What's up guys I'm Brad Rodriguez from Fix This Build That and today I'm going to show you how to
make a DIY bed with a ton of storage. It has simple joinery and materials that you can get from your
local home center. Stay tuned I'll show you exactly how I did it. The bed has four main parts to it.
The headboard, footboard, back, and the storage base. I started off by ripping the plywood down
and cutting the panels for the assemblies. The headboard and footboard are mirror images of each
other with a frame and panel look and the frames are made of two by fours which I'll clean up later
on the table saw for a more refined look. But first I cut all the parts to size on my mobile
miter saw station. There are a lot of repetitive cuts here and using a stop block is a huge help
to make sure everything fits just right during assembly. Above the panels there are some short
two by two accents which I'll be making from the shorter lengths of two by fours I'm cutting here.
For smaller cuts like this I use a 10 inch spacer on my miter stop since the stop can only go down
to 14 inches. I went ahead and cut the parts for the back assembly as well before the next step.
The long stretchers are a little bit longer than the capacity of my miter station so I clamped
them together and I gang cut them to make sure that they were all the same size. I don't really
love working with two by fours because they tend to be wet knotty and it's just hard to find straight
boards but with a little patience you can find some decent stock. And to get good joints on the
board I like to rip them down to three and a half inches wide to three inches wide and remove that
rounded edge. You also get some really nice kindling or shims from these off cuts. To get the
two by twos I make the same initial cut to get one straight edge then I set the fence to an inch
and a half and I make two cuts to get two pieces out of each of the two by fours. You get nice
clean edges but man they are sharp so to round over the edges quickly I clamp a hand sander down
to my bench and I ran each edge over the sander a couple times. If you don't have a router this is
a great way to get quick roundovers especially on softer woods. I also wanted a nice soft corner on
the headboard and footboard. I laid out a curve on the uprights using a fender washer and I took
the boards to my oscillating spindle sander. It made short work and gave me that rounded corner.
I'm using pocket hole joinery for most of this project so I set up my jig and went to town.
I'm using the K4 pocket hole jig from Craig, the sponsor of today's video. If you have a lot of
pocket holes to make the K4 or the K5 are going to save you a ton of time versus using those less
expensive handheld jigs. With the parts ready I started assembly of the headboard. I joined the
top and the side first and then I put the two by twos in place to position the middle stretcher
and screwed it to the side. Next I came back and attached the two by twos. I used a small spacer
to get consistent spacing between each piece and secured them to the top rail using a square to
make sure everything was aligned. I came back and secured them to the bottom rail using the
same spacer as well. The bed will rest on a half inch MDF panel on top of the storage frame.
I went outside and I cut the panel to length in the driveway using the Craig AccuCut track
and my cordless circular saw. I cut this part now so that I could use the off cut as a spacer for
the panel of my headboard. I put the half inch MDF off cut on the bench under the plywood panel.
I started in the corner and I worked my way around the panel securing it to the frame
making sure that both the panel and the frame pieces were clamped flat. I added the lower rail
and I attached it to the panel then I finished off the assembly by securing the other upright to the
side. The footboard is made the same exact way here so I'm not going to show that but I did need
to take care of all these pocket holes. Now this is a painted piece so I knew that any of these
exposed holes would be filled and I did a video on different ways to fill pocket holes. I found
the bondo was a great option for painted pieces. I mixed the bondo then I overfilled all the visible
holes and I came back and sanded them down flush after it dried. With the bondo drying I started
on the back and the back is just a large plywood panel framed by two by fours and I cut the panel
to size and I drilled pocket holes around the perimeter of the panel and in the horizontal
stretchers. From there I assembled the panel similarly to the headboard. I started with one
corner of the two by four frame then I added the half inch MDF spacer to position the plywood panel
just like I did on the headboard. I clamped everything firmly in place and then I secured
the panel to the frame with one and a quarter inch pocket screws. With the back panel assembled
the reveal on the front was exactly the size of that half inch MDF. To add some detail to the back
panel I cut two pieces and used them to match the size of the frame boards. I used glue and brad
nails to secure the MDF to the back of the panel and when it's finished off it gives the appearance
of three separate panels. The last part of the bed is the storage base. I made the base from two by
fours to keep the weight and the cost down. The base is basically a large framed box with three
sections for the drawers. I cut all the parts to size on the miter station using clamps and gang
cuts for the long pieces and my miter stopped to make repeated cuts just like before. I drilled
pocket holes in the vertical and horizontal supports to prep for assembly. Two of the long
stretchers and four vertical supports go together to make the back frame of the base. Clamping
everything firmly in place and making sure the parts are square will make things much easier
later. The front frame is made the same way except I left the outer vertical supports off.
Now this was purely for aesthetics and it gives the drawer bank a nice clean look when it's
assembled which you'll see later. From here I had to move to the floor for the rest of the base
assembly. This thing is big. I added the lower supports to join the front and the back frame.
I joined the top supports to the base frame next and these are laid flat and these are going to be
supporting that half inch MDF platform that the mattress is going to go on. The final piece of
the base is to add two small vertical supports to give the front frame support on the ends.
With the base frame done I moved on to the drawers. The drawers are made from three quarter inch
plywood and because they're so wide I decided to use a three quarter inch bottom as well.
I ripped the parts to width and then I cross cut them to fit the drawer openings.
I'm using pocket holes for the joinery like I do for most of my drawers and each of the fronts and
the backs gets pocket holes on the outside faces. Then I glued and clamped the sides to the front
and the back and then I screwed them all together. I typically use a quarter inch captured bottom
piece but I cut an exact fitting three quarter inch bottom for these drawers. Then I could use
the bottom as a lever to pull the drawer into square and use the front edge of the drawer bottom
to lock it into place with the brad nail. I secured the perimeter of the drawer bottom
with screws and it gave me a nice square beefy drawer that can hold a ton of weight.
I wanted to paint the base before installing the drawers so I went ahead and applied three coats
of sprayed on latex paint to the headboard, footboard, back and front of the base. After
the paint was dry I drilled pocket holes in the ends of the front frame which I'll use to connect
it to the head and footboard and then I set up to mount the drawers. I made some temporary supports
from the half inch MDF and three quarter inch plywood off cuts. The temporary support holds the
drawer slides in place and it also acts as a spacer at the same time. The drawers will have false drawer
fronts so I used a scrap piece of plywood to set the position of the drawer slide. The temporary
supports holds the drawer in place while I secure the slide extensions to each side of the drawer
in two spots. Then I pulled the drawer out and secured the back of the slides with another screw
on each side. Now I'm pretty happy with how well this little temporary support worked out. I repeated
the same process the next two bays and installed all three drawers pretty quickly. I measured each
drawer opening and I ripped the drawer fronts to height and then to the width on the table saw
and gave them a paint job before assembly. The drawer fronts are inset so I used playing cards
to get a consistent reveal around the drawer. I pre-drilled eighth inch holes in the fronts of
each of the drawers which gave the screws a little wiggle room for minor adjustments once the bed is
in place. Then I attached the false fronts to the drawers with one and a quarter inch screws.
I laid out the drawer pulls by marking the center of the drawer front on a piece of painter's tape.
I'm using the Kreg cabinet hardware jig to drill the holes and it makes it very easy to set the
size of the pool and the height that I wanted. I clamped it in place using a scrap block on the
inside of the drawer to prevent blowout. Then I drilled the holes for the hardware and installed
the drawer pulls with the longer of the two screw types included with the pulls. Now that's it! Now
it's just time to assemble. I moved the parts up to my daughter's room and I laid the base down. I
used two by fours under the corners of the base to get a relatively flat reference surface versus
the carpet that it could be sitting on. Then I raised the base another three and a half inches
by propping it up on two by fours on edge. I put the footboard in place and then secured them with
pocket screws and two and a half inch wood screws along the bottom and back of the frame. Then
brought in the back panel and it secured to the base frame and sides with pocket screws from the
back. We brought in the half inch MDF and I laid it down on the bed frame. To hold the mattress and
the MDF sheet in place I attached a one by three to the front edge of the frame. I finished up by
installing the drawers. My daughter is absolutely ecstatic about her new big girl bed. The large
storage drawers down below can hold a ton of toys for quick cleanup when it's time to put things away.
I want to give a big thank you to Kreg tool for sponsoring today's video. There's links down below
in the description to all the different Kreg tools I used that made this project a lot easier. If you
want to build your own storage bed there's a link below in the description. They'll take you to the
plans. They have detailed instructions with 3D diagrams, parts lists, and everything that you'll
need for the build. If you're not subscribed to the channel already I'd love to have you
as part of the team and until next time guys get out there and build something awesome.