Mount and Balance Tires at Home: Manual Tire Changer & Bubble Balancer

Car Tires TV
5 followers
146 Video Views·Apr 25, 2025
If you're wondering how to mount and balance tires at home, I'll be showing the process on 20" alloy wheels and fairly low profile tires (no wheel scratching allowed). I'll be using the ever popular manual tire changer with a duck head modification attachment and the infamous bubble balancer.
Howdy folks, John here. Welcome to the third and final video in my DIY manual tire changer series.
Today we'll get the new 235-45 R20 tires mounted onto the alloy wheels without a scratch.
We'll then see how well one of those low-cost bubble balancers is able to balance them up,
finishing off with a road test to feel for vibrations. Let's get it done.
So the new running shoes have arrived. Before mounting them onto the wheels, however,
got to check a few things on both the tire and the wheels. I like to clean the old tire residue
off the rims before mounting, just using a little plastic scraper here,
something that the tire shops will rarely, if ever, do. If your valve stems are fairly old,
might want to replace them. I'm going to replace all mine. Again, if there was any dirt in here,
I'd probably spend a little time cleaning that out. One thing to note, if you're match balancing,
there's a lot of misinformation out on the internet saying that the valve stem area is always
the heaviest part of the wheel. That's not the case. In fact, you're probably going to find it's
the lightest. If you've got TPMS sensors in here, that's what this cutout is here for, and that's
why this side of the wheel is actually probably going to be lighter than the rest, if you check
the balance just of the wheel alone. Here, for example, on this winter wheel set that I'm just
checking the balance of the wheel, the valve stem side is actually the lightest. I'm having
to actually press down slightly to center the bubble. Match balancing this tire, yellow dot
on the opposite side, which is the heaviest part of the wheel and lightest part of the tire, we've
got a perfect balance without any weights needed. Obviously, if you've got TPMS sensor valve stems,
yeah, this will be the heaviest part of the wheel, but if you're just using regular valve stems,
this part of the wheel is actually probably going to be the lightest.
If your valve stems don't come pre-lubed, putting on a little tire lube of your choice
to slide them in never hurts. To pull the valve stem through, I'm just going to use one of these
little valve stem tools. Put the valve stem in through the back, thread the tool on,
and pull it up. You'll hear it pop when it's in place. The last thing I'm going to do on
the wheel now is just remove the wheel weights. We're going to be rebalancing it when the new
tires are on. If you've got leaded wheel weights, you might want to hang on to them
and just reapply some three-sided double-sided tape. It's getting hard to find lead weights like
these. Again, I'll just take a little extra time cleaning the residue where those wheel weights
were with some brake clean. Just get all the gum off of there. The next thing you have to
check is actually on the tire itself. If you've got directional tires, you're going to want to
which wheels are on the left and right side of your vehicle so you know which way they turn and
if there's an inner and an outer. These are non-directional tires, but they certainly have
an inner side and an outer side. It'll say somewhere on the tire, inside or outside.
Here we've got inner, so this side has got to be facing the back of the wheel.
We're going to slide over first and on the other side here, it says outer. Before mounting the
tire, we've got to lube it up. I like using a paste lube for mounting and a liquid lube as
we saw during the dismounting video. This is just so there's no liquid that's going to be trapped
in the tire after it's mounted. These cheap ebay brushes, by the way, are garbage. The little hairs
shed on them and if you get a hair between the bead and the wheel seat or the rim,
it could slowly leak air. So I should have just used a good old paintbrush.
Of course, do both sides. Mounting the tire to the wheel is a lot easier than dismounting. You
don't have to use a tire bar or anything. If you are going to match balance the tire to the wheel,
we don't have to worry with these because they don't have the little yellow dot on them that
signifies the light spot. But if you were and you wanted to go to that trouble, you would first
check the wheel balance without the tire on. Find the heaviest spot on the wheel, put a little mark
on it or something and then match that little yellow dot up. We don't have to worry about that
with this. Again, make sure you know which is inner and outer. So you're putting the inner side on
first and if you've got directional wheels just make sure you've got the left tires on the left
wheel right on the right. So to get these on we don't really need anything special. It should
just slide on without too much force like so. Now getting the top bead seated is a little more
difficult. I find that help are one of these little tools that hold the tire down in the wheel dish.
We're going to get our duck head out. I like lubing the duck head so it slides nice and easy around
the rim. You don't want any dirt on the rim of course because it could scratch.
Same with dirt on the duck head. Now just fit that in there, tighten it up.
If you remember before when we took the tire off we were pulling the bead over the top of the duck
beak or head and this side was riding underneath. The bead was riding underneath this side. We want
the bead over top of there and underneath the duck head like that. Just make sure you don't get
your fingers trapped in here. I've got to get the bar in here because it does take a little bit of
force and you just want to make sure that you're holding that bead underneath that duck beak or
duck head as you go around. That's it. Easy breezy. You'll find this process is even easier
with higher profile tires. Here these winter 235 55 18s and I don't even need the little bead clamp
at all. Just going around don't even need the bar. They pop on really easy.
I'll just take the duck head adapter off here. It's like going around with a damp
rag at this point. Just inspect the wheel make sure there's no scratches.
Looks absolutely pristine. Now we get to do the most fun thing and dangerous,
seeding the beads. Get your eye protectors out. You're probably going to need an air compressor
for this because you have to force a bit of air in there pretty quickly. I like using these digital
gauges. They work really well. So, seeding the bead. Tires will have a maximum bead seeding
pressure. They're usually around 40 psi. Double check these and these are 40 so you don't want
to go over 40. As long as you've got lubrication on there you shouldn't even come close to that
but we'll see where this ends up. Seeding. Back usually seats first. You hear it pop.
15 almost. I'm actually going to I'm going to move the camera. I don't like being over this
section here. There was the back side that went. I just don't like that. I guess I can hold it this
way. That's still in frame now. I don't know if we can see that though. Ah come on. What are we at?
19 psi. As you can see that back one popped in really quick. Oh any minute now. Any minute.
Wait for it. There she goes. 27 is where it popped in. Now you just want to fill your tires up to
whatever psi you want. I'm going to set this at 36. Close enough. Another little thing I like doing
whether I'm installing tires myself or at a shop is to get brand new tire depth.
What do we got there? Come on focus. 11 30 seconds and I'll write that in the maintenance
log for the car. With the four new tires mounted on the wheels it's time to balance them. Like most
DIY home gamers I'm going to be using one of these low cost bubble balancers. Now these things are a
complete crap shoot and out of the box mine was at the far end of that crap scale. It had the two
most common problems you often read about. I'm going to quickly show you how I address them.
I don't want to spend too much time on this. You can read reviews and forum posts about the
problems with these bubble balancers. It all stems from the way they pivot. The pivot point itself
and the thing up in the head here that the little hardened steel thing pivots on. First problem is
this is quite wide in relationship to this hole so it's actually not pivoting on the tip. It's
pivoting on the shoulder of that pin so you get very poor resolution. It sticks. People grind
these down to a sharp point so it will actually fit in the hole but then you have a problem of it
actually putting a divot inside here and it gets just as tight to move and it can even go off
center and that's the other problem with these things. Rarely is the pivot point in the head
centered in relationship to the cone where the wheel sits and of course if the wheel isn't
sitting perfectly centered on the pivot point it's going to be heavy on one side all the time
so you're never going to be able to balance it. I've solved both issues by using a glass plate.
This is actually a Hardex glass crystal and a half sphere magnifier. I wanted to use glass,
very smooth so it's got very little resistance. So this is up inside the head and it pivots on
this little glass plate. There's other ways to do it and I just 3d printed this little plate
adapter but you can make it out of anything and it just slides on there and then the glass crystal
I've got glued inside that's showing up and centered it. It was a complicated process. I just
used my lathe with the drill stock dial indicator just to make sure that crystal was perfectly
centered in relationship to the wheel and now the bubble is completely is always centered no
matter where you turn this in relationship to the balancer. Before the bubble was always lopsided
that's one way you can tell it's off-center and as far as pivot movement how easy it is to pivot
and you know resolution before just with the pin it would maybe tilt back and forth
three or four times you know a few seconds before it would stop if you gave it a shake.
Now with the glass crystal in there you can give it a shake and it'll be still moving two minutes
later with the wheel on it still moves 10 minutes later so very low resistance. The only problem
with it of course is it's fragile so you got to be really careful when you put the wheel on. I'm
going to do this freehand so we can get right over top of the bubble nice and square but as you can
see just gave it a little shake just it will it won't stop for a couple of minutes that's how
little resistance there is and to set these up just stop it from moving you want that little
bubble perfectly centered you can use these little three screws to center it once you center it
shouldn't really be out anymore come on focus and like I said if you turn this now that bubble should
remain perfectly centered no matter where it's sitting showing you that the pivot point is
perfectly centered so let's get a wheel on like I said you got to be pretty uh gentle because it is
that glass crystal in there but even if it was the pin you'd still have to be gentle so you don't put
a big divot in there well I guess we should take the sticker off I want that so yeah like I said
you give this thing a shake come back 10 minutes it'll still be moving but anyway let's uh just
get that stopped and we'll take a look where the bubble is I don't know how good this is going to
show up it's pretty centered I'd probably be okay with this but it's just a little bit the bubble
sitting a little bit this way meaning this side is a little light so I'm just going to put a little
15 gram weight basically in line here while we look at the bubble put it roughly where the inside
of the rim is and I don't know if you saw that bubble move but it did move a little closer to
center so that's where I'm going to put that weight just going to mark it on the inside you
know and that's the other problem with these bubble balances is you are just doing a static balance
and the wider the wheel is the more important the dynamic balance is because the further the weight
it's going to give you a more of a vibration on a wide wheel than it would a really skinny
skinny one so is this a substitute for computerized dynamic balancing not at all
I'm just hoping it gets me close enough so my fillings aren't being rattled out as I drive
300 kilometers to the city to get these properly balanced but if this works well I may not have to
so there's our little mark I'm just going to clean the wheel where I'm going to stick the
wheel weight because this is just a static balance I kind of want the wheel weight in line with the
with the face plate of the wheel here so I'm going to put it here you know most of the mass
of the wheel is obviously on the spoke side here but just gonna go kind of in line with that
mounting plate of the wheel so now we'll put it back on the balancer and see how it does
there's our wheel weight and we'll come back to the little bubble here
perfectly centered and rotated 180 degrees so the wheel weight is on this side just to make
sure it hasn't changed rotated the wheel 180 degrees on the cone to where it was
and hopefully the camera's picking that up but the bubble is still perfectly centered
if we want we could even just spin the wheel and if your pivot point is perfectly centered
no matter where you spin the wheel that bubble should remain perfectly centered so I'm pretty
happy with the static balance ability of this little bubble balancer with the modifications
certainly wouldn't recommend one of these things to anyone if you don't want to do them
they don't work well unless you put a little time into them in my opinion but we'll see how it goes
when the rubber really does meet the road we'll go for a road test right away
but knowing how well the manual tire changer works with the duckhead adapter
you know kind of contemplating whether it'd be worth buying a computerized balancing machine
you were either looking for a used one the mayflower down in the states you can pick
those up for around a thousand dollars for a DIYer at home a fair chunk of change but
if you did enough it might pay for itself it's just the convenience main thing I wanted to see
if the bubble balancer if it even works and again so the trip up to the city isn't too
uncomfortable to take it to a shop and get it properly done on a computerized balancer
but who knows might be okay we'll see it on the highway okay to check uh balance on wheels and
tires obviously like to find a nice smooth stretch of highway wheel balance problems
generally don't start showing up until about 80 kilometers an hour 50 miles an hour we're at 90
right now
