Autodesk Inventor 2025 - Tool Post Holder Tutorial

Hey guys, welcome back to the youtube channel. So quick one this um specific assignment has been giving me issue i've been trying to create videos but Few dimensions were missing because by the time I found Hey guys, welcome back to the youtube channel. So basically this video i'll be creating i'm gonna be giving myself dimensions because I Tried creating this video long long ago, but few dimensions were missing and that's caused delay for release of the video. So I'm just gonna be using dimensions. I think it's meant to be based on what I saw on other um pictures From other engineers and all so i'm just gonna assume few dimension were missing but this video is just going to show you How to draw and probably if you know the right direction you should apply it to your drawing So let's go quick into it. So as always you click on plus to sign and i'm sorry I'm not going to be editing or cutting. So anytime I make mistake and I reverse my step the lengthy video We are all going to be together Um in it because I have no chance where I'm asked to start editing videos and all So on the height we do we have been told from the ground floor to the top is one one two millimeter and we have thickness of 46 Yeah 46 enter expand Then we are drawing an n pick your line to draw These make sure your lines are straight touch the floor touch take it up Back to that same height and connect to the wall right click Okay, then you come to your dimension to we're going to the distance to the floor is six mm Drag it out Six mm enter there are being told the distance from here to here is 12 millimeter to enter They were being told from here to this side is 18 or no 16 16 enter also I'm sure this part will be 18 or you can first check then I come to my trim tool And there's meant to be something like an end here, right but I don't understand the measurement that is given here three times one I don't understand what that is But what do you think? What do you think? Let me just draw an end there so we don't come back To draw make sure you don't omit the end that is being drawn here I'm, sorry, let me reverse my stuff Pick my line. So again, hello my keyboard Pick on draw Draw sideways and draw downwards I think what I just drew looks okay. Come on. Let me check the dimension of what I drew. Yes Three point Five three point nine. Let me just make this four enter That was the height of what I just drew So this is one nine, let me just make it two So yeah, i'm doing four by two Remember, I said my dimensions are not gonna be correct. I'm just doing it For doing six just to show you things that are to be drawn. I can't read most of the dimension that is written on the screen enter Take to the side I need four mm enter then connect background 20 degrees right click. Okay, let's zoom out I pick my codes to Begin to trim off places. I don't need Please if you can read the measurements kindly say something on the Comment section or in the comment section. I mean, uh, so we can all learn And correct our mistakes. So let's extrude Or is it too quick to extrude? Sorry scale out So I pick on my extrude to Yeah, extrude that portion, but I want it to go backwards With distance 64 Six four And yeah, so we are done come on this surface add sketch Sorry Yeah, um At first of my line so don't draw on the edge just somewhere outside the edge draw a slant line Make it longer than both edges Okay, then we'll pick our dimension to from here to here Is 70 degrees that's 70 plus 20 is 90 so 70 degrees enter Yeah, so um a book I saw right from here to the down part was is the same thickness as That of the slope. So I think i'll be doing the same thing and pick my trim to Trim off the ss portion. Yeah I'm, sorry I think I have to Put dimension on both sides So hold it down 70 as well Accept trim to And trim off this portion So, like I said the distance of the slope, um thickness of the slope during x3 rampage Which is 18 is the same thing as the ita In another diagram I saw so i'll be doing that because I don't know the distance Then we know from this down to the top of the slope is um 18 Yeah, but if you know the right dimension, like I said earlier Use it and also comment down in the comment section below. Um, what next I pick my line to From one edge of the box To another edge of the box on the straight line Yes perpendicular Okay, then pick my dimension to from the top to the bottom And 20 enter Yeah, then let's finish sketch for now pick our extrude Touch this portion. So we want to cut but inwards And not 64. I want to cut 18 Yeah Okay, it looks like i'm making progress. So do we work at the top or Okay, um, I think we have fillets um everywhere Which is Two radius two so fillet Yeah, two diameter I want a few here I want a few here a few here Yeah, I think it's around the frame around the biggest box frame All the time I am using I think I have to Portion as well. Yeah around the biggest box and click on my okay And Do we work here for us to work here? Um, let's work here. Remember it's always add sketch not any sketch. So at the top here I've been told there's a center circle distance 20 and distance nine distance 20 distance nine Distance 20 so I pick my let's pick construction line then line i'm drawing the first line This direction I'm drawing another line in And this again, this is the center This direction As you can see gave me the center so I did not so I do not need to measure i'm picking another one the straight line This direction so I pick on my dimension, too So I don't need to divide this because this is already the center Here to the edge i'm being told is 20 So I do 20 Therefore this guy to the edge I'm being told remember you're touching the final edge. I feel it should give us two edges. So you're touching the final to the other Edge is nine And Draw radius 10 because of the diameter of the boat another radius 10 plus The boats are straddling through the center Distance is diameter 10. So pick this I touch my center Center and this line so yes, then pick my dimension, too from this center to the center I was told This 40 mm 40 Okay, so extruding it now we pick on this guy these two guys Are gonna cut But through the thickness of this Then we click on plus sign Which is this guy Who is going to cut through all down to the end? Okay, then these two guys are treaded These two guys i'm trading here Okay Remember i'm using m10 1.5 Okay So this is not um, this this hole is not It's not shredded. It's just a normal hole And let's see yeah sitting exactly on the center of that point Cool, so we rotate to the front now to draw a circle Okay, so this sketch add a sketch create a sketch make it a size So I pick my line, too All right, I draw A minus line Don't worry i'll be raising that at the end of the day so i'm being told from This point to this point Is 30 So I pick my circle to Turn off construction line Then come somewhere diameter 11 enter Then come again Diameter 8 enter Right click. Okay dimension line from the center to the wall first hold Is 9 mm. Sorry 9 enter Right click. Okay Yeah, what else are we trying to do nothing so let's explore it to explore it I know for this big circle For this small circle, it's going to be true all codes sure Yes, and click on plus sign for this small right click and just this Is going to be called distance Six And So, let's see what we need I can see we still Yeah, that's where the boat is going to be sitting yeah, so our diameter looks okay back to normal So guys, this is all for this guy. So let's give it a color Um, i'll choose should I do black or yellow? Responding sorry, I have a lot of software running on the laptop and that's why it's hanging