Timber Framed Barn Part 20 More Purlins And Hydraulic Oil To The Face!

Nature house
149 followers
#NaturalHouse, #EcoHome, #SustainableLiving, #GreenArchitecture, #EcoFriendlyHome, #OrganicLiving, #NaturalLiving, #EarthFriendly, #EcoDesign, #HealthyHome, #GreenLiving, #SustainableHome, #NatureInspired, #EcoHouse, #EnvironmentallyFriendly
Hey everyone, so I got back from the waterwheel project yesterday
and that's finished now. So it's done, it's working as you've seen in the last video.
So it's time for me to carry on with this and it's going to be my focus now,
is finishing this barn. Because purling is the job to do.
Now I actually started doing some and some of the work on it about a month ago now,
maybe even more. But yeah, so the first part of this video you see is from a little while ago
and other than that we're going to be starting on this like full time.
I do have a set of purlings already made,
these are the ones that you're going to see me make in the first half of this,
first bit of this video. So there they're ready to go up.
These are for that side and so I'm going to finish off making the rest of those,
another three sets. It's really cold wind today.
Another three sets of them and then we'll get them installed.
And then I've got to figure out as well what I'm going to do with this big opening.
There's a really big span here to bridge and obviously I've got them as well.
So yeah, let's get to work.
So I've already shown this, making these before, although these are the other way around.
So the ones before stood upright, so that would have been the bottom, that would have been the top
and now these ones sit flat. This is the top, that's the bottom.
But principles the same, measurements the same, purlings, half lap purlings.
So yeah, just went out to go and check the geese and two of them got out.
Just as I realised they got out, I absolutely chucked it down
and they tried to take flight. So I'm absolutely soaked.
So yeah, it's lovely.
Hey everyone, so got those purlings done.
Oh wow, that's bright.
So I got those purlings done the other day during that big storm in the workshop.
Well, it was yesterday actually.
Today, the sun's out for the first time in, I mean, honestly, ages.
It's just rained every day for ages and ages.
So I'm going to get up onto the barn and get the purling notches in,
the housing joints, whatever you want to call them.
And we'll get that done today, make the most of the nice weather.
Right, so you might have noticed that these aren't equally spaced.
Had a bit of a change of plan with this.
I decided that this upstairs space isn't as usable as it could be
because you hit your head.
By about this point, you'd hit your head on these purlings.
So what I decided to do was on at least two of them, put like dormer windows.
In order to do that, I've put two purlings here,
two down there with a gap in between.
That gap in between will be a dormer window,
something like a dormer window at least.
And so that way, you'll be able to walk in to this area
without hitting your head on the purlings
and be able to get down to that edge, you know,
because you give a bit more headroom.
You might wonder why I didn't just make the whole thing up in the first place.
It was a design criteria to be able to mill everything on my sawmill.
If I wanted to get these all higher so I couldn't mill it on my sawmill,
I'd have to buy the timbers in.
So yeah, that's the reason.
Yeah, so that's why.
So I've got two up here, two down there.
You might wonder why I haven't just put one, say, up here,
and that's because we need it for the structural strength.
This is my sorry stockpile of purling timbers,
of which is two bits of scrap,
one that's got a rotten end on it,
one that's got a load of sapwood,
two decent ones, and some offcuts.
So I need to go do some milling.
So yeah, I'll make the most of this half-decent weather we got,
get some milling done,
and then what have I got?
I've got three more sets or two more sets for that section,
but then there's still another four sets for the other section.
But yeah, one job at a time, milling for today.
All right, so last couple of days in the workshop,
I managed to get another couple of sets done.
So the joinery is roughed out on these,
and they're ready to fit.
So we've got three sets there.
We need four, so we're going to make the last set.
And now I've got some timber to work with,
and then we'll get up there and fit them.
All right, everyone, you joined me in a very messy workshop.
So I've got my last four pieces of timber
that I need for that section,
so four sets of purlings.
And today I'm going to get the joinery done on them.
We've already gone through the planer.
They're all ready to go.
Still using this same drawing that Sam did ages ago.
Yeah, all the measurements still the same.
So we're just still running off that.
Right, last one for this section at least.
That's 40 of these made so far.
All right, let's get it done.
All right, that's that last set.
Well, last set for that section at least.
And you will not believe what just happened to me.
I just got a complete face full of hydraulic oil.
All this isn't water.
This is all oil.
I was just coming down with the tractor
to pick up those ones I just finished.
And I don't even know what happened
because I ran in just to eyewash my eyes out.
But hose definitely burnt blue as I was coming down.
I wasn't even lifting anything.
There it is, look.
That hose blew just there and it just scattered.
You can see it went straight into my face.
So you can see the pattern.
There it is all up there, look.
And that's exactly my head height.
So I was just sat there and the whole thing just went
and just hit me directly into the face.
You see it all over here, look.
That's all hydraulic oil.
All of that just absolutely blasted me.
And now I'm absolutely covered in oil.
My eyes sting even though I've eyewashed them
and I've got a blown hose.
Finished one job, one step forward
and then two steps back.
Oh, I can't believe how unlucky that was.
Look, there's the ear defenders I was wearing.
So you get an idea of how much oil came spraying at me
because they were on top of my head.
Yeah, that was not that fun.
Just washed my hair, washed my eyes out.
I'm all right.
But yeah, so annoyed.
I've been putting off that job
because it's really repetitive
and I've just been like, ah, really boring job.
Right, let's get it done.
Push on, finish the last piece.
Just come down just to move them.
So I think, great, finished a job there.
I'll do that, get the workshop tidied up.
Bang, didn't even know what hit me.
Took me a few seconds to even process what happened.
Yeah, not fun.
I'm just glad it wasn't hot.
I'd only just started it.
Well, I was hoping to get these purlins fitted today
but it is not a pleasant day, as you can see.
And I've got this tractor stuck here now.
So I need to sort this out.
You probably can't see a lot
because we're in a storm.
We've basically had a storm.
I've had about three this week so far.
At least I know there's no pressure in here.
Because there's a hole in it.
Going to get one of them made.
It's going to be 50 quid probably.
Weather like this, it's why I don't really plan
on doing too much building this time of year.
I'll do a bit of the hydro stuff and other things
because we just get these storms
and you can't plan around it.
It's just, you can't really work in this.
I just can't bring myself to work up there at the minute.
We're getting 40, 50 mile an hour gusts.
And yeah, it just doesn't look that appealing.
So I'm just going to fix this tractor.
All right, we've got a dry day at last.
I've got my hose changed.
Hopefully that won't shoot me in the face again.
I've got the tractor moved and it had a flat tyre.
So I've got to change that as well now.
But never mind, because I can get on
and work on the barn today, which I'm happy about.
Slightly lighter than the middle ones.
There we go.
Tappity tap tap.
That, is there a gap under there at all?
A little bit.
Yeah, not too bad.
Might pull down with the fixing.
That's all right, isn't it?
Happy with that.
Oh, I didn't just break that, did I?
Not having much luck here.
If you saw that end of the mallet came off,
my hand kept going, smashed my thumb into the bit of wood.
It's all right.
I thought it was broken initially.
Oh, I'm not having much luck.
I'll get there.
Trying to pull out the other end now.
Quite a good fit.
That's gone.
Morning, everyone.
So not great weather, rained all night.
But I think it's workable in.
You know, when I was building this roundhouse down here,
it's quite a bit more sheltered.
And even though, you know, it was really wet
when I was doing it and muddy, and it was really grim,
it didn't have the wind associated with the barn.
The barn's in a more elevated position.
And obviously when there's a wind,
even a little bit of rain gets you soaked.
Because that's why I'm trying to work on it in good weather.
And today definitely isn't that.
But it's better than it could be this time of year.
So yesterday I finished getting these two rows fixed up.
All bolted in from the top.
Same as the other ones, really.
So now we've got two more rows to try and get done today.
Across here.
And then there's joists that bridge between them.
But that's for another video, I think.
Right.
Yeah, they're a good 50 or 60 kilos, these timbers.
It's like lifting a small person up three meters.
It's not easy.
So if I'm grunting and groaning, that's the reason.
It's also wet, windy and slippery.
If you've never dealt with green timber,
it's a lot heavier.
Twice as heavy as the stuff you buy in the shops, generally.
And this is larch, which is a very dense wood.
Still a softwood, but it's a very dense softwood.
I feel like I'm not that fit at the minute, either.
Let's have it knocked over.
Bottomed up.
That ain't a bad fit.
Fixing to screw that down.
Yeah, happy with that.
Oh, that's a good fit.
That is going to be nice.
There it is.
We're bouncing on there.
Just had a slight twist to it, that one.
So it was pulling the joint apart and bouncing.
But once it's got a fix in it, I mean, it's literally perfect.
Pretty happy with that.
Look at this weather, look.
Can you see that mist just blowing across?
It looks beautiful, but it's challenging to work in.
Let's get out of this weather.
This is grim now.
OK, so that is going to conclude this video.
Not a huge amount of progress, but for this time of year,
I'm happy with it, really, getting them done.
It's a good job done.
And there is, although it doesn't look like a huge amount,
there is a huge amount of work in those.
Still got more of them to do for the lean-to,
but that is mostly done now.
So I'm happy with that.
I've got a process for it.
So I've got a bit more milling,
and there's not as much to do on that section
because it's got that open span,
which cuts out one whole set of them.
So, yeah, we won't be too long now.
We'll be putting up rafters
and things will happen a little bit quicker.
Yeah, I've been a bit hard done by in this video, really.
I've had oil chucked to my face.
I've hit my thumb.
We've had bad weather,
but I am pleased to be back doing it.
If I'm moaning, I do know how lucky I am
to be doing the thing I love to do.
Just this time of year, it can be pretty challenging
doing the heavy work like that in that weather on your own,
especially if you have an accident.
Yeah, next video will hopefully be a bit more positive,
less hurting yourself,
and we'll get a bit more progress.
All right, I hope you enjoyed the video
and thanks for watching.
