How to make a Shark Leader - Ultimate Heavy Duty Rig This instructional video will teach you how to make a super heavy duty shark rig. This shark leader is for land based shark fisherman that paddle there baits out past the surf. It is very simple and anyone can make them with minimal practice. I will list all of the components below. I hope this vide helps you and you find it educational. Tight lines everyone!
1000 lb. Monofilament Leader material Large Crimping tool Heavy Duty wire cutters 600 lb. 7x7 stainless steel wire cable 1000 lb. mono crimp sleeves 800 lb barrel swivels 16/0 - 20/0 Non Stainless steel Non-offset circle hooks Electrical tape Tape Measure
NOTE: The video accidentally says Stainless Steel Circle Hooks on one of the screens. It is supposed to say Non stainless steel Hooks. Sorry for the Misprint!
hey guys Sean from lost ID I'm here
today to show you how to make the best
shark leader I know how this is a super
heavy-duty shark leader for land-based
shark fishing when you're paddling out
your baits and dropping them 100 500
yards from the beach
this is the kind of setup you want to
use when you're fishing for large sharks
off of the beach here's a finished one
right here you've got your mono leader
is connected by swivel to your steel
cable and then I like to use a double
hook rig that way you can hook the front
and the back of the fish that way if you
get a short strike you'll still hook
them you will hook some smaller sharks
like that but that's the price you pay
for trying to get more hook ups so let's
get started here's all the materials
you're gonna need I've got a thousand
pound mono leader material I got that
off Fullbuster comm got some a FW 49
strand seven by seven stainless steel
wire some people like to use single
strand wire they both have certain
advantages over the other I just prefer
the seven by seven four nine strand wire
because you don't get nearly as many
kinks as you do with the single strand
wire you're gonna need a large crimping
tool you can get these at Lowe's or Home
Depot you need gonna need wire cutters
preferably heavier-duty once cut through
that steel cable we're going to need
crimps
these are called crimp sleeves you need
crimp sleeves for the thousand-pound
mono you need heavy-duty barrel swivels
the electrical tape and a tape measure
most important you're gonna need some
good stout hooks okay let's get started
with the mono you need wire cutters cut
the end of this and the length you want
I like to use five to six feet of the
heavy mono leader and you can use a tape
measure which is good but I know that my
reach from fingertip to fingertip is
about five six so what I do is I just
take it stretch it out once come back to
where that hand is stretch it out again
and I know I got about 11 feet of mono
right there okay so we've got our piece
of mono cut let's cut our steel cable
and I use just about the same length and
the steel cable about five to six feet
and I do it the exact same way stretch
it come back
[Applause]
[Music]
stretch it all the way out okay right
there I know that I got between five to
six feet now we got our wire cut so we
got about five and a half feet of
stainless steel cable and five and a
half feet of a thousand pound mono first
thing you're gonna do is take one of
your crimp sleeves you get these off of
Fullbuster too for the thousand-pound
Mona you're gonna slide your crimp
sleeve on like that you'll push it down
I always used my index finger and thumb
I go down about that far then you're
gonna want to put your swivel on okay
you're gonna bend it over and you're
gonna slide both of those lines through
the crimp sleeve like that push it up to
where it's firm and snug then you grab
your crimps and when you get them you
just kind of experiment see which one is
the right one slop to use for the
thousand-pound and you get it started
that and let me show you here I'm
leaving you want to leave a little bit
of space right there because you want
you want your crimp to do what's called
flare I'll show you here in a second get
it in there you squeeze you got to do
one on that end of the crimp let's see
we got one crimp done right there and
then we're gonna want to put another one
right there
so we're gonna squeeze that through
again we're leaving some space on the
end there okay squeeze all right now can
you see the flaring right there that's
what you want you want that crypts leave
at the ends to be flared out kind of
like an hourglass shape you see how
that's an hourglass shape right there
that's how you know you got a good hole
there okay all right let me do that to
the other end and then we'll get on to
the wire now we got both ends with a
barrel swivel and a crimp sleeve that's
crimped twice next thing we're gonna do
is you're going to take a wire okay this
is the most complex process out of the
whole thing you've got seven strands of
wire here you have to separate it into
strands of three and four so you've got
one section of four right here
one section of three right here so
you're gonna unwind it into two sections
you're gonna go down from your index
finger to the end of your thumb which is
about eight inches like that you've got
your two sections here take your barrel
swivel now slide one section through
will that drop down now you're gonna
cross these over just like that okay
you're gonna run the wire through
there's two ways that wire can go
through you see how it's not locking on
each other right there that means I've
got it backwards so I've got to take
that out you look and see how you had
them crossed and you do it the exact
opposite so now I'm gonna bring that
wire through from the other side you're
gonna notice the big difference here you
see how those strands have gone together
right there they're smooth so you're
gonna take it you're gonna run it
through again and it's gonna lock right
back in smooth again now you got your
barrel swivel down here so you're gonna
run that line through the barrel swivel
bring it up towards on the part that's
wrapped already we're gonna do one more
still gap there and run it through one
more and there's still another gap so
one more time okay now you see how that
just looks like the regular steel cable
right there now we're gonna drop
that barrel swivel down and you're gonna
do the same thing on this side you can
pull it through and wrap pull it through
and wrap until you come all the way down
to the end okay it may take a few times
to get the hang of it but once you
figure out how it works you'll you'll
get it and it won't be never be a
problem again so you got your two tag
ends here now loose so what you got to
do you got to take these two combine
them make it into another piece of
regular steel cable just like that so
you figure out which way they're wrapped
and then you start going wrap it making
tight wraps with them okay
you see how that's turning in one steel
cable there you go all the way down like
that okay now you got it okay we're
going to go through we're going to do
that with the hooks then we're going to
come back and we're going to take these
so we've got 18 off circle hooks they're
straight shank
[Music]
they're not offset the new regulations
coming out say you have to use non
offset non stainless steel hooks and
these aren't stainless steel either
those are the new Florida shark
regulations coming out so you're gonna
take your wire you're gonna thread this
one on you want to go through this way
you're just gonna leave that for now now
you're gonna take your other hook and
you're gonna do this one just like we
did the joint there I'm gonna put it
through one side and make your loop
let's go this way I think that's a great
way and you're gonna bring one through
the loop and see if it locks in okay
locked in we want to get that smooth
okay we got like that so you know you've
got it correct you're gonna pull that
through see how smooth that is right
there and we want to get our hook back
over this part that's got the dump two
sides joined together so we're gonna
stick this through the eye the hook just
like that slide the hook back so now
that hooks out of the way so we can
finish wrapping this okay got enough
space for one more okay that side direct
drop the hook over to this side
here again one more we've got enough gap
for one more wrap go through one more
time bring it down okay so this is gonna
be the exact same way get the other side
we're going to get these wrapped
together all right got it started right
there see how I got started we're gonna
wrap this all the way down make sure
that's smooth all the way through you
can see got that so now you can take
this hook you can run it through the
gill plate pull it back to the back of
the shark tuck that into the back making
sure it's exposed out and you can take
this one you can hook it in the jaw
right here so you've got your shark
hooked at both ends let's finish this
out let's get these in taped up that's
what we've got the electrical tape for
so you don't want these tag ins flying
around they'll pick up debris you can
just make a mess if there's gin grass
out and you're trying to reel up
something like that
we'll pick up pick up a crazy amount of
pink grass so just gonna take your
electrical tape start there I'm just
going to wrap it tight
Titus your app I want to go all the way
over the tag end wrap a couple times
you're good
[Music]
this rabbit neck on itself okay that's
it got a shark later done finished now
I'll show you how I like to store it mr.
baggie all right
besides I hooks they are on the outside
of the baggie just take your leader
start rolling it up tight
fired just do the same thing eggy up
slide it in kind of unravel four bills
the baggy there you go
you're all set easy to do it's not hard
a buddy of mine showed me how to make
these he's an avid shark fisherman he's
reeled in multiple Makos on rigs like
this so these work
you got your mono leader to protect
against a tail whip and you've got an
excess of wire there just in case the
shark rolls around wraps up in the
leader and gets another part of it in
his mouth tend 11 feet of that should be
enough that even if he does roll around
get wrapped up and gets it back in his
mouth he's still gonna have the wire
leader in there so I hope you guys
enjoyed the video don't forget to Like
and subscribe I really appreciate all
the support tight lines everybody and
see you next week
[Music]