How to remove A Well pump

Full House
57 followers
Feb 16, 2025
Comments are disabled for this video.
Well, today on the show, we got no poo poo butter water.
We're gonna show you how to definitively check
your well system at your home and get your water running.
Hopefully give you a little bit of instruction
so you don't have to get any equipment out
and do it yourself at home
because if anyone else can do it, you can do it too.
And during this process,
I figured out a way to do this
without using any equipment.
Super simple, super cheap,
and I'm gonna keep about two to $3,000
in your pocket, promise you.
First off, I took about four days
to make this video and stuff, so it took me a while.
For you, hopefully we have you fixed up in 10 minutes,
but if we don't, well, I've got solutions for you.
You're gonna need a little bit of water,
so you can go to a neighbor.
They'll possibly loan you some.
You can fill up some gallon jugs.
If that's not a possibility at Wally World,
the water was 39 cents a gallon.
Adds up to about five bucks
when you need 10 or 12 gallons of it,
and you can use that water to flush your toilet.
All you do is take the tank top off of our toilet
and dump in a gallon of water.
That'll allow us to flush it
until we actually get this resolved.
First part of the video,
we're gonna go through and check some stuff.
Should take you about 10 minutes to do it,
even if you don't know anything,
just like me before I started doing this.
If you live in the country like I do,
more than likely you have an underground well system.
It could range anywhere from 25 feet
to 500 feet down under the ground.
You're like, how do I check that out?
Well, it's actually pretty simple.
Somewhere in your home,
you're gonna have a control system for your water inlet.
Most well and septic systems
are gonna have a mechanical area such as this one.
The most common problem with wells and pumps
is this pressure switch.
Water flows in through the back of here.
When the water pressure is too low,
according to your gauge right there,
these little points come together
and they allow electrical current
to travel from your electrical box out to your well
and build up pressure.
My situation, I used to be able to come down here,
taking the gauge hammer I could possibly find
and tap on this.
And then it would trigger my pump to come on.
So I've known that my pump is gonna have trouble
for quite some time.
When that happens, this means you need a new switch.
You can go to any local hardware store.
They're gonna have these for about 30, $35.
When you tap on that switch,
you're gonna see the little points click up and down.
And if there wasn't any lighting in there,
you might see it flicker a little bit of light
from making the electrical connection.
If you noticed in my situation,
the points were pushed together,
which means that my pump is requesting to come on
and my pressure switch is actually working.
When the system's operating and functioning correctly,
it should have anywhere between 50 to 75 pounds
of water pressure.
I'm not a certified electrician,
but make sure you turn off the electrical power
before opening any boxes.
Most boxes won't allow you to open them
without turning off the power.
Now I wanna make sure that there's power
going out to my switch.
So I turn the power back on and carefully check
to make sure that there's voltage
on the other end of my fuses.
We got power there.
We've got power going through our switch.
Now keep in mind that there's an input power
and an output power.
So all four of these legs need to have power
when the pump is not pressurized.
Because the pump is requesting that it sends water
to the back of the pressure switch,
this is not a good thing.
If the pressure was there, switches should be off
and it shouldn't be requesting water.
If it is, you're using a lot of electricity unnecessarily.
Now some of you aren't gonna have electronics like mine.
You're gonna have an electrical box like this
with a capacitor inside it.
These capacitors can go bad.
I'm gonna put a link to this gentleman's video
down in the description below so you can look this up.
But if your capacitor's bad,
that can also cause you to not have power at your switch.
While I was editing this video,
somebody told me how awesome I am,
so I had to leave it in there.
Let's say you have a capacitor
and you know how if it's bad or not.
You can tell by looking at it sometimes.
So if we take a look at the one on the left of the screen,
it's not blown.
Then if we take a look at the one
on the right of the screen, it's blown.
The little nipple is pushed out.
Highly recommended, something I learned
after I actually repaired this problem.
If you're gonna end up changing your well pump,
make sure you drain out your system as thorough as possible.
I would even recommend kind of vacuuming it out
because the water's gonna drop down
onto your torque arrestor inside your well,
and then it's gonna make it hard as hell
to pull the frick up.
This is your bladder tank.
It helps evenly and proportionately
let water flow through your house.
Inside the tank, there's a rubber bladder
that's surrounded by air pressure.
That air pressure pushes against the rubber bladder.
The rubber bladder pushes against the water,
keeping even pressure throughout your pipes.
It is simply filled by a little Schrader valve
that is at the top of it, where you just put in
by your air compressor out in your garage.
Now we need to go out and check for power at our home.
For that, I may need my girl tools.
Now when looking for your well outside your home,
you're gonna find a well that looks like this,
maybe with the pipe coming out the top,
or possibly one that has a teardrop cover
over the top of it with three bolts of fixing it down.
In either situation, they're gonna function
exactly the same with the exception of the pipe
is gonna either run above ground,
going back down into the ground
because of lazy people not installing the well properly,
or the climate where you live at in your area.
When you go to do this, if you have one like this,
please cut it right here.
Do not cut it up at the top of there
because you won't be able to affix the pipe properly.
It'll make it much simpler.
On the top of here, there's gonna be four bolts.
You don't need to take the nuts all the way off.
You just wanna loosen them up.
And that's because this works as a crush.
The top is hard plastic, the bottom is hard plastic,
and the center is rubber, and it expands out
as you tighten the nuts up.
No matter which system you have, one like this one,
or one like the one that we're gonna be working on
in this video, pump removal will work the same.
Now I came out here, I found my well.
This is where my pump is.
My pump is a long cylinder that drops down inside this tube,
and it can be hundreds of feet down.
I'm gonna make sure that it actually has power going to it.
And I definitely have power going to it.
Now I wanna listen and see if I can hear my pump.
Can't because it's not working.
So now I need to pull the pump.
You can do this yourself.
It's not gonna be very much fun.
In this video, I wanted to cover all the bases
for people who know things
and for people who don't know things.
The trick that I'm gonna use to pull this pump out
is simple, practical, and it's something you can do
without a heavy piece of equipment.
I'm gonna keep thousands of dollars in your pocket,
so please, if you're looking for a particular space
in this video, please turn the volume down,
restart the video, and let the thing play.
I greatly appreciate it.
Now, you can't break what's already broken,
so my hope is that I don't break the pipe as I pull it up.
That's a fear, but if it's gonna break on me,
it's probably gonna break on somebody else.
So regardless, ultimately,
it's gonna be the same result either way.
So I've got a tool that we're gonna make.
Super simple, super cheap, and super quick
to pull this pump out of here.
Something to consider when you're thinking
about doing this is it costs $1,700, $3,000
trying to charge you.
That's what you're getting paid to do it,
and trust me, I've never done this before,
and I can do it, so I know you can do it.
If you got a question for me,
you can reach out to me on Clay's AC and Auto Repair.
I answer them for absolutely free.
I can't help you with baby mama drama,
but in this case, I may be able to help you with your well.
Normally, it's automobiles.
Don't be the next to them, be the first to you,
and if anyone else can do it, you can do it too.
Now, you're not always gonna see this pipe
at the top of here.
Sometimes, this is gonna be down in the ground
to where your service outlet goes to your house.
So if you don't have a pipe like that,
you're gonna have to go to the hardware store
and pick up a little bit over four foot of pipe,
put it together, and run it down there
and screw it into your pitless fitting.
You'll understand, and I'll show you exactly what I mean
here in a few moments in the video.
Now, we can see that the direction of flow
from our pump is this way
and goes into our house like that.
Normally, on the reverse side of your cap,
a good installation would have it written down
how deep it is, what size horse motors in there,
and everything else.
Mine don't.
It's important to know how deep your well is
so you know what kind of motor that you're gonna need
once you get it pulled up.
Pulling up the motor's the hardest part,
so we can call the local health department
or check on our paperwork we got when we bought our house.
It'll tell us how deep that well is.
Double-check these wires again,
make sure I ain't got any power from there.
Now, if you were able to see down inside there,
you're gonna see this little arm or shoe right here.
At the top of it, there's a half-inch little screw
in the center of there that we need to unscrew
that releases the arm that allows you
to drag that thing back up out of there.
What I need to do is I need to loosen up
my shoe or pitless fitting.
So what I've done is I've taken a 12-millimeter socket,
I cut it kinda shoddily, and I put it on about
four and a half feet of extension.
I do recommend that you take an electrical tape
your extensions together so they don't actually fall off.
Not that it's gonna go anywhere,
but it's gonna create a big problem.
To loosen up that shoe before I had to pull up the pipe,
the funny thing about that is,
at this time, I didn't know that.
So I didn't do that before I tried to pull it up there,
and it's got this bracket that drags up on the well.
We're gonna see if it broke or not.
Big problems ahead.
Now, I've heard guys in the video talk,
in other videos talk about how these are 3 1⁄4 inch.
In my situation, this is definitely one inch.
Now, I think hindsight being 20-20,
I wish I had gotten an extra two-foot piece of this
so it would be up a little bit higher
to be able to pull it up out of there,
but I think I'll be fine.
So I've grabbed a one-inch three-way,
and I'm gonna screw all this together
without dropping it off there.
Now we've got that all set on there,
we just need to get us some fine Bureau Young's men
to pull this thing out.
Well, I went inside and I grabbed a little bam-bam here
with his big old meaty arms.
Tried to have him go out here,
and we tried to pull up straight on this pipe,
but yeah, he's not able to do anything,
so we're gonna need to do something differently.
So I got another one.
Come on, man.
So then these two guys tried,
and then we got two more guys.
No good.
Oh, it's definitely not.
Dude, I could've screwed it.
Remember when I was in the basement and I said,
hey, turn this valve on, drain that water out?
Well, if you don't do that, you're gonna struggle.
Water is gonna come out of the shoe once you loosen it up.
Then it's gonna drop down onto the torque arrester
at the bottom, creating a suction,
which is gonna make it very, very difficult to pull this up.
Chain hooked up there,
we're gonna try to pull this thing up.
We've got two things going on here.
One, there's water down on top of the torque arrester.
Two, we didn't know that the shoe had a half-inch screw
that needed to loosen, so it would release the shoe
down there.
Definitely got some pressure on it.
The little beefcakes definitely wouldn't have been able
to pull this sucker out.
Now, the idea is you wanna pick it up straight and square,
so make sure when you're pulling this,
you're pulling it up straight.
Let it loose, and started picking it back up again,
and it came up even further.
It's coming up out of there now.
I keep loosening it up a little bit
and letting it sit over there,
because we're getting a little bit kiddywampus.
I keep pressure on it.
Now I can hear air and stuff down inside the tube.
So it's slowly creeping its way up.
Obviously, this is really tight right here.
Well, I broke the seal without loosening the screw.
That's not a good thing.
We'll see.
It seems to help when I let it loose a little bit.
I think it just broke loose.
Seems to be coming up pretty easy,
so hopefully we'll be able to pull this sucker
up out of here.
I'll have to unhook these chains
and try to pull this thing up.
This is definitely not easy.
We've got it up a bit.
I think the craziest part about all of it
is this was just laying in there.
Oh!
It was a bit of a struggle,
but we did get it up to the shoe right here.
And as we can tell right here,
this screw turns that little lever
that presses it up against the other side of the pipe
and locks the shoe down to the side.
There is a gasket that goes on here.
Mine fell down on my torque arrestor,
but we're gonna put that back on
when we go to reinstall it.
Here's what made this job super simple.
I went down and bought two pairs
of these vice grips at Harbor Freight.
These chain vice grips worked perfect.
I didn't even need pipe wrenches for this situation
because I had these.
Buying two of these is gonna show you
how it allowed me to pull this pipe up out of here
without machinery, even though I use it.
With the utilization of these vice grips
and a little bit of ingenuity,
you could have got this thing out of here
without a cherry picker or a piece of heavy equipment
like I'm gonna use later in the video.
Basically, you could have took an adjustable rear hitch,
put it in the back of your truck,
put a two inch or three inch square tube in there,
hooked up a boat strap that will ratchet your boat
up onto the trailer,
then used that along with the vice grips
to winch this thing out of here.
It would have been super awesome.
Drilled some holes in the straight piece of pipe,
mounted the winch on the opposite side,
then put a pulley on the top of the pipe
and used this method that I'm using here
to pull this pipe right out of there
and you would have probably been done
for less than a hundred bucks,
along with your parts, of course.
So what you're gonna do is you're gonna wrap
the chain vice grips around there, both pairs,
putting your chain in between the two pairs of vice grips,
allowing you to move one down as the other one picks it up.
Then you can lock it at the bottom,
lower your top one down and man,
you're gonna be done in a snap.
Called our health department
to find out how deep this well was.
We thought we were gonna be on this job
for like three, four hours pulling this pipe up.
We soon realized that the pipe was pretty shallow,
only about 60 feet down.
And we did also realize that if we would have used
this method on even a deeper well,
we would have probably had it out in an hour
because this only took 20 minutes.
Yeah, I was really surprised that the PVC didn't break,
but it doesn't.
Okay, I got it clamped.
Man, I think we should unscrew these unions.
What the hell are you gonna do?
Well, I mean, I guess it's got a point there, I suppose.
Back up.
I'm gonna go back once I get $2,000 in my Irish ass.
Well, then there's this guy, I'm gonna dump him.
You're gonna go with the cherry picker in an hour.
Yeah, probably so.
All right, now you try to hold it, Jesse,
when it comes out of there and let's see what happens.
Go ahead, come up.
Oh, that ain't the pump.
Well, maybe it is.
It ain't very deep.
Oh, there's the pumpy pump.
Ready?
It's gonna go boing?
We don't know.
I'm standing back, if it does,
I'm maxed out.
So I wrapped my chain vise grips around my old pump
because you can't really hurt it, it's already broken.
There it is.
Nice, nice boy!
Okay, so we have a pipe connecting to our shoe,
which is how water gets into our house
as the pump pumps it up there.
We also have a gasket that goes on the outside of here.
Then we got our pitless arm here.
Down further on our pipe, we're gonna have a check ball.
These pipes are made of one and one quarter inch,
either PVC or like a black pipe,
just depends on what they installed it with.
Either one's gonna be fine.
We're gonna be reusing our PVC
and we're gonna be replacing this check ball right here.
Obviously there's a flow arrow on here,
allowing water to come up this way,
but not travel back down this way.
Near the end of the pump,
we're gonna have what's called a torque bracket.
This bracket allows the pump not to sit inside the tube
and move every time it gets switched on and switched off.
Our wires run through that pump and that torque bracket.
To remove the pump from the pipe,
make sure you have a good grasp on your PVC tube
and you're gonna spin it counterclockwise.
It doesn't hurt to put the vise grips in the center
of your pump right there, because well, it's no good.
Think you wanna be careful,
make sure you have a helper for this, even though I didn't,
then you don't ruin the threads on your PVC pipe.
You're gonna notice that my pipe is much larger
than my original pipe.
My original pump was a half horse.
My new pump is a one horse.
Look at the guide.
It'll show you what you can do.
I'm not doing anything overkill.
I'm just adding more pump.
So hopefully I get more pressure inside the house,
which will give me more pump in Clay's boom boom room,
where I take showers.
So now I'm gonna replace my check valve.
This can decrease the performance of your pump
and decrease its longevity.
So make sure you replace it when you're taking this out.
This does absolutely nothing.
Whenever you're installing Teflon tape,
put it on the same direction you're gonna be turning.
So in this situation, we would install it clockwise.
Your Teflon tape should be tight enough
to where you can see the threads.
I usually go around four to five times.
So I've got a total of four wires
that I wanna push through here.
Three of them are electrical wires,
and one of them is a safety wire.
So I'm gonna drill a hole through here.
I have four holes so I can push my wires through.
I've got my wires pushed through there.
I even zip tied them so they don't pull backwards.
If you're looking for a guide
on how to repair these cut wires,
you can refer to the video
that I'll link up in the top right now,
or you can check the video description.
Okay, so now I've got some safety line,
and that's the reason that I wanted a total of four holes
so I could run the safety line down
and attach it to my pump,
just in case I ever break the PVC.
I wanna be able to get this pump out of there
because even getting a pump out only 60, 70 feet down
would not be fun,
but I couldn't imagine breaking one that's 500 feet down.
Well, I'm gonna take the end of it,
run it through here,
use a little clamp to hold it together.
I recommend stainless steel,
but they didn't have that at my hardware store,
so I just picked this up.
It'll be fine.
Hopefully over time it holds it for the next 15, 20 years.
At least I hope that's how long
before I have to change this thing again.
At least the next person can thank me for doing this,
even though I devised the super awesome way
of getting it out,
this should work pretty well.
So now we wanna go down and make sure
that about every five to 10 feet or so
we put electrical tape around the pipe.
Keep this loose-ish,
so when it torques,
it can move and it don't break the wires.
Now at the top of the pipe,
we're gonna hook up the vice grips here,
the boys are gonna grab this
and put it down inside the hole there.
They like putting big long pipes and shafts together.
Deep shafts.
You grab the heavy end.
Try not to damage my wires, okay?
He's having a hard time finding the hole.
That's why he ain't got any kids,
but we don't want him to multiply anyway.
Oh wait, hold on, I forgot about the safety wire here.
I'm gonna have to undo that.
What'd you say?
We're gonna need to lube up the edges.
You need me to lube up the edges?
Yeah.
Yeah, all right.
Huh, that's a problem I didn't foresee.
Maybe if Cameron brought it straight.
Cameron, bring that up a little bit.
Walk up the pipe.
See if standing it up straight kind of helps at all.
There it goes.
Wonder what all that stuff was
that just fell inside there.
Did you hear that?
That probably should not do that.
So you gotta make sure it's square
and then give some pressure to push it down.
That's a really cool sound.
Then it'll rest on the vise grips right there
and we can Teflon tape or other pipe, put it on there.
Now at the other end of the pipe,
you wanna make sure that you put some,
your chain vise grips on here, lock it down.
Well, this is gonna be like a little chimpanzee
******* a Bronco getting this started,
but we're gonna see how it turns out.
Yeah, this is not gonna be easy at all.
Maybe I should get a step ladder.
Maybe we should have put it in there as one piece.
We might have to pull it out and put it in there.
Okay, turn the ladder around the other way
so you can get up as high to the end.
There you go.
So we've got a truck.
We're gonna stand up.
That'll give us more height
to be able to keep that pipe straighter
to hopefully get it started screwing in.
But worst case scenario, in my scenario,
I could just pull the pipe out
and that would work just fine.
Was a little bit of a struggle.
Made sure we pushed it into the ground.
Then we're able to pick it up straight.
Got her started in there.
Now, once we get it up to the top,
once we move it down and we get it up to the top,
we can actually tighten this pipe up against here.
We put three lines of Teflon tape on the pipe there.
Now we can let this go.
You boys got it?
Get that out of the way.
And then the boys can start dropping it down.
Now, every five feet or so,
we wanna put some tape on here
to hold the wire up against it.
Ooh, that's what she sounds like.
No, don't drop that down.
Yeah, no.
Now we'll attach the other part.
It sounds like she's blown all out and everything.
Once we get it to the spot,
we wanna make sure that this does this,
that this is pointed in the right direction.
We also need to make sure that our gas gets on it.
Now that fits on there pretty tight.
There's a flat edge that you wanna make sure
is rolled into the proper position.
You'll pretty much know that this is on there correctly,
and it doesn't wanna just easily fall off.
It should conform to about the same pipe here.
Now I'm gonna put a bunch of grease on this.
I don't know if that's gonna help,
but it seems to make sense to me.
I don't know if they sell these gaskets.
I didn't see any anywhere,
but you can replace it if you have a little cut like that.
I'm not gonna do that, but you might.
They also have this type style shoe fitting.
I wish I had this one
because it would have made it a lot easier to line up
than what it was to line up for me,
but I got a solution for that problem too.
Now we've got our pipe started in there.
We do not have it tightened down.
We just turned it in there three or four turns,
and we're gonna take our vise grips off, lower it down.
All right, so we're gonna turn this on,
make sure our pump works.
Go ahead and tell him to turn it on.
Nice, dirty water.
Turn it off.
Okay, so we're gonna release our chain right here,
and then drop it into place, and let it down.
We're gonna make sure that this wire does not,
stays on the side of there.
Grab some of that electrical tape.
Let's electrical tape the wire to,
it's right there on the top of that red toolbox over there.
There you go.
Now, lower it down.
It hung up again.
Let's try it one more time.
All right, it must be too far out.
Should go down to where it pretty much bottoms out.
Now we take and tighten this up.
We're gonna take the 12 millimeter tool
I made earlier in the video, and drive down the shoe screw.
Now we're gonna go inside, turn the water on,
and see if it's leaking down inside the tube.
Tell him to turn it on when he's ready.
Oh, we got a massive leak.
All right.
Apparently, that's how you check
to see if you have a real bad leak.
Okay, so we've got a really long bore scope.
It'll be down in the description, Amazon link to it.
If it's worth a piece of poo poo.
I've read some bad reviews on it,
and I don't wanna be throwing out somebody's name out there
and it's a piece of turd.
So we're gonna try this out.
We've got it stuck down in a pipe.
See what happens.
So we've got our pipe inserted down there.
We've got our bore scope down there.
It's obvious that we're not tightened up against the pipe.
Plus we're probably not clocked a little bit.
We're a tiny bit off.
Hopefully before you removed your pipe,
you marked it so you knew approximately
where your junction was.
It's kind of hard to tell,
but now we've got it clocked a little bit better.
Now we need to tighten up our pipe
and push it up against the sidewall of the well.
Now we take our tool we made,
drop it down inside there and tighten this thing up.
You can see right down in there.
Barely see the top of it.
I know it's hazy to you folks,
but we can see it pretty well.
Hopefully we got this set just about right.
Now I'm back here at my well switch.
I've turned my power off to my electrical box.
I want to make sure that my system does not leak down.
So what I need to do is I need to leave this off
for a little while.
Obviously I don't hear it dripping down inside the well,
but just to be safe, I want to double check everything.
It's on, it's on, there's no leaking.
All right, so we have maximum pressure.
We don't hear any leaking of water down there.
So that's really good.
And we know that the pressure's holding.
So you can turn off your pump again.
Don't run anything for an hour or so just to double check.
You know, flush your poo-poo butter down the drain
because if you've been like me
and you've had a couple of days,
you've definitely got poo-poo butter inside your toilets.
Then that way that'll allow you to actually check
and make sure your system is completely intact
and you don't have any leaks down there by your shoe.
Man, that was a tremendous amount of work,
but how accomplished do you feel?
I felt great.
I love doing new things that I've never done before.
I especially love paying myself two grand
to not pay somebody else,
but I didn't have two grand to pay somebody else anyway.
So it really didn't matter.
Kind of stuck with myself.
If this video was helpful, please consider subscribing,
clicking the notifications, sharing my videos,
sending me them sweet old thumbs up,
commenting down below because it helps the video go.
Remember, don't be the next to them.
Be the absolute first of you.
And no matter what it is in life
you think you can or cannot do,
if anyone else can do it, you can do it too.
God bless, folks.
Have the greatest of days.
