help receipt the
joints I actually worked out really well
I was able to assemble all of the bass
joints by hand without using a mallet of
course I used a mallet to kind of tweak
the angle a little bit just to make sure
everything was square but as far as
seating the joints all of that I was
just able able to just press it all
together hide glue in this case is
definitely the way to go there's one
final thing to do on the case before
assembly and that is a little relief cut
needs to be made with a chisel on the
inside edge of each of the tails this
doesn't really affect the strength of
the joint but it does allow a little bit
of glue relief area because sometimes if
the joint is really tight to begin with
which in this case it is the excess glue
can prevent the joint from seating all
the way if this relief cut isn't made
but even with the hide glue these cased
joints were still pretty tight and
required a bit of persuasion to close
them up and oh yeah my brand new Harbor
Freight two-sided mallet fell apart
which is always fun
after assembly all of the joints on the
front and back face of the case were
flushed up with a smoothing plane and
then all of the edges were broken with
320 grit sandpaper I decided to leave
the top Tenon's on the case proud as
they could always be flushed up later if
I didn't like it but on the bottom I
went ahead and planed them flat and then
sanded them to I guess better blend them
with the bottom of the case which is
kind of pointless because due to
expansion and contraction of seasonal
humidity changes the Tenon's on the
bottom side are eventually going to be
you know you'll be able to feel them
with your hands and of course it's on
the bottom side it's never going to be
seen but whatever a couple more coats of
finish we're still needed so every
assembled exterior face on both the case
and the base were gently sanded with a
fresh piece of 320 grit sandpaper and
then vacuumed off before applying two
more coats of finish to attach a top to
a base I always use these tabletop hold
on clips they're really inexpensive and
you can buy them in bulk on Amazon and
they're super easy to implement a
biscuit joiner is used to cut the slots
and here you can see one cut in a scrap
block to verify the biscuit joiner setup
correctly the clip goes into the slot
and is secured to the bottom of a
tabletop with a screw the slot
connection allows the clip to not only
hold the two pieces together but it
allows for movement of the top as it
expands and contracts with seasonal
changes in humidity there's a few
different ways to make the slot but I
found the biscuit joiner to be the
simplest and most efficient once the
base is positioned on the top it's a
good idea to clamp it in place to make
sure it's exactly where it needs to be
as it is secured and finally the project
becomes a piece of furniture as the base
is joined with tub
I recently had a conversation with a
good friend of mine about this project
and he asked if I was nervous or
apprehensive about making it due to all
the design elements and all the
opportunities to make mistakes and my
answer was it was an immediate and
confident no probably the most involved
piece on this project is the long rails
with dual coves and offset chamfered
through Tenon's and that kind of sounds
like a mouthful to say when you think
about it as a complex piece on you know
on the design paper but it's much less
intimidating if you approach everything
by just saying saying what it is in its
most simple form you know this is a cove
cut on the table saw that's not too
difficult this is a simple curved cut on
the bandsaw that's pretty easy to do
this is a tenon cut to one side of the
board those are all straight cuts to
form a rectangle and these are 45 degree
chamfer which are pretty easy to do with
the hand plane so no matter how complex
something might seem at first you can
always be broken down into very simple
tasks and here it is in my living room
and I think it needs one or two more
coats of finish because it shows up on
camera a couple of spots that I think I
missed but I can do that at any time it
also obviously needs the drawers but I'm
a little undecided on a couple of the
details so I'm going to take a break
from this project and come back to it
and a little bit and also a big quick
shout out to my good friends at City
hardwoods in Birmingham Alabama
they provided most of the lumber for
this and also the finish for this build
so definitely check them out if you
drive through Birmingham Alabama and if
you have never been there before be sure
to tell them that J sent you not because
I gained anything by doing so I don't
but as a small business owner myself I
know that it's it's incredibly valuable
to know where your traffic source is
coming from so anytime you're in
Birmingham Alabama
check them out you'll be glad you did
that's it for this video subscribe so
you don't miss the next video if you
haven't already done so check out my
website JC custom crashes calm and sign
up for my email newsletter to keep
up-to-date with everything that I have
going on you guys take care have a great
day and I will talk to you in the next
video
[Music]