Dremel Wood carving an Eagle

Carving Art Channel
11 followers
3 Video Views·Jul 13, 2025
My first wood carving of an eagle. Im thinking this is a great project if your trying to learn how to carve an eagle.
So it's good to start off with a relief carving as opposed to a 3D carving when you're first starting out and eagle is a perfect subject to do that.
And the best drawing you can have is one of a profile of the eagle head.
You don't want kind of like this where it's sort of shot from down below.
It's no good. This one shot from down below as well.
And you can also sort of like put in line drawings on the computer.
But these are good pictures to use as references just to see how all the nasal kind of things work as well.
I used sort of baking paper as tracing paper to take this off an eagle that I found on Google.
I can't show you that eagle, but I've kind of changed it around a little bit as well.
So I'm not infringing on any copyright laws.
So then I just put a little bit of carbon paper on and go over the pencil again.
And we have got a copy of that now on the wood.
OK, and we're going to power carve the background back to a flat surface.
So on the side, I want to sort of like put a line in where the background is going to go back to my go a little bit deeper there.
You can sort of see I'm just using my finger and the pencil to go along.
So that is the area of wood that we're going to take away.
Now, there are a lot of ways you can remove wood.
And one of those ways is with a cutter burr.
But however, I kind of think it's kind of a little bit of a waste if you remove a whole lot of wood with a cutter burr because they tend to dull really easily.
So I tend to only use cutter burrs for fine details.
But you could use it if you want.
If you've got some cheap ones, you can use that.
Or you could use a Kutzel Extreme Burr.
You could use the Flame Burr if you wanted and just keep that moving really, really quickly.
And you could also use this burr.
This is a Kutzel Sphere Burr.
I believe it's the largest one in the 1 8th category.
This is an extreme one as well.
And it's removing it really, really nicely.
The thing when the burrs are a little bit bigger, it's easier to get that flat surface on the wood.
And I'm using sort of like that sponge there under my hand and sort of going along.
And so I'm sort of like not doing it free, like in a free hand.
Not like holding the carving up.
So I'm sort of using the table as sort of like a level surface.
So I can sort of just go in and try and get everything going down at kind of the same rate.
Does that make sense? I'm not really sure if it does.
But anyway, you can sort of see what I'm doing.
And I'm just sort of like checking to see if I'm going up to that line.
And what I tend to do is sort of like go quite close to the eagle, sort of the lines that are drawn around the outside.
But I'll tidy those up as I finish off this background a little bit later on.
Now we have removed the bulk of the wood from the background.
I could go back in with a cutter burr and just smooth it out.
And I'm kind of using that sponge again to sort of keep my burr level and just move the carving over it.
Yeah, it's one way of doing it anyway.
It's not the only way, but I just sort of work quite well on this eagle carving.
OK, so to remove that little bit in between the beak and the body, I'm just using the Kutzel Fine Sphere Burr,
the smallest one that Kutzel has got.
And I'm just sort of like going back into the carving with that.
You can control that very, very easily.
And it just fits in between the beak and the body.
So that's what you're kind of looking for when you're sort of choosing a burr, that it can fit into the place that you want it to.
So I'm sort of like taking it back to the background, and then we'll use some other burrs to sort of like fine up the lines.
And I'm using my favorite Kutzel burr, and that is the Fine Taper Burr.
I think everyone should have one of these.
Just really, really good for sort of like fine details, getting into sort of like tight areas, undercuts and all those kind of things.
Yeah, so that is the Fine Kutzel Taper Burr.
And you can sort of see that I'm just using the tip there to sort of get closer to the lines.
OK, so I'm pretty happy with the background.
I'll probably tidy it up a little bit later on.
But now I'm just sort of like looking at that reference point with the eagle, sort of deciding on what's the highest point.
It's that bit above the eye, and then the eye needs to be a little bit submerged into the carving.
So I'm just sort of like looking at the relationship with everything, sort of I need to take the beak kind of a little bit back and round it off.
And with relief carvings, you've got to understand that you can't sort of like go 100% 360 on them.
You sort of have to sort of taper things back a little bit and maybe just sort of like insinuate depth in some parts.
And here is a little Dremel disc sander that I got off Amazon.
It's pretty good for these backgrounds and just flattening things off.
You can sort of put different grits on to make it smoother or, well, you know, the like.
I think I've got 60 grit on there at the moment just to sort of like smooth things out.
And then I'll go, I don't know, to about 120 grit probably.
And it's back to using that taper burr.
And now I am just rounding off the beak with the side of the taper burr, give it a little bit of shape.
And I sort of like try and do things that I kind of know what it's going to look like to start off with.
So I know the beak is going to be round and the top of the head is going to be sort of like the most prominent part.
Because then the eye is going to be sort of submerged under that top kind of eyebrow there.
So I might carve the top next.
So let's do that.
And this is what happens if you lose control of your Dremel.
And so you can sort of see what happened there.
I sort of lost grip of the Dremel and then it sort of like flew out of my hand and hit the thing.
And then hit my T-shirt and wrapped up and stopped the flex shaft.
So that broke the inner shaft of it.
And so I just replaced that and then we will carry on carving.
I guess it was lucky that I only had the fine taper burr on there.
And now I've got the fine cut cell sphere burr on.
And this is great for kind of shaping some sort of like leaving the eyeball kind of there.
And sort of taking some depth underneath it out.
Just sort of putting in sort of like contours on the upper part of the head.
Now I've got in a cutter burr.
And I'm just starting to shape the eye now with that cutter burr.
Got to be very careful with cutter burrs.
Because if you put too much pressure on them they can sort of like really cut into the wood really quickly.
So probably would suggest maybe a diamond burr if the wood is quite soft.
But like if you go really lightly the cutter burr is quite nice.
But yeah you do have the danger of taking too much off.
So yeah just shaping that eye.
Sort of like getting it sort of a little bit more submerged under that sort of like eyebrow of that top part.
And then we'll go and put details in.
Now I've kind of got that really elongated diamond cone burr on there.
That is from Master Carver.
And I'm just trying to shape that eye.
It's proving a little bit difficult there.
But you sort of you just got to persist.
And I'm using the end to put in sort of like the eyelids as well.
And sorry about this.
The camera work isn't the best.
It's kind of a little bit fuzzy.
But you can see my fingers really well.
So but what I'm using here is one of those.
What are they called?
The T-shaped burrs.
Sort of like with a flat disc on the top.
Sort of like sort of smoothing out the eye itself.
And putting in sort of like the lines there with the edge of it as well.
It's quite a delicate operation.
So I've just used a cutter burr to put in the sort of like details of the feathers.
I haven't gone into great details on each individual feather.
But I might put in just a couple of feathers sort of down the bottom.
To sort of show you what a feather can kind of look like.
You don't have to put them all over the body.
Yeah so that's what I've kind of done there.
And sort of just added a little bit of depth behind those feathers.
And if you really want your carving to sort of stick out.
What I do is I will put a sort of like undercut.
Between the background and the body of the bird.
Or whatever you're carving.
So you can see it there.
It's really quite nice.
So I've used those T burrs.
And they're really really good for that.
And it also offers the advantage of the wood dye doesn't soak into the bird.
Because you've got that really big undercut underneath it.
Okay so that wood dye is a Brie Wax.
It's called Antique Mahogany.
And what I'm doing here is really sort of like giving a contrast.
Between the bird, well the eagle and the background.
And what I'm doing now is I am putting on a wax.
And pretty much that's it.
And so you could paint it or burn it or however you want to do it.
And so to bring out the eye detail and maybe a little bit on the beak.
I just go back with a diamond burr.
And so we don't have to paint or anything.
I'll just bring it out a little bit so it kind of sticks out.
And if you could hit that like button that would be fantastic.
And I'm not quite sure what I'm going to carve next time.
I'm thinking maybe a skull.
What do you reckon?
Bit of bad camera work there.
Anyway, hey thanks for watching.
We'll see you next time.
