Conserving Dürer's Triumphal Arch

Artifact Archives
9 followers
Follow the latest stages of the complex conservation process of Albrecht Dürer's Triumphal Arch – one of the largest prints ever produced. Curator Giulia Bartrum and Paper Conservator Caroline Barry talk through some of the steps involved in tackling this unusually large conservation challenge.
#GJWculture #Antiques #Mysteriousdiscoveries #Discovery #Artifacts
This is Durer's Triumphal Arch, which has been in the British Museum since 1837.
It is the largest print that we have, measuring some four square metres, and the challenge has
always been the storage and preservation of it. Clearly this is a print designed in paper,
it was designed for decoration and it would have been coloured
and posted up in baronial halls and courts of the Holy Roman Empire.
When it arrived in the department it was in five long strips, thereafter it was kept in portfolios
until the 1890s when it was assembled into one sheet, as was the original intention.
Since then it has been on permanent display, which is an extremely long time for anything
of this fragility, and it is just recently that we have the opportunity to remove it from the frame
and we have now got the opportunity with a generous donation of funds to
preserve it and to think about its long-term storage.
The first stages of conservation were really mapping the damage, so we used clear plastic
sheets to draw on and we started to get an idea of what we'd have to deal with.
The problem we faced was actually accessing the middle of the print, and this was a problem that
we also saw them dealing with in Copenhagen when they were working on their version of the print,
and we took their idea and ran with it, which was to have the large roller sitting on the top of the
table and the print moving along the table and down onto a secondary roller underneath the table.
Using this two-roller system we firstly cleaned the paper, which we call dry cleaning, which means
using erasers to take the surface dirt off. If you don't do that, any subsequent treatment using
moisture or water would fix that dirt into the paper. The print had been exposed under glass
since the 1970s, but before that time it had been displayed unglazed with the coal fires that you
find in the early 20th century, so we were expecting and we found quite a bit of surface dirt.
The print moved along the table and round and down onto the roller. At that stage we were able to
take more photographs and map more details of the condition of the paper.
So today I'm trying to find out what adhesives were used on the Triumphal Arch
print, because the conservators want to take off the backing, so they want to know what adhesives are there.
FTIR, Fourier Transform Infrared Spectrometer, and by analysing the difference between the
infrared light that we shine through the sample and the infrared light that gets to the detector,
we can then see what the characteristic material is.
The adhesive underneath was starch. We turned the print over and started to remove the lining.
We did some tests on what to use for this, using various types of humidity, and the best one we
found was holding the humidity in a gel which was cellulose-based, and that we could just put in
small areas on the back and wait till the moisture just worked its magic on the starch adhesive,
and then we could peel the textile off. We realised that the print itself was quite weak
once you took the lining off, so we had to then separate the sheets at the same time because we
didn't want to go through the second roller scenario, because that would be too damaging
to the weak paper. At that point we discovered that prints had been chamfered along the edge
as we tried to separate them. Somebody had very carefully shaved the edge of the paper off.
This made life quite difficult because the paper lost more than half its thickness. We were at the
stage where we have 36 individual sheets of paper and two small columns at each side of the bottom
are separate. The adhesive that was left on the back of the prints was very discoloured, and the
print surface itself was quite absorbent and some of the prints were noticeably discoloured.
So with that scenario with prints, there's a process of removing discolouration by washing.
The big advantage of doing this is that you remove soluble acidity, which over time is
harmful to paper. So using our special cellulose poultice again, we applied this to the back of
all the prints, using it to swell the starch adhesive and remove it with very smooth bone
folders, just to scrape it very lightly because we didn't want to affect the paper itself.
At the stage where we had removed as much adhesive as possible, we then put the print in a bath of
warm water, well supported and with two people handling them. The warm water was at the temperature
that would dissolve the starch and after a couple of changes of water, we could see that the yellow
discolouration coming out of the paper into the water was decreasing, and at that point we took
the print out and we left it to dry. We did that with all the prints and they're all more or less
quite a harmonious colour, although some of them are slightly discoloured and they're much more
they appear to be much more like the colour they would have been originally. There's a bit more
strength in the paper as well. We are now at the stage of repairing any tears and considering how
we will support areas like this that are very thin or where there are small holes, and we've
decided to use repair called pulp, which is how paper is originally made from paper pulp, and it's
taking that in a very more controlled way by using a solution of paper, a tone to the right colour
in water and a suction table, and to mask out an area that we want to fill like this skinned area,
and effectively we're making a small strip of paper ourselves which we will then lay on the print
and it makes a very harmonious repair which remains quite flexible and is ideal for small
holes as well. After the repair of the skinned and the missing areas on the print we are
going to line all the sheets with a very thin Japanese tissue which will support them
and it is the first stage to potentially joining the print back together again. How we go about
this and how it ends up is still open for discussion but it will be joined visually
in some way if not physically so the prints will remain in the conservation studio and
be perfectly safe here and in good condition until such time as we make a decision.
