How To Mount and Balance Tires Without A Tire Machine. ( Change Tires At Home - DIY )

Car Tires TV
5 followers
23 Video Views·Sep 1, 2025
In this video I'm going to show you how to mount and balance tires without a tire machine. This procedure works great for tires with taller sidewalls. Tires with extremely low profile sidewalls or extremely stiff sidewalls will be a struggle to mount using this procedure. What I'm showing in this video is how tires were mounted and balanced back in the 1940s and 1950s.
So today I'm going to show you guys how to change out your own tires at home
without a tire machine. Now to get this done I'm going to be doing this the old school way
with two tire spoons. This is how they used to change out tires back in the day back in like
the 40s and 50s. This is how they did it. You can buy these for about roughly 20 to 30 dollars a
piece. You're going to need two of those. In addition to that you're also going to need
some sort of balancer. Now I'm going to use a bubble balancer to get this done.
In addition to the tire spoons and the bubble balancer you will need an air compressor with
a tank on it to be able to pop the beads back on when you get these tires changed out. In addition
to those things that you will absolutely need to get this done there's a couple optional things
you may want to consider. First thing is the valve core tool. You can get it done without a valve
core tool but again it's kind of recommended to remove the valve cores. It's a heck of a lot
easier to get it taken out with the correct tool and as you would expect these are super cheap.
Now the second optional tool is going to be a valve stem tool. So this actually threads onto
the valve stem and then you use this to pry out the old valve stem and to pop the new one into
the rim. Now with that said what I'm about to show you in this video guys will not work for
all of the tires out on the market and the other thing is if you care about these wheels
I'm not going to recommend you attempt what I'm going to show you in this video.
So let me elaborate a little bit. All right so moving over to the other section of my garage
before we dive into this video I'm going to show you all the vehicles that I would not do this
procedure to. So taking a look here I've got three different vehicles in here and I'm going to be
honest every one of these I would not attempt to do what I'm going to show you in this video.
I wouldn't attempt to do this procedure to any one of these three. The primary reason is I actually
care about the wheels on these vehicles. So if you care about the wheels at all this probably
isn't a good idea to attempt what I'm showing you in this video. Just take it to the tire shop
and let them deal with it. The second reason is is like my Mustang for example this has 285
35 18 tires on it. The sidewalls are fairly low profile. Well the lower the profile of the tire
the harder it's going to be to get this done. So even on this Escape this one's also fairly low
profile. Again it's probably going to be tough to get those beads broken and get this tire broken
down manually. Just take these two to a tire shop and let them deal with it. It's not going to be
worth your aggravation to try and do this. Now in the case of my truck yes I could probably do
this procedure to my truck but there's a fundamental problem here. I actually care about
what these wheels look like so therefore I'm going to pay the $200 to have it mounted and balanced
locally. My wife actually just had new tires put on this Escape about a couple thousand miles ago
and that is what it cost me to have that done. So what I'm showing you in this video guys you can
buy all the tools to do this yourself for cheaper than what I can have a set of four wheels and
mounted and balanced locally. So keep that in mind as you're watching what I'm doing in this
video. If you have a cheap beater car that you don't care about the wheels or you have a set of
steel wheels that you can touch up with just some black spray paint that is the perfect candidate
to do this procedure to. All right so the first thing we need to do here to get this tire off the
rim is we need to break the bead of the tire on both sides. Now what you're going to have to do
here is first of all you need to remove the valve core out of the wheel. I'm using a valve core tool
when you take the valve core out you're going to have a bunch of air escape out of the tire.
This tire has a hole in it so naturally there's no air in it but at this point the next thing you
need to do is get your vehicle jacked up or use like a trailer or something. What you're trying
to do here ultimately is you're trying to get something to push down on the sidewall of the tire
in order to push the tire down and the rim is essentially going to stay in place so that is
going to break the bead on the tire. When you break the bead this tire has a TPMS sensor in it.
When you break the bead you want to make sure that you break the bead on the opposite side of the
tire as where the TPMS sensor is. If you break the bead where the TPMS sensor is you will break it.
So what you're going to do is you're going to take like a scissor jack,
you can use a trailer, whatever you have at your disposal and essentially what you're going to do
here is you're going to push down on the sidewall of the tire and what that's going to do is that's
going to push the tire off the rim. So now I can sit here and crank this bolt and I'm holding
the opposite end of the tire here with my knee so there now at that point you see I can just push
down on that and now that bead's broken all the way around. So now we got to flip the rim over
and do the same thing on the other side. This is why I said up front if you care about these wheels
at all just take it to a tire shop and let them do it because like right now this wheel is resting
on the face on the concrete. If it gets scratched really not the end of the world. These things have
been hit up been hit off of curbs and stuff already. They have a little bit of curb rash on
them so you know what a couple more scratches really isn't the end of the world. But now
I'm going to do the exact same thing to the other side. So you're going to sit here and push down
on this thing and if you got to go around in a couple spots to do this you may have to do that.
So I'm going to let the tension off the jack. I'm going to turn the wheel and hit this thing again
in another spot. There you go. So now I should be able to just push on that wheel
and there you can see the bead's broken now on both sides. So now
pull the jack out of here and we're going to start working on getting this tire off.
Now the key to being able to remove these tires yourself is going to be something called the drop
center of the wheel. For those of you that don't know what the drop center of the wheel is,
this narrow section that you see on the wheel in the barrel that is what is called the drop center.
So what I'm doing as I'm going to remove this wheel is I am pushing the sidewall of the tire
down into this drop center of the wheel. When the tire goes down into the drop center of the wheel
that is going to allow me to pry on the opposite side of the tire and pry it up and off of the
wheel. This is the key to getting this whole thing done. If you don't know what the drop center is or
how to use it you will never get this done. So this is why I'm putting it right up front.
You have to understand if you push the tire down into the drop center that is what allows you to
pry it up and off of the rim. So right here is my valve stem. This is where I want to start.
What you're going to do is you're going to get your two spoons and I like using the hook end.
So you're going to come in here like this and you're going to grab this tire and as you're
grabbing this tire you're going to stand on the opposite side of the tire to push this side down
into that drop center. So when this side goes into the drop center that's going to allow this end of
the tire to come up and over the rim. So if you look you see I've got that end up over the rim.
So now what I'm going to do get my other pry bar in here. So now basically you're just going to
work that off with one pry bar at a time. So now I'll come over here take a bite do the same thing
grab another bite over here and do the same thing. If you look
that tire is loose now. So now the back side is a little bit harder. Now at this point I would go
through and remove the TPMS sensor if the wheel you're dealing with is equipped with one. If you
remove it it's just much less likely to be broken if you remove it at this point. So now at this
point you're going to be left with something like this where the rim is still in the tire
but it's loose. You have to get it past this second bead. The way that I found to get this
thing out of here it's going to be dependent on how stiff the sidewalls of your tires are.
Obviously the stiffer the sidewall the harder it is that it's going to be to change out these tires
but what I ultimately found is if I took one of these spoons and I shoved it in here something
like this and I was able to get this spoon kind of on the face you can see it right here.
So it's through there like that then what I do is I'll lay the rim on the ground
and I'll stand on it and just simply pull on the spoon.
When I do this you'll see if I get you in here close in a second you just start pulling on this
thing and it'll eventually pop out of there. When I'm prying on this thing I have the spoon
is down in the barrel. I'm not prying on this face I'm prying inside the rim.
Something like that. Just give it a little yank and it'll come up on off of there. To me
if you could get the tire off the rim that is much harder than putting the tire on the rim.
So now that the tire is removed I just want to show you guys exactly what I was doing in that
last step. So I took the spoon and I got it between the tire and the rim right in this area
and I stuck the spoon through pretty far and then I started rolling it up the rim
and I eventually got it to about this point and if you look here I'm actually
I'm prying on the barrel portion of the rim. I'm not prying on the face of the rim at all because
I have these giant openings where these spokes are on this wheel. So this is the way that I've
seen to get this done is just come in here like this and just give it one of these and pull and
then it should just lift up and off of there fairly easily at that point. But to me that was
the absolute hardest part of getting these tires changed out was simply trying to figure out the
best way to get that second bead off of the rim. So now while I'm here I'm going to change out the
valve stems because well why not I'm in here this far so I might as well change out the valve stem
these should just pull up and out if you pull hard enough you'll break it but there's the other half
but if you get new valve stems they tend to seal up a little bit better than reusing the old ones
just something to keep in mind if you're going into it this far doing it yourself. Now this next
step is going to be optional as well and what I'm doing here is I'm actually just cleaning the the
bead area that the tire seats against to ensure that I don't have any bead leaks. To do this I'm
just using a red scotch brite and just kind of scuffing the the bead area with a scotch brite
trying to get all the old sealants off of there any old tire residue off of there just make sure
that this new tire has a nice smooth area to seat against. While you're in here you're also going to
want to remove any old wheel weights get all the old wheel weights off the the wheel because we're
going to rebalance this with the new tire. So once you have the rim all cleaned up go ahead and take
your new valve stem if you're going to install one put a little bit of soap or lubricant or
whatever you're going to use on it and that's going to get pushed through from the back side.
So I'm going to use a valve stem tool to do this honestly if you just push on it maybe with a
socket or something you could probably get it popped through without buying the tool but I
have the tool so I'm going to use it. There you go so that's popped through I'm going to wait to
put the TPMS sensor on the stem until we get the tire partially mounted. All right so the next
thing you want to do is bring over your new tire and there's a couple things you want to note about
your new tire. Take a look at the sidewall and you see how that says outside that needs to face the
outside of the vehicle. If you mount it backwards you could end up with vibration problems just
something to take note of. Some tires are directional like these so make sure you're
mounting them the correct way. The other thing you want to take note of is this dot on the tire you
see that orange dot what that orange dot is for this that orange dot needs to align with the valve
stem on the rim. When you align the orange dot with the valve stem typically the tires balance
out a little bit easier. Now before I mount the tire into the rim or the rim end of the tire
depending on how you want to look at it I'm using some gojo hand soap because I have a bunch of it
around to lubricate the tire bead just to help that rim slide in. I've seen people use glass cleaner
you know hand soap naturally like I'm using. Use whatever you want here but use some sort of
lubricant to help these two things slide together easier. So right now I have what's considered the
outside of the tire facing the concrete so when I put this wheel in here naturally the wheel is also
going to face the concrete the face of the wheel I should say. So now sometimes you can just push
this through there honestly it doesn't always work out that way. Kind of like how you got it off
what I'm going to do is I'm going to grab this thing so there you go kind of like you uh like
it was when you were taking it apart you're just going to work that edge and basically pop that
thing in there. So now at this point I'll put the TPMS sensor in there since it's very unlikely I'll
damage it at this point. So now I'm getting my old TPMS sensors secured to my new valve stems
before I put this second bead on. So now that I have one side of the tire mounted now I need to
do the other. To do this you see I've got it all soaked up here but the other thing is I've got my
dot lined up with my valve stem at this point you can still slide this tire all over the place so
get it lined up and the way that I do this is I put the the valve stem at the 12 o'clock position
and I start working from the six o'clock position to the 12 o'clock position on the tire. So what
I'm going to do here is I'm going to take the tire and I'm going to push it down in the drop
center again and what I'm going to do is I'm actually going to stand on the tire and use my
feet to hold this tire where it needs to be. When I'm prying on the tire I am using the flat
the flatter side of the spoon. If you look the other end kind of has a hook on it like that and
that hook is a lot harder to pull out from the rim than what this flat side is so I try to use
the flat side when I'm doing this lessens the likelihood that you're going to do any damage to
the tire. So I'm standing on it like this and if you look there I can actually get this thing
mounted to about the nine and the three o'clock position. So what I'm going to do now make sure
your dot is still lined up and you're going to come in here at nine o'clock pry up when you do
that you're going to move your foot forward so now I can pull the pry bar out my foot's going to hold
that in place and I'm going to do that over here at three o'clock the exact same thing.
So now you look and I've got it to about ten o'clock and about two o'clock
and I'm just going to keep working that edge and moving my feet forward
until this thing pops back on. So now I'll leave the pry bar in there because it's going to start
at this point is when it starts to get hard to mount and hard to pry so if I come in here like
this and I try to go in at 12 o'clock and pry that there's no way you have to work along this
edge here where it's just starting to get mounted so I'm going to come in like right here and pop
that on. It'll be hard sometimes to get the pry tool in here you kind of have to lift up on the
tire to get the spoon in there and then again move your foot forward there you go mounted.
Now ordinarily you can just take some compressed air and air up the tire and that will naturally
pop the two beads back on without too much of an issue but unfortunately for me well it didn't
really work out that easily so if you're struggling to get the bead seated let me show you how I did
it. Now if you guys are having problems getting the bead seated this is what I found that worked
for me. These particular tires that I'm dealing with it seems like first of all the sidewalls
are kind of like pointed in like this so getting them to pop out against the the rim is kind of a
pain in the butt and the easiest way that I found to fix this is prop the tire up against an old one
put your foot inside the wheel and you're going to pull and you want to pull on the tire as hard
as you can because what this is going to do you're going to try and get this inner bead
seated without any air that way the air when you're trying to air it up only has one place to
escape and that would be out the other bead with this bead not seated and the other bead not seated
it's going out both places so it's much more likely to pop the bead on if you can get this
one at least somewhat started so I'm flipping this thing around and pulling and I'm kind of
walking this bead on just like you took it took it off of the pry bars so right like right in this
area where the bead isn't seated that's exactly where I'm going to start pulling so hopefully
that'll be enough like you see the giant gap that I have in there that's why these things are such
kind of a pain to pop onto the rims but with that bead partially seated now we can put some pressure
on this side and hopefully get this thing started now I understand there's a bunch of tutorials out
online telling you to wrap a ratchet strap around the tread of the tire and tighten down the ratchet
strap and that will cause the beads to seat I'm here to tell you I tried that for about 40 minutes
and I couldn't get it to work using this method that I just showed you I had it done in about five
your other alternative is a visit from the ether bunny but being that this is a how-to video and
you know that probably isn't the safest thing in the world well a visit from him isn't necessarily
something that I wanted to do with that rear bead seated I was able to tilt the tire up against an
old one like this and then just kind of put some pressure on the face as I was airing it up and
that eventually got the beads to start for me once they start it's just a matter of airing
up the tire until they pop on there it's starting to go there's the bottom there she goes yep about
27 so now we'll air it up to what it should be so now we're going to move on to balancing the
wheel and tire assembly and really you have two options for an at-home balance job you can use
a bubble balancer and do a static balance or you could use something called tire beads tire beads
actually go inside the tire and if you put the correct amount of beads in the tire as the tire
spins those beads sling out against the tread and those beads will actually help balance the tire
as you drive because the wheel and tire that I'm dealing with is fairly small a bubble balance will
work perfectly fine I understand a bubble balancer isn't even remotely in the same league as a
computerized wheel balancer that you would see at a tire shop but the reality of the situation is
you can buy one of these for less than $60 a good tire machine at a tire shop that'll do a
road force balance is probably going to set you back about $10,000 so my thing is I trust a guy
using a $50 balancer that cares about what he's doing more than I trust a guy that doesn't care
what he's doing using a $10,000 machine so again just like anything else when it comes to automotive
repair if you care about what you're doing generally you'll get good results so this is
what I'm going to be using for these tires in this video I'll have links in the description
to the bubble balancer and to the tire beads if you guys are doing large oversized tires
so with that let me dive in and show you how I'm going to get these things balanced
so if you're going to use a bubble balancer the first thing you need to do is come over to the top
of it and you'll see in there there's a little bubble level in there and if you move this thing
around you'll see that bubble will move all over the place now the first thing you need to do is
leave this thing stationary and let it settle out and then make sure your bubble is in the center
like it's supposed to be if it's not you're going to adjust the three screws that you see around the
bubble or around the level I should say and you're going to adjust those three screws to get the
bubble in the middle of the level so once you have the balancer sort of calibrated if you will go
ahead and take your tire and remove the center cap if you haven't already and all you're going to
do is you're going to set this thing down on the balancer like so and just give it a wiggle
and give it about two or three minutes for it to stop you know wiggling around eventually it'll
settle out and find level and stop moving and at that point is when you want to look at the bubble
in the top of the level to figure out where you actually need to add weights on the rim
all right so once this thing has settled out the first thing you want to evaluate is obviously the
position of the bubble in the level and the closer the bubble is to the line that is going to tell
you where you need to add weight so like right now the bubble is closest to the line in this
side with the valve stem so over here is where I need to add weight to this wheel now when you add
weight to the wheel actually take two weights and just set them on the face like this and when you
have two weights that are across from one another those weights will cancel out what you're going
to do is you're going to gradually slide these weights closer to one another and let this thing
settle and just evaluate the position of that bubble as you bring these weights closer and
closer together that is going to add more and more weight to this half of the wheel the thing
is if you just take like a half ounce of weight and stick it on here yeah it'll sort of get you
in the ballpark but this doing using two weights like this is going to save you a ton of like trial
and error and just simply slide these things and then let that bubble settle out so I'm going to
let this settle here for a second and we'll see what we get the other thing you have to be aware
of is the weights themselves are going to go on the inside of the rim right here right well when
you take the weights from the face and move them to the inside of the wheel that will actually
change how much effect that they have on the bubble itself so you may want to take some tape
and just hang the weights off of the wheel into the barrel with some tape to try and get a more
accurate reading if you so wish I can tell you guys the more that I've done this the better I've
gotten at it so just by looking at the bubble the relation of the bubble and the line you can kind
of tell how much weight you're going to have to add to the wheel so I'm going to let that settle
out here for a second and I'm probably going to stick these two weights down in that barrel there
so taking a look at the two images I have here on the screen the image on the left is before I
balance this tire and the image on the right is after so if you take a look at the image on the
left you'll notice the area from about 12 o'clock to about 10 o'clock that bubble is actually
slightly closer to that portion of the circle than what it is on the right so what you need
to do is wherever that bubble is closest to the line that is where you need to add weight so for
me to balance out this wheel I simply took two half ounce weights started out at nine o'clock
and three o'clock and eventually just slid them closer and closer to that area that the bubble is
closest to so when you do this correctly it should look like the bubble on the right and I'm happy to
say after I got this done I took this car out on the highway 80 miles an hour I can take my hands
off the steering wheel it tracks nice and straight there's no vibration at all so once you have that
bubble in the middle well the only thing that's left to do is take the tire off of it put your
center cap back in and you can mount this thing to the back up to the car take it for a test drive
so guys I was able to put about 300 miles on this Chevy Cruze before I got this video put out and I
am happy to say that I have had absolutely zero issues at all with these tires you know due to
my mounting and balancing and stuff I understand there's probably going to be a bunch of people in
the comments that work at tire shops and are going to tell me how much better a dynamic balance is
than you know a $50 bubble balancer but the reality of the situation is if you're dealing
with a reasonable size set of wheels and tires a bubble balance frankly is perfectly fine as long
as you care about what you're actually doing here so guys I will have links in the description
to the tire spoons to the bubble balancer and then to the valve core tool and as well as the
valve stem tool if you guys need any of that stuff as always guys if you guys like the video
hit like if you want to see more content go down and hit subscribe thanks for watching guys
