It seems rare that I have the chance to forge something for my own use. But the blacksmith shop needs a new door and the door needs hinges. That makes fora great opportunity to forge a set of strap hinges that are fancier than most of the hinges I have made in the past. I am also making the door, but that will be a separate video.
Blacksmithing and related activities can be hazardous. These videos are not a substitute for competent professional instruction. Your safety is your sole responsibility. Always use appropriate safety equipment including eye and ear protection when working in the shop. Follow manufactures safety guidelines for the use of all equipment. In the event something shown in one of these videos seems unsafe, it is up to you to make the appropriate changes to protect yourself.
This opening desperately needs a new door and a door needs hinges. So today let's take a look
at making some fancy strap hinges for the shop door. Any project starts with material selection
and since this is something I am making for my own shop I don't have a specific design
and no exact material requirements for this. I'm just going to use what's available on the rack.
It may not be exactly what I saw in my head but it will do just fine. It just means I have to
be a little bit more creative with the design if it's not exactly what I might have chosen
if it had been available. I probably would have gone with inch and a half and two inch material
if I'd had it. These hinges start by drawing them out to a taper. This is quick and efficient to do
under the power hammer. This is my preferred method for doing things like this. But as always
you don't have to have a power hammer in your shop if you're doing this kind of thing. You'll
feel restricted by the tools that someone else is using in their shop. Use the tools, the techniques,
and the skills that you have and just adapt to make that work for you. But if you don't have
a power hammer it can certainly be done over the horn of the anvil. This is pretty quick and
efficient as well. Not quite as much as using a power hammer but it can still be done without too
much trouble. I do want to knock the corners off the edge. I don't like sharp corners on things
like this. I also don't like to leave a factory edge that comes right from the steel mill.
But in this case that's not a problem since it's been tapered. I do want to take the wide strap down
to the same width as the narrow strap is for most of the hinge. But for the part up next to where
the hinge joint, the knuckle, is going to be I'm going to put a little bit of scroll work in there.
So I'm going to do an offset and this is just half face blows over the edge of the anvil.
And I'll take it down so that the strap portion is the same as the other hinge strap.
The most important part of a hinge is the pivot point, the knuckle, whatever you want to call it.
And I'm going to go ahead and show the entire thing on this one strap so you get an idea of
what I'm going through. Now this is taking longer than it might in some cases just because I haven't
made a hinge in a while. Certainly if you're making hinges out of thinner material this goes a lot
faster. But I also find that if I've been making hinges regularly for the last few months I can do
this in about a third of the time is what you're going to see here. And I don't rely quite so much
on this special swedge I've got. This is just a shop made tool. It's essentially a scroll starter
but I made it specifically for doing quarter inch thick hinges with a three-eighths hinge eye.
So it's sized just for this material and I was doing quite a few hinges in this size range at
one point in time. It is a bit of a crutch and it's not something you need. You don't have to
anything like this. But it is handy and it helps get the end of the eye tucked in nice and cleanly.
Lots of back and forth paying attention to both sides of the eye. It's easy to roll these up a
little bit conical if you're not paying attention to what you're doing. And you really need it to
be a parallel eye. Now the pins I use for sizing the eyes are made out of S7 tool steel. It's a
really good steel for this. I buy drill stock that is exactly the size I want it. In this case
this is three-eighths diameter and by doing it hot it's going to shrink a little bit so be slightly
under three-eighths diameter. And I'll discuss that before the end of the video and how I deal
with the fact that it's going to shrink up on me. These pins have a long taper on the side that goes
in the eye first and a short taper on the other end. So in most cases you can just drive it all
the way through without having to flip it back over again. Doing this last little bit of tightening
to get the eye good and closed up with the pin in it really makes for a more reliable approach.
Try not to hammer too much in the same spot or you'll end up with flat spots on there.
That can be hard to do because it seems like one spot is always where you want to be hammering.
Looks like I forgot to turn the microphone on for this short segment of video. So pardon me if we
don't have any shop sounds but we'll get through this pretty quickly and get back to making some
noise at the end. Far end of all these is going to be split into four little arms that have four
scrolls. This design is inspired by the New Mexican scroll hook that we took a look at last
year at some point. It was a design I had seen in Taos, New Mexico and I really liked it. I thought
it would be good for hinges so I'm doing something similar. It's not going to be exactly the same.
That one is split into six ends and this one is only being split into four ends. I think the other
one would just be a little bit too much and be overkill for the door that I'm putting in.
This needs to be opened up and then the rag from the chisel needs to be cleaned up. You can do this
with a hot rasp. File it cold. A belt grinder with a slack belt works pretty good for this. Just
whatever tools you have to have available for you to use in your shop. And of course the final
cleanup is still best done with a file. Files are really important tools for this kind of work.
Now we're on to one of the more tedious parts of the hinge and that's trying to get all of
these little fingers drawn out so they're all the same thickness, all the same taper,
and all the same length. Some of them are going to need to be trimmed before I'm all done.
It's just a matter of taking your time doing one after the other. It's kind of nice working over
the tail of the anvil or over the square horn in this case so that you can drop your hand down
further and have a wider range of motion on your hand holding the material. The bridge tool really
helps so you can get in between the fingers and it allows you to draw things out without having to
bend them around quite as much as you do otherwise. I think this might be made out of a section of old
road grader blade. Not exactly sure. It's something I made 20 or 30 years ago and I don't remember
exactly what I used for it but it works pretty well. Using a fat hot cut will give me a nice
angle for the spread on these and then I'll start scrolling these up. Again this is kind of tedious.
I don't think I'm going to show the entire process. One heat looks about the same as the other. I have
no idea how many heats I took to actually do this. Probably a dozen or more. These cool off
really fast. You got to keep going back to the fire. Though with persistence it can be done.
It's a little pair of scrolling pliers. I think blacksmith depot sells those if you're looking
for something like that. I don't have any kind of an affiliate link or sponsorship or anything like
that but if you're looking for a pair that's the place I'd look first. And of course the little
scroll forks that we made a few videos back really help with this. I've found lots of uses for these
section on the long straps I split similarly. I think I actually did these on the bandsaw so it's
all pretty much the same procedure. The bandsaw did leave a cleaner cut so I didn't need to go
grind these like I did the other ones. And in a lot of ways I think I like that better.
The chisel cut does leave a little bit of a bevel that can look good but these are coming
out cleaner and I don't have to fiddle around with them quite so much so I kind of like this process.
This entire project, the door, the hinges, represents a bit of a shift for me going into
the new year. This is the first video of 2025 I believe. And one of the things I want to try to
accomplish this year is more of the projects that I see in my life or in our life for my wife and I.
We have things in the house I've been meaning to do for five, six, seven years and just haven't
gotten around to because my priority has always been customer projects and videos just for the
of getting videos out. And I'm going to try and shift into making those projects
that I really want to get done and things that we need in our house. And this hinge represents that.
I needed to get that door up and I really wanted to make it something special. I didn't just want
to put it up on commercial hinges like the old door had been. I wanted to make this something
that really represented my work and who I am as a blacksmith and as a woodworker because I am
building the door down in the wood shop. Doing more of my own personal projects also means that
there may be fewer videos here on Black Bear Forge as 2025 goes on because I'm going to put more time
and more effort into each video. I've been working on these hinges off and on for week, week and a
half and I've been working on the door on some of those other days. Plus being winter just means I
don't get to the shop quite as much. So it does take a little longer to get everything done and
a video at all. But by not taking time away from projects like this to make just a short simple
video just for the sake of making a video, I think we can look at some better projects, some higher
quality work. I can express my own creativity and hopefully I'm encouraging you to do the same.
I really want to inspire you to get out and try and do things that are maybe a bit more of a
challenge and represent your best work. I don't know if these hinges are necessarily my best work
but they are certainly the fanciest set of hinges I have ever made and perhaps the most fiddly set
of hinges I have ever made. So I'm really enjoying the process. I really like doing things this way
and I hope you'll stick around and watch all the videos that I have planned this year not only here
on the Black Bear Forge channel but on the other channel, the John Switzer channel, which is where
the woodworking, home improvement, construction type projects are all going to be and I have lots
of those that are going to keep me busy this year. We've been watching rolling the eye on the other
part of the hinge. This is the part that'll mount to the jam and it's really about the same other
than the fact that this is a wider piece of material. This is a three inch wide piece of
material but the process is essentially the same. Once I have the eye rolled I'll let that cool down
and I'll lay it out for a decorative end on it. I'm going to go with a kind of a three-lobed end
and a little bit of the scroll work so this will have a unique element to it and also the element
that complements the main strap of the hinge. There are lots of different ways you can do hinges and
back plates. I did several test pieces of different things and this is what I decided I really liked
so this is what we're going to look at here. All roughed out under the bandsaw and for that it's
going to need a little bit of grinding to clean it up some but as always files are going to be the
way we do this in the end. This just has two little scrolls one on each side so it's a lot
faster than the four scrolls on the long hinge. This back plate is the one that will go on the
two longer straps. The little shorter strap that I did not put the extra scroll on will have
something different and I'm not going to look at making that. I think you'll be able to see how it
was done in the photos at the end of the video and we show the close-ups of the finished project
so we're just going to look at doing this one but in reality it's the same stuff we've been looking
it a little bit more interest and highlight the shape that I've got here. You certainly don't have
to do this kind of work but I think it's the kind of thing that takes work from being kind of
average to being a little extraordinary and really can elevate your work and develop some
skills you might not have without really costing a lot. Most of the chisels you can make yourself
they don't take a big expense in materials you can make them out all sorts of different tool
steels whatever it is you like to use. It's a good excuse for making more tools as well as doing
some more decorative work. Of course everything is laid out cold and then the lines are chased
in deeper while the material is hot and on these lines I'm going to come back with a butcher tool
this is kind of a single bevel tool these are straight side on one side a bevel on the other
side and this just gives the piece a little bit more depth and make it look a little bit more
three-dimensional than just the plain chisel line. Butchers are frequently used in a first and second
pass configuration the first pass butcher is a little bit steeper and the second pass butcher
is a little bit flatter but you need to use them in the right order if you use a second pass butcher
first it tends to jump out of the chisel cut. On these tighter curves I have to use a very narrow
set of butchers just so I can scribe that circle the big wide one would not follow around that
circle but it's real easy to drive these too deep so you got to be real gentle doing this
even working down to a black heat or finishing it up cold can leave a smoother finish so it's
just a matter of what you need to do to try and get all the tool marks out of there after you're
done this is really difficult to get into and file since they can't pass a file through so the cleaner
you can do the butchering the better off you'll be. Now I am jumping from one part of the hinge
to another a little bit here I'm letting that other piece cool so I'm going to go ahead and
drill the holes in the long strap while that's cooling and I just lightly deburr these I'm going
to use round head wood screws on these and I think they look the best in this particular
situation they kind of remind me of rivets and they add a bit of a decorative element versus
just a regular flat head screw a little bit more chisel work just to do something in the
middle of the strap again not strictly necessary by any means it's purely aesthetic but I think
it adds something to the work it's just another place for some self-expression
remember blacksmithing is art and it's okay to express yourself in your artwork
these are set in cold and then come back hot and deepen them a little bit Francis Whitaker
always said if you're going to make a mark make it deep enough for people to see
I'm putting my touch mark and the year on these that's something I'm going to start doing this
year I've always thought it would be a good idea to put the year that work was done on there
both for my own record and so people don't ever pass it off as an antique I don't want
anybody trying to sell these as a 200 year old set of hinges in an antique store someday down
the road so I think putting the year 2025 on there is worth the effort to do at least on the
more unique work I don't think I would do that on all my work but on things like this I'm going
to try and get in the habit of putting the date on there I just ordered a stamp from an industrial
supplier that had the date filing things clean is one of the best ways to get everything shaped
just the way you want it and then I'm going to cut the knuckle out on this I'm going to
cut it on the little porta band I can't turn a tight enough corner to clean all this out
perfectly flat but I can kind of nibble away at it a little bit we'll come back and clean this
up with a file and as we do the filing we'll also do some fine fitting of the joint to get everything
to fit properly I also like to file a little bevel on there just to make it look a little
bit cleaner it isn't absolutely necessary this is where we make sure the hinge pin fits just right
I run a 3-8 drill bit through there and then I'm using a 3-8 cold rolled pin cold rolled is exact
size material so it's exactly 3-8 and fits perfectly in the 3-8 drilled hole using a torch
I heat the end of the rivet head I don't need the whole thing hot so I don't want to put it in the
forge just need a little tiny bit of heat and I'll put a head on the rivets that this is not a big
domed head you can certainly use rivet headers and put a nice domed head rivet on there if you
want to I just need it to be enough that it doesn't fall through you can also make something
really big and ornamental if you wanted the rivet or the pin to be part of the ornament of the hinge
then a final heat to do any last minute straightening things sometimes get bit during
the assembly process at that point I wire brushed it one more time then I put a paste wax finish on
as it starts to cool down I want this to be just hot enough that the wax melts and smokes a little
bit but not hot enough that it actually burns the wax off and there is a set of strap hinges completed
these are a little bit over the top fancier than most doors need the fancy stuff doesn't help hold
the door up any better but it's a chance for me to express some creativity try some things out
that I've seen in my head and I haven't had a chance to do and do something that probably I
don't have a customer waiting to pay me for and I really enjoy doing these projects plus it makes
the shop a more enjoyable place to be in when I have more of my own work on display here in the
shop so I'm really glad that I got a chance to do these hinges I'm going to enjoy having them in
problem is the door still isn't finished so I'm not going to be able to show these on the door
or at least not on the door hung up in place I can show them on the door down in the basement
wood shop but once the door is done I'll get these on there and there will be a video over
on the John Switzer channel which is where I'm leaving most of the woodworking stuff now
that covers the building of the door itself I want to thank each and every one of you for stopping
by and watching the videos if you haven't subscribed already I'd really appreciate it
if you subscribed I'd love it if you'd hit that like button those things really do help make a
youtube channel successful I'd also like to give special thanks to my channel members and my patreon
patrons who help make these videos financially viable for me to do and take the time to video
these projects channel members generally receive early access to the videos a day or two early
and patreon patrons not only receive early access but they receive the videos ad free so if you
don't like the ads on the videos and you want to see them a day or two early maybe friday or
saturday instead of waiting till sunday morning patreon is a great place for that but again thanks
to everybody for watching the videos I hope you have time in your day to get out to your shop
make something but stay safe wear your safety glasses we'll see you for the next video