Timber Framed Barn Part 10 Cross Frame One Complete

Nature house
149 followers
#NaturalHouse, #EcoHome, #SustainableLiving, #GreenArchitecture, #EcoFriendlyHome, #OrganicLiving, #NaturalLiving, #EarthFriendly, #EcoDesign, #HealthyHome, #GreenLiving, #SustainableHome, #NatureInspired, #EcoHouse, #EnvironmentallyFriendly
Morning everyone, so it's the start of a new week of framing in the barn. I thought I'd just show
you around here quickly because I haven't done any filming around here because we're away in the barn.
So I thought I'd show you the lambs and stuff. I've also taken down the temporary structure,
temporary building. I did that last weekend. I didn't film it, I just knocked it down.
So I'll show you that as well. Yeah, just show you a bit around and then we'll go over to the
barn for another week of framing. While I'm on the way over there in the video I shall put up
the CAD model just so you can see what we're working on. When it's all laid flat it's kind
of difficult to tell what's going on. So we'll have a look at the CAD model and then it's another
week of timber framing. So yeah, temporary building's down. Managed to pull that down.
A bit of time wasted but you know all the materials are still there ready to use. They're
you. Gave birth to this beautiful lamb, didn't you? Lovely big lamb. It's so big we did have to
give a bit of assistance. But you are a lovely lamb, aren't you? You lamb. So I think she's a
keeper. I think we're going to keep her. You're beautiful, aren't you? Good mum.
So yeah, once the weather improves they'll be out on a bit of ground but look what it's like
at the minute. Got three more sheep in here waiting to lamb. Don't think that one's in lamb.
I think we should get two more. Hopefully. They're about to go and land in my pond.
Canadian geese. There you go. They just landed. Yeah I thought I'd quickly show you the wood
situation. We're running out of timbers. We haven't got enough to finish yet
and this is what I've got left to mill. It's just a muddy sloppy wintry puddle.
I've got that but it's all too small and twisted or ring shook and all of the timbers that are
milled are already down the barn. So I'm going to run out. So I've got another load of wood coming.
That's going to be to finish it. I've got to do more purlings, got to do posts,
a few more posts, a few more mid rails, a few more truss timbers and then all the cladding,
the stud walling, all that kind of good stuff. So there's a lot of timber left to mill.
It's because everything's gone from here other than the purlings.
Let's go over to the barn and get this framing done. Probably got like two weeks left of framing,
something like that. See a little bit more framing videos and then I'm gonna have a little
bit of a break from framing to do a bit of milling and stuff to get prepared for some
floor beam timbers and stuff like that and then we'll put the frame up and try and get the roof
on and stuff and then after that I've got this really cool hydroelectric project booked in.
Going to be doing a water wheel for an old mill. I've got the CAD model, it's all designed and
everything ready to go so we're going to be doing that as well. So that'll be a bit of a break from
building then and then once that's done I'm going to get back onto the barn to try and get a bit of
cladding done, maybe the top flooring and stuff like that. So yeah we're going to be really busy
but for this week and the week after I just need to concentrate on getting that frame done
and so it's just back and forth to the barn and then there's just gonna be a lot more milling.
So yeah but I thought it'd be nice just seeing as we're basically entirely just filming away
from here I thought it'd be nice to just show a little bit around the place and have a little
catch up. Yeah over to the barn and time for another week of framing. So I thought we'd quickly
just go over the model while we're on our way over to the barn. So in the first video we did
this wall frame here with the mortise and tenon mid rail, the short side that's up on the higher
plinth. In the second video we did wall frame two and wall frame three that go from ground all the
way to the top and in this video we're going to do a cross frame so it's this cross section.
We're not going to do this part we're going to do this part separately or maybe not even at the barn
I might do that here and we're not going to put this part on because there's no need to because
it's just bird's mouth like a roof timber in. So we're going to do the truss here
make all the beaks that attach it to the wall plate and all of these floor joist timbers there's
an interesting bit of joinery going on in here which we'll see and the braces so we've got five
of those to do now so hopefully just another week or two's framing and we'll be at a position where
we can leave the barn and come back here and do the rest of it on site maybe even get the thing up.
All right good morning everyone it's a damp and miserable Monday bank holiday Monday morning
we've got a bit of a skeleton crew here today just me Howard and I
we've just packed away the other wall frames that we did and we're just starting to
figure out what we can do the cross frames.
So the cross frame work has started so we've got it laid out yesterday I was a bit slack with
filming yesterday but Steve's about to start cutting out tenons for them Howard is on the
mortises. Howard what's the type of mortise called that we're doing with the slanted face?
What do you call it? Squinted shoulder or something along those lines. Essentially
with timber framing if you just have a tenon going into a mortise you end up
with your bearing point only doing the tenon so with this with this little step the timber's
actually sitting on this whole diameter but then if you take that whole diameter all the way up to
the top you end up with this failure point where you've interrupted the grain so they go from a
step down to nothing and so that's still got the step that you're taking the minimal amount of
wood out so that's what we're doing here because this is a floor and it's load bearing it's got
this step so here's an example of it now Howard's just started cutting this one out.
So we've been having a bit of a pontificate about this joining here
pontification and because we're chopping a bit out with these what are we calling them?
Howes squinted joinery so we're cutting a bit out of the post
and as a result we actually changed it so they're not just going to be tenoned in there
we're going to put them on a spline so this is going to go all the way through there and then
the two floor timbers are going to rest on it so this becomes their tenon then and then the
weight of them sits mostly on these shoulders. So that's that ledge that the floor timber's
going to sit on. What are you up to then Nye? I'm doing the datum lines on the PR
and other pieces for the truss layout. So yeah so he's working on putting these centre lines
datum lines for this truss so Howard's currently working on this joint here with that squinted
step joint and then there's going to be that piece of oak between there acting as a spline
and Steve's working on this piece here and I am making braces again and filming.
What's that you're cutting out Steve? This is for the spline, the oak spline going in here
through the post and into the next beam as well. So that spline's going to go all the way through
there that Howard's just cut out and into that slot that Steve's working on and then the weight
of the timber will sit on this edge or the weight of the floor rather. So that's that angled shoulder
so not only do we have this really thick floor beam it's 250mm but because this is now at an
angle it also means it's got a longer shoulder which helps with racking.
clash situation here so the brace the bottom of the brace comes to here somewhere and it was
going to clash with this mortise so we stepped the mortise and then we put a haunch on the tenon
so essentially like when you're doing a door just to locate a haunch. It's a bit of an interesting
one for a timber frame, a bit unusual but it gets us around this problem of taking the material out
from under the brace. Right so that's the last of the braces needed for this cross frame.
Just stacking them up here because it's the most out of the way place and closest to where we're
going to need them because we're going to want them after lunch basically. There we go, just about.
So Steve and Howard have just been squaring all this off and getting all the trigonometry right
so now that's all set they can see how the joints are sitting
and they're sitting pretty good as you can see. I've just finished making the last brace
that we need for this section and so now it's lunch and then we'll probably
start fitting braces up to these. Just about to leave for another day at the barn and we've got a
ewe who's imminent. She's showing all the characteristics of a sheep that's about to
give birth. She's stepping around, she's agitated, she's putting her nose up in the air and she's
got a bit of snot hanging off her tail so I think her water's broken. So yeah, it's your little
lambing lookout is it dear? Sitting with your mates, with your lambing lookout. All right,
can I join you? Is that for me? Oh did you see it come out? Well there was more drippy stuff coming
You can't see, I've got a view from here. It's better than the cinema isn't it?
Better company. I don't want to get too close to spook her or anything but we've got contractions
see that? Hopefully she does it all on her own because it sets them back a bit if you have to
go and help out. Right, unfortunately I'm gonna have to go and intervene because she's been about
half an hour pushing, she can't get it out. You can see the back, two back legs but she can't
squeeze the head out so I'm gonna go and help but I shan't film it because I'll probably get banned
from the video or something for gruesomeness. So yeah, see when the little lamb's out. It's a
pretty good bit of action just before going and working on the timber framing. So I had to pull
the little lamb out, beautiful little lamb. But it's all going off this morning, got geese in the
pond, geese everywhere, lambing. They're just trying to get off to work. Beautiful little lamb
up on its feet. What was that? 10 minutes, not even? Up on its feet, gonna have a suckle in a minute.
Hopefully there's no more in there but she's got a huge bag of milk there
and the afterbirth is coming out so yeah what a beautiful little lamb, little you lamb.
So she might be a keeper that one, actually quite a big lamb really.
Yeah good mum. Right that was a bit of excitement before work so yeah off to the barn timber framing.
We're in the middle of a bit of a storm here in Wales at the moment
and so it's really dark in here unfortunately today.
I've ended up doing all the braces because I've done other stuff as well as you've seen in the
videos but it just works out well with me having to keep an eye on everything that needs filming
and keep going over the model and the plans and stuff. The braces is something I can dip
in and out of without slowing anyone down. Right, brace time. Little braces, they look
like lovely braces, I wonder who did them?
Nice, swing this end out.
Poor Nye's having to do it on his own because I'm trying to film it. Sorry Nye.
First fit up to go into plan, a few little tweaks, won't be long though, what are you up to Steve?
So I'm marking the principal rafters to fit on the first truss. These will be the tenons right?
Yeah that's right, this is the top into the king post here and then we'll be scribing the
colour down to where they'll meet the posts. Cool, so do those get squared off across there?
Yeah they'll get squared off again just at that point.
There is something going on with that.
Right hey everyone, new day and yesterday we got all these braces and everything cut out
and in place and the boys got the truss done, Steve and Nye were working on that
and we just laid it over because there's another couple of braces got on that,
get a better view for you. So me and Nye are just getting some timbers ready to start the next truss
and then once you've got all these two braces cut out and these little beak cuts cut, then this
frame will be packed away then and we'll start another frame today because this won't take long
So we're just figuring out some beak cuts at the ends of these, how we're going to house them in
the top plate and putting on the purlins, that's what we should do for the beaks and how they
house into the top plate. So now we're just going to add on the purlin measurements. Yeah so that
one and then the next one is 1020 from that face, so inside to inside 1020 from that face down.
What are you up to Nye? I'm marking up the housing for the purlins. Yeah.
We can do kerf cut them. Kerf cut them. Yeah. Yeah. Good man. So yeah these are what the
purlins sit on, so the pieces that go across the roof, we're just showing you on the drawing
and then my sheet roofing screws to them. So Steve and Howard have just taken apart this truss
and Steve's going to put the tenon in the end of that post that goes into the bottom of the truss
and then put it back together and then mark out where the braces go.
Nice. Give it a go. I think it's in there somewhere. It's got a brace.
The big reveal. Yeah it's coming together.
There we go. Yeah.
So just to help orientate what we're looking at, we're currently looking at the back side
of the back cross frame. That's what this one is and it's the one with the intricate
bits on the ends because we've got all the braces and everything. I think you'll agree it's a pretty
pleasing shape. Obviously it's going to have that angled timber on the end of it and then it's got
the lean to on the side of that as well. So it's not complete but it gives an idea of what it's
going to look like and some scale to it and I think you'll agree that looks pretty cool. I'm so
pleased with it. It's such a pleasing design and shape and the guys have done excellent work.
Working really well and it's just coming out so I mean yeah it's just lovely. There's nothing
more you can say about it really. The shapes, curves, the joinery. It's just a work of art
really. You happy with how it's going Howard? Yeah it's all looking good. Looking good eh?
So yeah it should speed up a little bit. That one took quite a while because of all the little
intricacies involved in it. Getting all the beaks lined up with the top plates and the braces
and everything but they'll go a bit quicker now. Yeah that's going to conclude the video.
Hope you enjoyed it and thanks for watching.
