Making Probably The Most Heat Resistant Material

Terrific Physics
40 followers
Hello everyone, I will look at the huge rockets being built now, and I'm amazed.
Not only is this giant 50 meters tall, but it can also return to Earth by itself,
and withstands enormous temperatures during re-entry into the atmosphere
at speeds over 17,000 kilometers per hour. Apparently, to withstand such harsh conditions,
it has some superheat-resistant materials attached to its body.
I wonder what the thermal protection of such a rocket is made of and if it can be made by oneself.
But let's figure it out.
To find out what the cladding of new rockets is made of,
I decided to first search for information on the internet.
Turns out that it is made of silicon dioxide, which is essentially ordinary sand.
But if you search for photos of such cladding online, it doesn't really look like sand.
Most likely, the silicon dioxide is in some other form here.
To know for sure, it would be good to obtain that very cladding from the rocket for study.
After several unsuccessful launches of that rocket,
fragments of its cladding were found around the world and sold at auctions.
But their price didn't particularly please me,
so I will have to find out its composition by some other method.
That is most likely, by trial and error.
First, let's take a look at what heat-resistant and thermal insulation materials containing
silicon dioxide are available, and which one would be best suited for making rocket cladding.
The most well-known and commonly used is ordinary firebrick,
which is made from fireclays containing about 40% aluminum oxide and 50% silicon oxide, such as...
The rest consists of various impurities.
The melting temperature of these components exceeds 1500 degrees Celsius,
which makes the resulting material quite resistant to heating.
However, under certain conditions, it can still melt, as in one of my previous experiments.
Here we tried to melt zirconium using an oxygen torch, but in the end,
zirconium did not melt, while the firebrick underneath did start to flow a bit.
However, firebricks, although quite heat-resistant, are also very heavy,
so it is not possible to make rocket cladding from them.
In addition to bricks, the store also sells what is called potassium wool,
which also withstands very high temperatures without melting or losing its properties.
It consists, like firebrick, of a mixture of melted aluminum and silicon oxides.
The only problem is that it is fragile and easily crumbles in your hands.
Such a material is unlikely to withstand the immense speed
when the rocket enters the dense layers of the atmosphere.
In search of other fireproof materials, I decided to turn to some rather unusual ones.
Who knows, they might also be suitable as rocket cladding.
In the 1980s, a certain Maurice Wald invented an unusual fireproof material called Starlight.
At first glance, it looks very much like those same resilient tiles,
so I decided to try making it as well.
Fortunately, the components for making this material can be bought in any store,
namely regular starch, baking soda, and PVA glue.
First, you need to mix starch and baking soda in specific proportions you see on the screen,
and then mix them well in dry form.
After that, I pour PVA glue into this mixture,
and give the substance the consistency of regular dough.
This took quite some time, and theoretically the material is now ready to be used.
As the first demonstration test, I decided to take a regular chicken egg
and coat it with Starlight on one side,
after which I began to burn it with a torch for one and a half minutes.
Interestingly, when heating this material,
it began to form something resembling charcoal foam,
which I assume plays the role of thermal insulation.
But how can you chew the egg after one and a half minutes of intense heating with a powerful torch?
Surprisingly, it turned out to be even slightly warm, and its contents remained liquid.
For another test, I placed some Starlight on my hand,
after which I began to burn it with the same torch.
Yes, you can hold on for about 20 seconds,
but then this material starts to heat up and it becomes uncomfortable.
Yet my hand did not get hurt at all.
In principle, the same Starlight can be dried,
but it is unlikely to be used as rocket cladding,
as it easily gets wet in humid air,
and during atmospheric entry, it will most likely just burn up.
But for demonstration, yes, the material is quite interesting.
After all, I got tired of pointing fingers at the sky,
and decided to look for something similar to the heat-resistant tiles of the American rocket
at auctions for study.
Unfortunately, there were no tiles from the rocket itself,
but luck smiled upon me,
as someone from Canada was selling heat-resistant tiles from the Buran,
the Soviet reusable space shuttle,
which unfortunately flew only once.
Essentially, the thermal protection of both the rocket and the Buran should have similar properties.
It's interesting, of course, how the heat-resistant tiles from the Buran ended up in Canada,
but that's not the point.
I'm buying.
A few weeks later, I received the package.
The very heat-resistant tile from the Buran.
It turned out that it is not from the shuttle itself,
but from either a model or a copy,
as the seller indicated that it is from some Buran 2.0.
But most probably, most likely,
it should have the same properties as the original tiles from the Buran that flew in space.
I think that for the sake of science,
one can even have a little fun with this piece of history using a powerful gas torch.
Yes, apparently this is the very thermal protection,
as such a tile easily withstood a minute at a temperature of 1200 degrees Celsius,
and it cooled down almost instantly,
which is even noticeable on the thermal camera.
After cooling down,
I also decided to check how this tile would heat up from a sufficiently powerful gas torch,
for which I started heating it from the backside,
and monitoring the temperature with the thermal camera.
The heating time was two minutes,
after which the tile began to gradually heat up,
but only by a few degrees.
Now this is what I call thermal protection.
Despite its large size,
such a tile weighs about 200 grams,
which is quite light for its large volume.
If you actually look at the backside,
you can see the material from which this thermal protection is made.
By feel and sound,
it resembles very light wood,
although it is most likely some form of foam silicon dioxide.
I think I need to try to find the composition of such thermal protection on the internet.
After searching again in Russian,
I could only find that the white part of this tile,
which is the main thermal insulator,
consists of ultra-thin and pure quartz fibers.
Interestingly, at first glance,
this white substance does not resemble fibers at all.
Apparently, there is some technology here that is not mentioned much on Russian language sites,
after some thought I decided that,
in essence,
Buran was an improved copy of the American shuttle,
which had a similar design and thermal protection.
Therefore, I decided to look for the technology
for making heat-resistant tiles used in the shuttle.
I think they wouldn't differ much from the thermal protection of Buran.
After a couple of hours searching on American sites,
I found this 1976 patent,
which described in great detail the technology for producing
that very white part of the shuttle's thermal protection.
At first glance, there's nothing complicated here.
I just need to find suitable materials.
It took me a few months.
The most challenging part was finding and purchasing this ultra-pure quartz wool,
which essentially is the microfibers used in the production
of heat-resistant protection for Buran and the shuttle.
They are produced only in a few countries around the world and are quite expensive.
A kilogram of such fiber certainly costs 120 euros.
It feels like very high-quality viscose cotton wool.
At first glance, you would never think that this material
can literally withstand temperatures up to 1600 degrees Celsius.
Well, after I obtained this rare quartz fiber,
I can try to make that very skin for Buran.
Just a little.
To start, according to the patent,
you need to measure a certain amount of quartz wool.
I took 115 grams.
At first, I thought about tearing it into small pieces.
But due to the formation of a large amount of not very useful quartz dust,
I decided to cut it with a knife instead.
After I weighed the required amount of quartz fiber,
it needs to be dissolved, or at least evenly distributed in water.
This task is not the easiest,
as the quartz fibers here are quite long and strong.
Therefore, I decided to try grinding them with an immersion blender.
To my surprise, this method worked brilliantly.
After a couple of minutes of grinding,
I ended up with something resembling quartz pulp.
Now, according to the patent,
it is necessary to add binding agents to it,
one of which is colloidal silicon dioxide.
Fortunately, unlike in 1976,
this substance can now be easily found even in pharmacies as an adsorbent.
For my experiment, I will need exactly 13 grams,
which I weigh out into a glass cup.
In addition, as a primary binder,
I also need to add 9 grams of regular starch.
Potato starch will do as well.
To help this mixture blend better with the quartz pulp,
I add a little more water and mix it with the same immersion blender.
Interestingly, the initially thick mixture became much thinner when mixed.
Apparently, the colloidal silicon dioxide
binds better with water molecules during such mixing.
All that's left is to combine the quartz pulp with the binding components,
and the kitchen blender is once again indispensable here.
After
All that's left is to get rid of the excess water,
using regular cheesecloth and a colander.
As a result, I ended up with this lump of quartz fiber along with the binder.
Well, next, according to the patent,
oh, it seems I got carried away and missed an important step
to alkalize the obtained mixture with ammonia.
Well, okay.
I'll have to dilute everything with water
and add more ammonia to the obtained mixture.
After mixing, I check the pH level using indicator paper,
and according to the instructions, it should not be higher than 10.
That's basically acceptable.
Now, all that's left is to get rid of the excess water again,
but I can't squeeze much moisture out of this lump with just my bare hands.
I need something like a press.
It's good that I decided in advance to make a kind of homemade and very primitive mold
from an unconventional tin bottle in my new lab.
First, I need to cut off the bottom of this container,
which I decided to do with a Dremel, as I didn't have a grinder on hand.
The Dremel came with metal discs,
but if I had known how low quality they were,
I would have slightly borrowed a grinder from friends.
After some time, with great difficulty,
I somehow cut off the necessary part of the bottle,
in which I also made several holes for water drainage.
All that's left is to remove the burrs and,
voila, the primitive mold is ready.
I am now placing my quartz pulp into it, layering everything with gauze.
At first I squeezed out the excess water just with my hand,
but in the end I decided to press everything down as best as I could,
using my weight.
Most of the water came out.
Now all that is left is to remove the resulting workpiece from the mold,
and it's not that difficult to do with the help of gauze.
The only thing that significantly bothered me was that
I lost a lot of binder during the manufacturing process,
which was partially washed out during the first pressing,
when I had forgotten to add pulp to the mixture,
so from the remaining quartz fiber,
I decided to make another batch of quartz pulp,
this time clearly following all the instructions from the patent guide.
In the end, after removing the excess moisture,
I ended up with two more of these round pieces,
which turned out even a bit better than the previous ones.
Now these workpieces need to be thoroughly dried,
as they all currently weigh over 200 grams,
which means they still contain a lot of water.
I decided to dry the obtained round pieces in a regular oven
at a temperature of 125 degrees Celsius for 15 hours.
Well, see you tomorrow.
After the drying and cooling time, the blanks became much lighter,
which is clearly visible on the scales.
Now these disks are already very light, but they are still not completely uniform,
and in order for them to become true high temperature thermal insulation,
they need to be fired.
And not in a regular oven,
but in a muffle furnace at a temperature of 1200 degrees Celsius.
Nevertheless, I now need to fire my quartz fiber blanks.
To make everything faster and save on electricity,
I decided to fire them all together,
simply laying potassium with new cotton.
To begin with, according to the patent,
the blanks need to be gradually heated
so that the residual moisture can evaporate and cracks do not form.
Therefore, I first heat them to approximately 500 degrees Celsius
and keep them at that temperature for half an hour.
During this time, the starch begins to slowly burn out of the blanks,
causing them to darken slightly.
After that, I raise the temperature to 700 degrees Celsius
and heat the blanks thoroughly for another 30 minutes.
Now they have turned white,
which means the starch has completely burned out.
All that's left is to raise the temperature to 1200 degrees Celsius
and keep the blanks at that temperature for two hours
so that the quartz fiber fuses together with the colloidal silicon dioxide
as a binding agent.
Well, at the two-hour mark,
I turn off the furnace and let the blanks cool down.
Interestingly, during the cooling of the furnace,
I noticed that its insulation cracked quite a bit
during the high-temperature firing, which was unexpected.
I don't think it should be like that.
Apparently, Chinese furnaces are not very high quality now.
Write in the comments what you think about this.
After the furnace cools down, I take out the blanks,
and in my opinion, they turned out just perfect.
During sintering, all the cracks simply disappeared
and the resulting thermal insulation samples turned out to be very light,
without internal voids and quite even.
Now they really feel like that white insulation from the tiles of the Buran.
Now it is advisable to process them to give them a more even shape.
For this, I first saw off a thin layer from them using a metal cutting blade.
It doesn't require much force here, as this material is cut quite easily.
And of course, I do all this under a fume hood to avoid breathing in quartz dust.
After rough processing, I sand the resulting blanks with a regular cloth.
Fortunately, this material is very soft and pliable,
making it even easier to work with than foam.
I decided to give one of the blanks a square shape, similar to the tiles from Buran.
Of course, the thickness of my homemade thermal protection is not the same as in the original,
but for now, I am satisfied with the result.
The only thing that currently distinguishes my homemade samples
from the original thermal protection is the coating, or rather, its absence.
As far as I understand, heat-resistant tiles with some black coating were used for the
cladding of the lower part of both the shuttle and Buran, likely for better heat dissipation.
How to make this coating?
Once again, American patents come to my aid.
In one of them, I found how to make a special heat-resistant black paint
for the white thermal protection that I made earlier.
For this, I will first need borosilicate glass powder,
which I decided to make from several old heat-resistant test tubes.
In addition to glass, 1.5 grams of silicon diboride will also be needed,
a black compound that acts as a high-temperature alloying agent.
In addition, 20 grams of molybdenum disilicide need to be added to the mixture,
which will create a thermal emission layer.
In simple terms, it will be better to dissipate heat from the overheated surface of the thermal
protection. All that's left is to grind all the components well, for which I took a regular
coffee grinder. Yes, it's better not to breathe this dust.
According to the patent, it is better to apply this mixture using a spray gun,
but I don't have one. So I simply mixed the resulting mixture with ethyl alcohol
and began applying it to the quartz workpiece using a regular brush.
Now all that's left is to bake this coating in my already crumbling oven
at a temperature of 1200 degrees Celsius for an hour.
Interestingly, even with a quick opening of the oven, it is evident how much faster the
thermal protection begins to cool compared to the white walls of the chamber.
This is all because a black body radiates heat better than a white one.
Therefore, the lower part of both the shuttle and the burin was covered with black heat-resistant
tiles so that they could cool down during entry into the dense layers of the atmosphere.
After cooling, my painted thermal protection tile can be examined up close.
As can be seen, at least on one side, the coating turned out to be quite even.
Although after sintering, such a tile has shrunk a bit.
Apparently, part of the quartz fiber fused with the black coating.
It is interesting to see how quickly it will cool down when heated with a gas torch.
Yes, as can be seen, this happens quite quickly, as evidenced by the readings of the thermal camera,
especially when viewed from the backside of the tile.
The same tile, only white, cools down a bit more slowly,
although due to its greater thickness, it does not heat up as much.
In addition to the round heat-resistant tile, I decided to make a small square one,
also painting it with a black coating, after which I baked it in the oven.
If we compare how my homemade tiles behave compared to the original from Burano,
the difference is not particularly noticeable.
The black coating re-emits residual heat very well,
while the quartz filling prevents heat from penetrating deeply into such thermal protection.
In the end, I believed in my homemade thermal protection so much,
that I decided to protect my hand from the hot flame of my quite powerful gas burner.
In principle, it holds up calmly for about 30 seconds,
and I did not feel the slightest heat on the backside of such homemade thermal protection.
Moreover, certainly, even my small tile can protect the hand from the hot flame of the burner.
So, in principle, I absolutely believe that I have created that
heat-resistant tile from American rockets, or from the Buran Space Shuttle.
Well, I think after watching this video, you learned how to make a real shuttle cladding,
or for that American rocket in semi-handmade conditions.
But if you liked this video, as always, don't forget to give it a thumbs up
and subscribe to the channel to learn more new and interesting things.
