Cách di dời nhà của Trung Quốc khiến cả thể giới phải ngả mũ bái phục. Họ đã làm như thế nào?

My dear friends, the story of leaving home for a new place is no longer unknown to us. There are many projects around the world that have been successfully implemented using different methods. These houses with all kinds of sizes, weights, ranging from a few hundred to thousands of tons. But the way China's unique home is left makes the whole world admire it. You don't have to keep your house like this. So how did they do it? Watch the next part of this video to see how they do it. An old building in Shanghai was recently abandoned on a walking robot. It takes 18 days to leave Lagena Elementary School to a new location. The project was completed on 15 October 2020. The unique feature of this project is that the building has almost 200 hydraulic support rails below. When the building is moving, the supports move like a man walking. In general, the building is moved by an optimal solution than with the methods of moving by cable or by a flat way. The other methods did not meet the requirements when I left this building. Finally, the method of leaving by walking has been discussed many times. The building's frame acts like robot legs. We split into two groups that were always up and down to mimic human footsteps. The sensors attached help control how the building moves forward. Trường Tiểu học Lagena was built in 1935. In September 2019, construction of the Sintian Di Thái Bình Dương Trade Centre project began, requiring the school to be moved to a new location. The Sintian Di Thái Bình Dương Trade Centre is expected to open in 2023. Earlier, in 2019, in Ha Môn city, a 30,000-tonne-long railway was moved 90 degrees from its old location. The outside of the building has been moved 288 meters. The main building has 5 floors, including 3 above ground and 2 underground, with a construction area of 22,800 square meters, and a total weight of over 30,000 tons, equivalent to nearly 200 Boeing aircraft. Engineers have applied motion technology to pull the drive-through to ensure stability when moving. This is the first project to apply this technology in the transfer of materials in China. The Guinness World Organization has recognized the transition project of the tramway station built by Hạ Môn, Phúc Kiến Province, Trung Quốc with a transition distance of 288.24 meters as the longest public transit of any architectural works. For small houses, moving is relatively easy. As you can see from the picture, the owner has asked all of his family to move the house to a new location, maybe even move the house by car. But the house was opened by the owner with a machine inside, a video was taken by a traveler back in Cander province, Central Cambodia. The method of leaving the buildings in general was not actually born in China, but whenever mentioning this work almost everyone also thinks of China first. China is a country with a very fast development rate and accordingly the country has also built many urban areas, cities and new architectural structures to suit the pace of modern living. However, city planning is not an easy task and sometimes the actual plan can change and be reoriented. However, many old architectural structures seem to be in places that are no longer in line with the new development directions, so demolishing and rebuilding some of the buildings is also understandable. But for the old buildings, the historic buildings, what will they do? The overall method of leaving will be a preferred choice. This method not only preserves the integrity of the building structure, but it also preserves its original appearance and its historical value. To make it easier to imagine, this method is essentially to lift an original architectural structure and drag it to a new location without causing any damage to that architectural structure. Around the world, engineers have successfully moved buildings up to tens of thousands of tons using modern technologies. Each project will have its own technical requirements, which need to be based on the initial design of that project to analyse the overall steps. The weight, the weight distribution of the work, the location and the size of the supporting material must be fully considered. From there, plan the installation process of the machine, the process of moving the project, to ensure that the construction process proceeds smoothly, to ensure the construction of the project. Before starting work, all electrical and water equipment must be disconnected. This is the job to ensure the safety of workers during the work process, to avoid unfortunate situations that occur during the work process. After completing the preparation steps, the workers use special industrial equipment to excavate the rock layer under the construction site, and at the same time temporarily install the support equipment. The supporting devices are installed in the correct position, the important positions responsible for the load of the work during the movement are strictly controlled. The size and location of the roofs are the determining factors in moving the house and moving it to a new location. The next step is to move up, which is a necessary step in the process of leaving home. The hydraulic equipment will be raised from the initial base, and the work will be raised until it is at a height suitable for the process. However, depending on the distance to the new location, the engineers will choose different departure methods. Typically, if the house and building are only a short distance away, engineers will use the wires. The wires are placed under the house, in the direction of departure, on the wires are arranged the cones, on the cones are placed a pair of théphiformes, linked into a wide tube called a diode tube. People move the house by means of hydraulic pushers placed on the floor or by using machines to pull the house by means of a cable. In case of having to move the house over a greater distance, people will use specialized loading systems. The road must also be paved carefully for a huge transport journey. Everything has to be very neat and exactly according to plan. A specialised loading system can be connected to each part and supported by hydraulic lines allowing the tank to be raised or lowered. It also allows the vehicle to remain in its original state when moving through uneven road sections. This will help the house not get damaged during transport. People put extra sheets of steel on the road so the car won't fall to the ground. The wheels used have a separate propulsion system to help them move more steadily, the work being completely unmounted during the process of leaving the house. Then, from there, move the project to a new platform location. Once you have left the house to the place you need to put it, the next thing is to put the house in the correct position you have previously determined. Take the false steps to build a new solid foundation. There are many reasons why people move to a building that is a historic architectural asset that needs preservation. There's simply no way you can leave. Leaving your house helps you save money, instead of having to build a new house. The building is often left to secure a firm foundation for the new building. Thank you for watching the video. See you in the next video of Hitech Amazing. Don't forget to share this video and click the subscribe button to support your channel.