AC Fan Outside Not Working - How To Check It

TV Electric Fan
2 followers
7 Video Views·Jul 7, 2025
Is your AC fan not working or spinning? It's possible that it is simply not getting power or that the capacitor is dead but the condenser fan motor itself is good. In this video I show you how you can check your AC fan motor to see if it is good or bad.
Hey guys, Jay here with Word of Advice TV.
I get a lot of questions in my comment sections
how to check a condenser fan motor, if it's bad or not.
And really, it's pretty simple most of the time.
I mean, if your capacitor is good,
if you verified that your capacitor is not the problem,
usually it'll be just one capacitor or dual capacitor
where it's for the compressor and the fan.
Sometimes it'll be a few different capacitors.
Just track down the one that has
the condenser fan wires going to it,
and that will be your fan capacitor.
In my case, I have a dual capacitor,
and here's my fan section right there.
And I know my capacitor is good, I've checked that.
But if you haven't checked your capacitor yet,
I have a video in the description that you can check out
on how to check and replace your capacitor.
But anyway, if your capacitor is good,
and you verified that you have 240 volts going to the unit,
and if your compressor is turning on,
then almost guaranteed that your
condenser fan motor is bad.
But if you wanna know for sure, I can show you.
So for example, if you have power in,
your disconnect is plugged in,
your AC breaker is not tripped,
your fuses inside the disconnect are not blown,
you set your meter to voltage,
and where your line voltage is coming in to the AC unit,
which will be these two screws right there,
put both leads on those two screws
to verify that you have 240 volts going in.
And as you can see, we do have power coming in.
So once the thermostat calls for cooling,
that little plunger will pull in
and send the 240 volts through.
And both your compressor and your fan should turn on.
If your compressor is turning on and the fan is not,
then potentially your fan is bad.
Now if you wanna confirm that it for sure
is your fan motor that's bad, you will need a meter.
So the way you check it is pull out your disconnect.
To be safe, you can turn off the AC breaker
inside the house and turn your thermostat off as well.
And then I like to just be safe and verify
to make sure that there's no bad wiring or something
and I still have voltage, just with a voltage pen.
And it's not beeping at me, so there's no voltage anywhere.
I'm safe to disconnect whatever I want.
So what you will need to do is either look
on the back of your door if you have a wiring schematic,
see what colors go to the fan motor and what wires,
and then track them down inside of your electrical section
and see where those wires go into.
If you don't have a schematic,
or if you just wanna do it the manual way,
if you look at your motor on top,
see how there's this sleeve right here?
That holds the fan motor wires inside of it.
And that will go right in here and come out right over here.
So if you want, you can try tugging on them
and see if you have any action on the other side.
I already traced mine down.
So this is a fan wire, this one right here
going to the common is a fan wire,
and then this guy right here is my fan wire.
Now before you go and start disconnecting them all,
I would either take a picture or label where each one goes
so that you remember where to put them back.
So I'll disconnect my wires,
I already know where they all go.
Once you have all three wires disconnected,
you can check resistance and see
if this motor is bad or not.
Okay, so you'll be checking for resistance
between all three of the wires.
So you should get three readings.
So let's start with the purple one,
which I think is my common.
So one lead on purple and one on the brown.
I suppose it would help if my meter was on.
There you go.
Gives us a reading of about 138 ohms.
Then I leave my purple one connected
and check between purple and black.
That one gives us 70, let's call it 74 ohms.
And then you want to check between the last set,
which is brown and black.
And that gives us about 79 ohms.
So those two smaller readings, if you add them up,
they should equal about the same as your common winding,
which is that biggest reading.
If your readings do not add up,
that means your condenser fan motor is bad.
And a lot of times when your windings are way off
the readings are, you'll have continuity
between the connectors if you just take one wire,
or let's say the brown one, and then just go to ground.
If you find where one of your green wires goes,
that'll typically be a ground,
or you can just go straight to the casing
or to the ground screw.
A lot of times you'll actually find that there's continuity
between your fan wires, or at least one or two of them,
and that ground wire.
If you have continuity, see how mine says OL,
there's no continuity between this winding and the ground.
If there is continuity, then for sure your motor is bad
and you need to replace it.
And after that, your checking is done.
If you did not take a picture or label your wires,
then you have to try to figure out where these guys go back.
If you did take a picture, then look at your picture,
put everything back together,
get yourself a new fan motor, and you'll be good to go.
And that is all I had for checking your condenser fan motor.
If I missed something or if you have further questions,
just ask me in the comments below.
I'll try to get back to you as soon as possible.
Thank you so much for watching.
Don't forget to mash that like button on the way out,
and we'll see you next time.
