Diamond Trilogy Ring

Handmade Jewelry
2 followers
Mar 14, 2025
This video shows you how a diamond trilogy ring is made using old school techniques.
For more details on how to make this ring go to: https://www.jewellerytrainingsolution...
In this video I'm going to show you how to make this beautiful trilogy ring. I'm just going to
make three very simple bezels to start with and I'm just going to form them with my pliers.
So I've annealed this and the measurements of this, I almost forgot, is one mil thick
and it is four and a half mil wide and that's 60 mil long at the moment. I'm not going to need
anything light that much. So I'll square off the end first of all and I'll just start turning the
metal from the end. Grab the end of the strip and bend it around like so. So I'll start by making
the centre setting and what I want to do is make the the bezel pretty much the same size as the
diameter of the stone which for your interest is it's six and a half mil so that's quite standard
for a one carat diamond. So I'll do a little bit of forming in my blocks once I've soldered this
so you can see there that when you look down you can't see the metal. So I just need to cut
the strip at this point here so that when I close it up it will be the right size.
pair of pliers so I've got my round nose pliers and my chain nose pliers and get the joint
together like so. You want it to overlap a little bit like that and then just squeeze the
end of the strip into place and hopefully it'll land nice and tight like I've got it there so
that's ready for soldering. So I'll do the same for the other two and before I do solder them
I'll just make sure I don't need to cut any metal out to make it any smaller. I think it looks okay
yeah that looks fine so I'll close the other one and then get them soldered.
Okay I've got my 18 carat hard gold solder I'll just cut three little pieces off there
and flux the joints and the solder and I like to pick the solder up once it's melted into a ball
and then just place it on the joints as the metal gets to soldering temperature.
Okay I'll pick those. So now I'm going to change the shape of the bezels to a very slight taper
so the 17 degree collet block if I use this in the normal way and made them the 17 degrees
it would make the three settings together splay out too wide so they wouldn't be the right shape
when they're put together so it just it needs a very slight taper to get a very slight curve at
the top of the ring to make it look right. So the way to do that is I will just put them into
one of the holes that it fits into give it a couple of taps so this
will help to make the bezels perfectly round as well and then this punch here has got a
long taper so you can use anything that's round to do that and you can even use
the standard
punch that you get with a block although this one it will spread it out a little bit too far
but you can still work with it. So I'll just leave it at that for now you can see that the bottom of
bezel is smaller than the top so once I've done that to the others we'll see how that spreading
is looking. One of the side settings just needs to go a little bit bigger to match the other side
so I'll just tap it open a fraction more.
Okay that's the three of them together now so as I said earlier we'll check and see what
it looks like when they're all together.
Okay that's the three settings together and with the stones in place and there is
as you can see a gap between the stones that's not going to be the case once I've set it up
properly because what I'll be doing is filing where the joint's going to go and that'll close
everything right up. The solder joint I did earlier it's not the best solder joint in the
world but it doesn't matter because that's where I'm going to be soldering next so keep all the
solder joints together whenever possible. I'm just putting a little cut on top of the big setting or
middle setting just where the solder joint is and then I'll just line up
directly opposite just put a little cut there now all this is going to help me line everything up
later. Yeah that's going to be nice and tight. Oh yeah that works and I've still
got the option to just drop the top of the setting down a fraction so I'll use my
spring-loaded tweezers.
Just need to make sure the side stones drop down and stay level.
So I'm just going to burr out the middle of the or the side of the middle stone.
Okay that works better. I'm just going to make some final adjustments to make sure that when the
stones are in place that the contact between the underside of the middle stone
and the crown of the outer stones I don't want there to be too much contact because
that could break the stones. I'll show you what I mean. Okay so that's what I'm looking at there
there's a slight gap I hope you can see that between the crown of this stone here and the
pavilion of the middle stone so when it comes to setting the stones later if there's too much of a
contact then it can cause unnecessary pressure on the stones and even though they're diamonds
they will break with pressure in the wrong place.
Because of the way that the stones are spaced out it looks like I can get the
center claws right into the edge there the end of this drop here and the same on that side.
I've just put very faint markings because this pen's just...
and the piercing saw is great because you can just rest it on top of the setting
make sure the opposite claw goes to the opposite spot.
So again place it on top.
It works really well so I'll just cut those markings onto the side of the bezel.
This is a 1.2 mm cross-cut tapered burr which is the other way of doing it and this will get a
much rounder shape to the groove so it's good to finish off on this one.
See how that looks. Okay I'll give that a push and see if we're in. I don't think it's too far off.
Okay that was much quicker. Okay I'll do the other two and then I can solder them.
right through the groove and get the claws perfectly soldered it means that the solder
will no doubt run right through the middle there which is okay and later on when it comes to
setting the stones I can just split these claws as needed. So now I've put the end claws on so I'll
put some grooves in on the ends and I'll do it as I did earlier first of all with the saw cut.
And I'll flux the grooves so I'll just place the wire onto the groove. Okay so that's one side.
I'll do the other side and then I'll clean the setting up ready for putting it on the shank.
I've got here marked at the ends around about 7 mm and that's what I'm going to leave for
the shoulders. So I'll put the middle part into the wire sections and just roll up to
those black marks. So keep an eye on what's going on at the back. Tighten the roll up by
turning the handle. Turn again. Let's see if we've got it up to the right point here. Yep so turn it
90 degrees. It goes without saying that this has been annealed
into the right in the centre. That one there which looks about the right shape for what I want.
Tighten right up. Roll to the marks and see what we've got there. So we've got a nice
D shape. It's still a little bit thick so I can stretch it out a little bit more.
So this needs a really good solid hammering at the end and that will change its shape from square to
the half round shape and also just spread it out a little bit so hopefully it will just fill the
area at the end of the settings. And now I'll bend it into shape. So bend the ends first.
Okay it's not far off and I'm just checking to make sure I've got the correct angle which I have.
I'm just going to need to trim off a little bit off the sides. Just flatten the sides so that it
does fit snugly between those claws. I also need to tidy up the ends before I can attach it. So
okay it's ready for soldering now. But off camera I did spend quite a bit of time setting it up
and just trimming and shaping until it fit really nice and there's a minimal gap there.
So it won't interfere with the medium soldering that I did with the white gold earlier.
So I'll just prepare to put another piece on if need be.
Pop a bit more there. Make sure it's run to the top and just get this one in place.
Then I can do the rest of the work with my tweezers. I've got my larger soldering tweezers
here. As the solder melts I'm just going to push it down slightly. Not too much, just a fraction
on the solder mat. That's enough. I can see that it's just budged its way down
a little bit. So to do a proper check just look at the top and make sure that I've got the same
amount of bezel showing on both sides. And that is the case so we're all done.
Okay now blend the bottom of the setting in with the shoulders.
I'll be taking some of the height off the setting as well.
Split the claws now with a 6-0 saw blade.
It's really important to polish the inside of the setting so before it goes in the
pump tumbler I will use this bullet shape brownie to give it a much better finish.
I'm going to start by setting the two outer diamonds first
and I'm going to put a seating cut just slightly above the top of the
bezel because these are quite low set and will rest on the bezel. To put the seating cut in
I'm going to use a 3.2mm heart bur so a larger heart bur would be better but I haven't actually
got one so I'll use this. So I'm going to put a cut on the two claws next to the centre stone
and I'll repeat the process on the other side.
Just stick my pen knife in at the split just to separate the claws a little bit further
and just squeeze the claws evenly and that should lock the stone in place. Do the same on the other
side. You can use a stone pusher to do this but if you're confident with your pliers and
you don't feel that you're going to slip then this is a much easier way.
I'm quite happy with that. The way that the centre stone is
sat there there's still a gap between the stones. I can just see on the sides there
so where I'm cutting the seating cut spots before is about right so they're only slight cuts again.
You've got to make sure that they are lined up properly so that
the stone doesn't drop onto the outer stones towards each other. It's very easy to slip off
with your pliers so again if you're not confident doing it this way then use a pusher but you need
to brace the ring in a bench make to make sure you've got a really firm grip. I'll use a barrette
I'll just get rid of the tool marks around the claw tips then I'll give it a polish.
There we have it set, polished and finished. I hope you enjoyed.
