How to make a heater shield

Shield of Antiquity
8 followers
20 Video Views·Jun 4, 2025
Comments are disabled for this video.
Greetings, I am Shad and you may have noticed that I use some wooden props in my videos.
You'll perhaps notice that I have some wooden sword replicas that I use as representations
when I'm explaining certain facts about medieval stuff, sword stuff and things.
You'll notice that I sit on a wooden chair in my videos and you'll also notice that there's
a shield behind my head and also another shield might have popped up now in my kite shield.
I built all those things and so I am about to start work on some more stuff and I figured
well if I'm going to be building things, you know, you might appreciate me doing a how-to video on
how I go about doing these things and so what I'll be making today is a heater shield because I
still need one. I have a nice big round shield, I've got a kite shield but now I need a heater
shield and so it's going to be just a very simple how-to video. I'll put some commentary over so
you see what I'm doing and hopefully you'll enjoy it, it'll help you out, maybe you could try
doing something like this in the future if you want shields because buying these things as I
found out is quite expensive. So if you want to go about, you know, having practicing hemer or
whatever that you like to do and you wanted a historically accurate representation shield
to use with it, you need to fork out a decent amount of money and oftentimes the other thing
I noticed is that you can't really get the shield exactly the way you want if you're the exact right
size or the exact hand hold and other things like that and so I found it's just easier to build one
and more cost effective as well. And so if you like me don't have a lot of money but you want
to be able to use a shield or whatnot in your whatever you want to do, reenactments, sparring,
fighting, cosplay, whatever you want to do, hopefully you'll be able to learn one or two
things from this video and so yeah sit back and enjoy. To begin with you're going to need some
plywood. Now the plywood that I'm using here is about a centimeter thick. Now not all shields will
use such thick wood and of course traditionally they never even used plywood, it didn't exist
back then, but what we're doing here we're making a historical approximation and so it's not to say
it's historically accurate but it's an approximation which means that we want it to
be as strong as a real historical shield, as heavy or as light in certain cases and so
that's what we're going to be going for. Not all shields were this thick, it really depends on the
type of shield that you're making. The viking-like shields, round shields, they're generally thin,
much thinner than people suppose and when you go to a kite shield they can be a bit of both but I
believe that you want them to be a bit on the thinner side because both of those shields are
much larger shields but the heater shield is a smaller shield and they were made to be thicker
and as to why well I'll explain that in a later video. So once you have your plywood you want to
measure the shape you actually want to measure out the shield and so what you'll see that I'm
doing here I've measured about 15 centimeters on the side down from the center point and that'll
give me the point of the kite shield and then I'm measuring the center all the way down so that's
the spine and from that center I'm going to be measuring the curve and now there's a
cool trick or a technique you can use in measuring the bottom curved point of the shield and
what you do you simply get a piece of string, stretch it from one end, well you first measure
down from where you want the string to begin and you measure or take that string to the
furthest side of the shield and measure that down to the center and what you'll notice there if you
do your measurements right it'll line up perfectly or it should line up perfectly
to that center line that you've drawn and so by stretching the string to the very opposite
end side and then putting that down or measuring it down with a pencil to the center you'll find
it gives you a beautiful bottom curve and point for your heater shield and the proportions will
just look wonderful. So I'm a bit of a picky person and I needed to measure it a couple of
times just because I wanted it to be the right size I didn't want it to be too long or too short
and so you might have to try it a couple of times I tried it a couple of times just to make sure I
got it right and so you know you measure it yeah take a look and then once you find a shape
that you're happy with well then you progress on to cutting it so the jigsaw I love the jigsaw
the jigsaw is a wonderful tool and it's just it's not you know when I say it's versatile
it's not versatile that it can do many things all it does is cut but it can do curving cuts
beautiful curving cuts and so I love the jigsaw out of probably any other tool I use the jigsaw the most
so there you have it there's the you can kind of already see the beginning shape of the shield now
with having cut that bottom part out and so you know against my arm you can kind of get an idea
of what this is already going to look like so the next step of course is to just jigsaw or cut off
the top to get the peak of of your heater shield and look at that that's pretty easy I mean just a
couple of steps you already have very much what looks to be a shield so there's the shape that I
went for and against me it's about the size I'm happy with and so that's the size I wanted it to
be now before we continue because the next step is of course to put the handle on the shield
and I just want to kind of add a caveat before I continue because the way that I'm putting on the
is not the way that you need to put on the handle okay there are a lot there are so many you know
there's so many simple ways you can do this you can just put a wooden handle on or just nail on
some leather straps or you know and so you'd be very simple another simple way you can buy like
a cupboard handle you know kind of the cupboard handles you see on kitchen cabinetry and stuff
some of them actually are a decent size that can substitute for a shield handle grip quite nicely
so there's heaps of ways you can do it so what you want to do is look at what the resources you
have available to you and then work with the things that you have available so for myself
I actually had available to me a forge yes a blacksmith forge and so that's what I used I
decided to blacksmith you know literally blacksmith my handles from some scrap metal
now you do not need to do it that way like I said there are so many other simpler ways to do it but
I wanted to do it this way for a couple of reasons it's not not to get an authentic thing no it was
so I could make a handle the exact size and dimensions that I wanted it to be I wanted a
with you know the grips that I was going to put onto the shield and when I say freedom I only was
doing this because literally I had this available to me and so I'm not going to complain if it's
there I'm going to use it now there aren't a lot of different strap or handle configurations that
you can put onto a shield and after thinking about it I decided I wanted to go with a metal handle
and hook which meant that you wouldn't have to tighten any buckles or straps you literally just
put your hand in grab it and then you're good to go and so that's the configuration that I decided
to go for with my heater shield and I decided to make them out of steel and again one more caveat
before we continue you know when I say that you know it might sound fairly impressive or complex
that I'm making this out of steel and I'm getting onto a blacksmith forge and working on this
I just want to say very clearly that I am a total noob when it comes to craftsmanship okay
if I can do this anyone can I'm an amateur at every single thing that you're seeing me do here
all you need is a basic understanding of design geometry and the basic have an understanding of
the basic principles of tools and then you're good to go and you can do this literally like
this is the second time I've only ever worked on this forge okay and so you just work it out as
you go also if you're wondering who that handsome older gentleman who that is who's kind of helping
me out everything that's my dad I'm doing all this in his workshop I don't own any of you know
these tools or anything like that but my dad is a well yeah he's a builder lifelong tradesman
and builder and architect and all that kind of stuff and so he's collected all these tools over
the years and so I have had I had the privilege to be able to use them and so I help myself to
his his equipment and stuff and so yeah the all the tools are his the forge is his this is this
is at the home that I grew up in I grew up as a kid and so I'm working in my dad's workshop here
now once you have the fire started in the forge you need to let it burn a bit to get the heat
heat going and raising and so once that while that is going I get my scrap iron scrap steel
and I cut it to size and two lengths are good and what I'm using here is kind of like a drop
angle grinder like a drop saw but it's for metal for steel and it looks pretty cool as it's going there
oh look at that pretty good so yeah just cut the second piece out now once the fire's going you
chuck it in there and let it heat up and so I'm not like I said this is not complex we're not
doing anything complex here is my dad kind of giving me a head start on it and so just heating
it up and banging it into a shape and uh actually it's banging banging an angle on it so there's a
little bit of fiddling well I found that there was a little bit of fiddling to get the the shape
um and when I say exactly right I did not get anything exactly right here but get the shape
at least passable for it to function the way I want it and so um it's a there's a it's a
first attempt and it looks like a handle and you look at it as very handle like but the
shape is very very um disproportioned it's not even on either side but uh oh you know
uh it's close enough and so yeah I just do a little bit more tinkering to get it a bit closer
to a possible shape to function for the handle of a shield now this is my second attempt I learned
a bit from the first and so I worked at uh making those uh sides more even um and also to make the
handle closer to where my fist would be on the shield look at that that is much more even than
my first attempt so I was a bit a bit happy with that happier than my first attempt anyway
now now you get to see the results this was my first attempt the first handle that we did
and you'll notice that it's uneven and also it's far too big so if I was look how far the handle
rests above my hand I actually need to raise my hand to grab a hold of it so that's not going to
work at all my second attempt worked out much much better um the handle portion of it is closer to
the shield I can wrap my fist around it nicely and so resting my hand right against the shield
I can slide it in and grab the handle and uh right where it needs to be so that works out
much much better and so you can see the kind of difference so my first attempt was a bit of a fail
but I salvaged that first attempt I decided I'm going to use that first attempt as the hook that's
going to hook over my forearm near there my elbow joint so with uh the the my first attempt being
the hook and my second being the handle now it's a matter of aligning it on the shield for where
I'm going to be fixing it to the shield so I want it to you know put out the center portion of the
shield and there's a bit of measurement to make sure it's in the right position so that back hook
there is actually the the what's left of my first attempt I put it on the forge to put a new shape
in it and um and then also cut off one end and so it's perfect for the back hook now
so once I pick the positions of where I'm gonna put the handle and hook I need to drill the holes
and of course first of all when you're using any type of power tool you want protection safety
goggles safety glasses and goggles and all that good stuff and so then it's a matter of lining up
where you want those holes and drilling them and so this is uh this is obviously it's a metal drill
I don't even know the proper name see how much of a noob I am I don't even know the names of the
tools I'm using but anyway so yeah lining up and uh and drilling the holes look at that looks pretty
good doesn't it well I'm I'm happy with that I'm easily impressed so once you have those holes
drilled and again you don't need to do this you could just um you know use wooden handles or leather
straps or whatever but I drill through the hole on my metal handle right into the wood so the holes
will line up perfectly and look at that the screws just slide in without a problem so I was very happy
with how this is all working now the next part I want the um I'm using nuts and bolts here and
of course nuts and bolts are not historically accurate again remember this is a historical
approximation it's not we don't want to make a historical replica okay um and so I'm you I you
would not use nuts and bolts if um a shield was thinner I could not do this with my viking shield
because the wood is far too thin and that means the screw heads would jut out on the on top and
so I'm using um nuts here nuts and bolts here because the wood is thick enough for me to uh
drill them a bit further into the wood and have them flush with the top so the top will be
completely smooth and so the way I go about doing this is literally just drilling out the top kind
of layer of the the the screw holes that I've already um screwed in there or drilled in there
and so the same diameter as the bolt head and so that is going to sit in there perfectly and
it's going to be flush with the shield top now you want it to be a tight fit you don't want um
there to be much slack on the ends and so because it's a nice tight fit just needed to hammer them
in a little bit to make them very flush with the top and I did actually want them sticking out like
half a mil from the top because when I tighten them when I tighten the um the nut onto this onto
the bolt um it's gonna pull that bolt into the wood a little bit to make it really tight and so
I left a little bit of slack on the on the face of the shield um so when I tighten it it'll go
perfectly flush and the the um the joint will be really tight now look at this look at that
that's exactly what I wanted I wanted a quick grab um so you don't need a you fiddle with straps or
anything just grab it straight on and then you're holding it and the way it's built this is the
advantage of heater shields any type of strap shield you have full articulation with the shield
you can rotate your wrist and the shield rotates perfectly and the whole thing is braced against
your arm and so you're able to take much bigger hits so that's what the um my handle and metal
hook looks like and uh and it works pretty good I'm quite happy with that now look just in and
grab it so that's why I picked this configuration for speed you just pick it up and you're good to
go something else that I was happy with and this is intentional is that there's enough room on the
handle to hold something else um specifically the reins of a horse um these shields are used
on horseback as much as anything else and say there you go now pay attention to where I actually
put the the handle and hook on the shield because you'll notice that I didn't center them perfectly
and that again is intentional because what you want to be centered is your forearm you want your
forearm and fist to be centered on the shield and so to do that you need to position the handle and
hook a bit off center to each other and so take a close look and you'll see the proportions of where
where I place this to make sure my forearm is centered when I'm holding it and so the hook is
placed further in from the side of the shield as opposed to the handle so this is all very
intentional and the reason why the hook needs to be further in is for your elbow that your elbow
joint forearm because you'll have some space and then you're going to hit where your elbow is and
so that's the beginning of your forearm or to get your arm to be fully centered on the back of the
now heater shields are thick shields they get most of their strength literally from the thickness of
the wood whereas older shields or sorry not older but thinner shields because you can have thinner
shields in this period as well they got their strength from having raw hide stretch over the
front now you can have raw hide over the front of the heater shield and I'm sure that was done
historically as well but it was also not done historically because like I said before you get
ample strength and protection just from the thickness of the wood and so if I was to try and
make an approximate historical proximate and I did this with my viking shield bear in mind
because my viking shield is much thinner is that to get the approximate you you slather glue over
the face of the shield and then you stretch material just normal material over on top of that
on top of that glue and so when that dries it hardens really really good and becomes really
tough and it becomes a decent enough approximation of rawhide and it gives a huge amount of strength
to thinner shields which they need that strength because my viking shield is only like two mil
thick and so even a blunt sword could go through that so yes they need the strength of rawhide
and the way you get a modern analog without needing to go to the trouble of using real rawhide
is glue and material but I'm not doing that with this shield I'm just showing you in case you want
to do that with any shields you make in the future I'm just happy with the thickness of
the shield as is and so my next step is of course sanding it and so I just get a nice belt sander
out and go over it several times and it makes it really nice and smooth and it even sands down
some of those bolts if they were protruding a little bit more and of course sand the edges
to make them smooth as well the next step is a completely optional step just like the having
actual steel handles that's completely optional as well because the the shield as you see it right
now could be you could consider it very well done all you need to do is paint it up and you're good
to go it's done all right but I'm a bit of a not well I say perfectionist I just you know I like
things to be uh good well that's surprising everyone likes things to be good but you know
what I'm saying and and so what I wanted to do I wanted a metal I want yeah metal rim around my
shield and I've done it with all my other shields and so I'm putting a metal rim around my heater
shield and it's not really you know for function though it would make it a little bit strong but
I'm using tin and tin is really really weak stuff I mean yes it's metal but it's not strong and so
that would add a little bit of strength to the shield it's not a huge amount what I'm really
doing it for is for looks because it looks awesome and so I'm just using some scrap tin here
and just literally tracing the edges of the shield for where I'm going to snip it now I use tin snips
to cut this stuff out and oh boy is that a workout on the wrists but yeah so you measure it and once
you have the measurements then you're good to cut now of course before you even get to putting on
this metal rim and and if you're not even going to be doing a metal rim because like I said it's
you need to paint it and painting is an essential part although it's not essential but
you really want to paint a shield it'll look kind of poxy well not very good without it being
painted and so I'm I just like the four-quartered checkered pattern and so I divide it into four
quarters measure it out with a ruler paint along the edges with a smaller brush so I can make that
line a bit sharper and so once I paint along with a smaller brush I go over it with a bigger brush
now I'm doing it in this order because for one I wanted to measure up the the borders of my shield
so I could cut the tin net you know the right way I need to do that before I painted it of course
or you could do it after you paint it I just didn't want to have to wait until it was dry
so I measured up before I paint but then I put the rim on after it's painted of course
because you don't want to paint over your metal rim or anything like that
yeah so you know once it's painted you cut those the rim that you've pre-measured
out of the your tin and so careful of sharp bits when doing this because the the off cuts
you're very very sharp they will poke you and draw blood very very easily so yes just be careful
of that and use gloves right use gloves and you're lucky that this is fast forwarded because
it's a bit of a timely process and you'll see me pausing now I'm shaking my hand because it's
getting so sore this is a workout on your hand grip my goodness there you go so that's the first
now you will have noticed that there is a line down each of the strips that I have cut
so that line is there to tell me that how much of this strip is going to be sitting on the shield
and how much is sitting off because that portion that is sitting off the shield well you'll see
what I'm going to do with it later on so I'm sure you're enjoying watching the you know sped up
of the you know the fast forwarding of this seeing me work away hard but so while you're
watching and uh there's a bit of a pause I am gonna go make a sandwich
oh yeah sorry just just uh chewing there but um oh we haven't even come to that so
I'll finish my sandwich hang on that was good ham yes tasty ah now I mentioned that as a workout
on the hands gee do you see that red there kind of it's flaring up already from all the pressure
that we're putting on the hand yeah ouchies certainly a workout next we're going to be
putting on a metal rim and so it's it's going to be uh uh holding to the shield in multiple
different ways glue primarily so you chuck the glue on and then you use some hand clamps to hold
it in place and so now you get to see what I'm going to do with that portion that's hanging off
so what I do I cut into the tin making little tags along the edge of the shield so you don't
cut any further into the part that's actually sitting on the shield you're only cutting the
part that's resting off the shield and so you make tags and then what you do you get some pliers
and you bend with the pliers and sometimes just with your hand as well you bend those tags down
and around the edge of the shield and so that will help hold the this metal rim to the shield
and then the glue will finish the job let's see there you go see how I've bent those tags
um down over the edge of the shield and then under all along there and uh you'll see that
it looks pretty good the finish result looks pretty darn good so then it's just a simple
matter of rinse and repeat you do that with all the other edges I love hand clamps hand clamps
are awesome you know you can never have too many hand clamps true it's a true thing I'm serious
hand clamps you never have too many you think I've used enough I think I might need some more
if I want to hold on those other metal rims I'll certainly need some more hand clamps
and of course what you're seeing me do here is the exact same thing before I'm cutting those
tags into the edge of the metal rim and then bending those tags over the edge of the shield
so in the process of me putting this metal rim around the shield I was not happy with
where the top corner was sitting and so I needed to redo it and that that was a bit fiddly you
don't want to have to redo it but you know you do what you need to do and I got it in a passable
position an acceptable position like I said none of this is perfect none of it is lining up
perfectly at all but I'm just making it to a passable standard that and that standard is my
standard where I'm happy with the quality or I can accept the quality that might be enough hand
clamps maybe maybe isn't with your rim on and the tags all bent around the sides so you have that
metal rim literally going along the entire border of your shield it's a matter of waiting for that
glue to dry and so you can come back later or whatnot but once it's dry you're free to take
off those clamps and there you have it then the the shield has a metal rim what you need to be
careful about when you're putting on this metal rim is the spiky pokey parts of the tin specifically
on the other side those tags that you cut in on the edges of the shield those can be very spiky
and so you need to do something to make the shield safe and so what I do is that I cover the edges of
the the rim in silicon and that silicon also acts as an additional glue holding the rim even like in
a very very firm way to the shield and silicon is great it has a very rubbery kind of texture
rubbery finish and so that covers all the spiky dangerous parts of the tin and metal
making the shield completely safe and it gives it its kind of final finishing touch
and so once you have that when you when you have the rim fully glued by glue and silicon
to the shield and all the spiky parts covered it's done there you go that's what it looks like that
is the heater shield with a metal rim all around with metal handles and again you don't need to do
the metal rim all the handles you can just do leather straps but gee it looks good well I think
it looks good I'm very happy with the final the end result there and I hope you have enjoyed
watching and I wish you all the best if you go forward in the future and endeavor to try and make
a shield and if you use any of the advice or have learned from the demonstrations that I've been
able to show here well that gratifies me greatly it's good to know that I've been able to help in
some small way and please do stick around because one of the very reasons why I'm making this shield
is to do videos on on shields as to how they were used how they evolved how did you how did the
round shield and why did the round shield evolve into the kite shield and why did the kite shield
evolve into the heater shield that you got to see me make here you will find videos on my channel
touching on those topics addressing each individual shield and you'll also get to see the shields that
I've made if you want to take a look at them so again thank you for watching and I hope you enjoyed
