
Ceramic Art Studio
35 followers
May 27, 2025
Hi everybody, this is Anne. When I think about fruit bowls, I picture a typical generic round
shape just bigger so it can hold a lot of fruit. But I recently saw a fruit bowl that didn't fit
the generic description at all as it was a very simple yet contemporary shape. I thought perhaps
I could challenge myself to think outside the box and make some unique hand-built fruit bowls.
For inspiration, I looked to actual fruit. I sketched out a template in the shape of a banana
peel. I rolled out a quarter inch slab of clay and ribbed it smooth with my rubber rib.
I cut out the template from the slab. I then rolled out a thin long coil for a border.
I placed the slab on a piece of plastic wrap. I wet the coil and attached it along the edge
around the entire slab. I used my fingers to seal the coil to the edge.
I covered the slab with plastic wrap and flipped it over. I then worked the clay at the seams to
seal the coil along that side of the slab. For a mold, I ripped off some tar paper from my tar
paper roll. It'll work well for my purposes as it's stiff yet flexible, durable, and waterproof,
but most importantly it'll hold the shape that I need. I placed the slab in the mold. I folded the
mold, then shaped the clay, rolling the edges together and shaping the clay just how I wanted.
To hold it in place as it dried and shrank, I taped the top of the tar paper in a tubular shape.
Then I let it dry slowly. Here it is in the bone dry state. I really like that organic shape.
I painted underglaze lines to accentuate the width of the piece and give it direction.
To finish it, I glazed the inside with amaco marigold glaze to mimic the banana and then
white around all the lines on the outside. Now it's ready for a line of fruits or berries.
Next, I thought I'd try to create a bowl based on the shape of a fruit slice.
I started with a quarter inch slab and traced out the fruit slice template.
I then rolled out an eighth of an inch slab and cut out the arch template.
I wet the surface of the slab and attached the arch strip along the curved edge of the slice.
I worked the inner edge downward with my finger so it was flush to the bottom slab.
I continued working it down with both my fingers and the red rubber rib
until it was smooth and the slab became a wedge slice.
I centered the last template piece along the front edge and traced
lightly the lines onto the slab to complete the design. I made five of these slices.
I laid a piece of plastic wrap down on the table and began stacking the slices,
staggering them as shown. When I was happy with the placement, I scored and slipped each slice
in place. For a mold, I'll be using the large styrofoam half sphere. I picked up the plastic
and placed the slices down in the bowl. I gently pushed the slices to conform to the round shape.
I let it dry slowly inside the mold and when it was a stiff leather hard, I carved away the
lines that I traced to accentuate that citrus feel. Here's one that I made earlier. I like
that almost braided looking pattern that the staggered slices creates. And on the back side,
there's a nice woven pattern too. It isn't a deep bowl, but it'll hold fruit and it'll make a nice
contemporary centerpiece to a table. To finish, I glazed it with transparent opulence lemon drop
glaze, which has a soft citrus color and breaks well over the texture. The color acts as an almost
neutral one so it'll work well to display many different varieties of fruit. Finally, I thought
I'd create a bowl inspired not by fruit, but by the pea pod. I rolled out a coil about three quarters
to one inch thick and eight inches long. I cut off the ends of the coil to get rid of the jagged edges.
I wanted to round the ends a little, so I pounced them flat and smooth first, then rolled the edges
on the table to start rounding them. As I rolled, I worked the jagged clay edges inward and smooth
until I had both edges the way that I wanted them. I then pounced one side of the coil on the table to
flatten it a bit. I wanted to hollow it out. I used a round carving tool and shallowly carved
down the center length of that flat side of the coil. I kept carving out shallow strips until I
with my fingers on the inside and the rim. I rolled a long skinny coil for the rim. I placed it
around the circumference of the rim and trimmed off the excess. I removed the coil from the bowl
and connected the ends well. I used a small carving tool to dig out a trench all the way around the top
of the coil so it'll fit over the rim easily. I worked the jagged edges down a bit. I wet the rim
of the bowl then worked the coil down over the rim and attached it well. To create the peapod shape, I
held my fingers where I wanted the rim to ripple inward then began to push the clay between my
fingers outward. I then worked more ripples to the clay outside of my fingers. I repeated this on the
other side so it was symmetrical. Here's one that I made earlier. The ripples resemble the part of
the peapod where the little peas would be nestled. To finish it, I glazed it with Amaco True Celadon
Glaze on the inside which is the perfect pea color. I added a pattern of lines to the outside with
underglaze and glazed it with my white liner glaze. It's perfect for small fruit, berries, or even nuts
or candy. I love that you really don't have to go far for inspiration to make pottery. You may just
have to open your refrigerator. Thanks to the newest members of our Little Street Pottery Research
Facility Team. If you'd like to join the team and earn a title, click on the Super Thanks button or
the link to buy me a coffee. It also really helps us out if you hit that like button and subscribe
to our channel. See you next time in the studio!
