The Tensor 600X VR demo video shown in this video was produced by 'VSKYLABS Aerospace Simulations'. Using it here was following their permission. VSKYLABS website: www.vskylabs.com
Germany's Fraundorfer Aeronautics started test flights of a prototype two-seat gyrocopter in 2019, with a plan to introduce a six-seat version by 2025.
The Donauworth-based company unveiled the Tensor two-seater in May 2019, which it is now preparing for flight testing. Certification – initially as an ultralight aircraft for the owner-flyer and training markets – is targeted for "summer" 2020. Deliveries are scheduled to begin later that year, says Fraundorfer's head of sales and marketing, Klaus-Peter Leinauer.
The manufacturer's strategy is to expand the platform's capability and customer base in stages. Certification as an aerial observation and special mission platform under European Union Aviation Safety Agency regulations is planned for 2022, and approval for a six-seat variant suitable for the air taxi market is scheduled for 2024-2025, says Fraundorfer.
At an airspeed as low as 22kt (41km/h), the Tensor will offer similar capabilities to a helicopter but will be much quieter and cheaper to operate, says Fraundorfer. Take-off will require a 90m (300ft) ground roll, while landing will be possible within 30m, the company adds. The aircraft will have a maximum cruise speed of 115kt, and a range up to 320nm (593km).
While the gyrocopter concept is not new, Leinauer says the Tensor has a more refined design and performs better than existing platforms. The manufacturer used modern computational fluid dynamics analysis to optimise the rotor head and an airframe that features a fully enclosed cabin.
A pair of winglet-equipped wings aft of the cabin provide up to 30% of required lift at high speed, thus reducing pressure and drag on the rotor. Illustrations indicate that the six-seat variant will additionally be equipped with short canard wings for more lift and stability.
A pusher propeller – with three blades on the Tensor and six blades on the six-seater – is integrated into the tail boom, leading to an empennage with a horizontal tail plane and three down-facing fins. The two outer fins are connected, via struts, to the main wings.
Leinauer says Fraundorfer's design will provide a higher degree of aerodynamic stability than in other gyrocopters at both high and low airspeeds. In stable flight, he says, pilots will be able to take their hands off the controls and the aircraft will maintain its attitude.
While the gyrocopter will initially be powered by a Rotax piston engine, Fraundorfer foresees that the aircraft could alternatively be equipped with fuel cell- or battery-powered electric motors or a hydrogen combustion engine.
When the era was cancelled in February of 1959, Avro Canada began to lay off its workers.
Five of them would form their own company and produce the innovative Avian
2180 Gyroplane, a VTOL gyrocopter for the civil market.
In March 1959, the new company, called Avian Aircraft Limited and headed by Peter Payne,
set up shop in Georgetown, Ontario. They wanted to build a hybrid aircraft that combined the
VTOL performance of a helicopter with the simplicity and safety of a gyrocopter.
Their design was based on one the designers had proposed and turned down by Avro in the late 1950s.
They knew their design had merit and so began working on a smaller two-seat version.
The innovation in this design was a system to spin up the rotor blades before take-off
and to change the pitch of the blades, similar to that of a helicopter.
The gyroplane included a collective stick to change the rotor pitch from 0 to 4 degrees.
This allowed it to take off vertically in so-called hops. Once in a hop the main fan
would provide forward thrust and power to the rotors would be removed as forward airspeed
increased. Once travelling at sufficient speed the rotor would be completely unpowered
and the aircraft would act as a pure gyrocopter.
The initial design was to use the same system for spinning up the blades as their Avro proposal.
They wanted to pipe compressed gases from the engine through the rotor blades to nozzles at
tips. While innovative, calculations during the design phase showed that this system would be
ineffective. This motivated the move to a more traditional belt clutch and gearbox setup.
The first prototype, registered as CF-LKFX, was built around a central steel pipe that connected
the rotor blades to the fuselage. The open cockpit frame was made from square steel tubing and filled
with fiberglass. A 1.2m fixed pitch propeller with a chord of 30cm, which was built in-house
by Avion, was positioned aft of the central pipe and covered with a ducting shroud.
The ducting around the fan increased the thrust and provided directional stability.
The rotors and ducted fans spun in opposite directions. This was done to both balance the
torque and to accommodate the design of the blades which were optimized for helicopters.
The whole thing was powered by a 160hp 4-cylinder horizontally opposed Lycoming 0360A engine.
The first flight was on a wintry day in early 1960.
It was able to get airborne and showed good control and stability.
The prototype suffered an accident resulting in the loss of the airframe but this was not due to
a design flaw. A second refined prototype was built to overcome some of the deficiencies in
design. The new prototype, registered as CF-MTVX, had many improvements over the original.
The tubular steel approach for the airframe was abandoned in favor of an all-aluminum monocoque.
The shape as well as the canopy glass were refined. This both strengthened and lightened
the aircraft resulting in a 25% increase in airspeed. The propeller was changed from a
fixed pitch to a constant speed and the engine was upgraded to 180hp Lycoming 0360.
The first flight was on February 16, 1961. As testing progressed the fan size was increased
from 1.2m to 1.5m and finally to 1.8m. This prototype showed the desired performance.
It could confidently hop into the air vertically and had enough power to cruise at close to 200kmh.
It also had a low stall speed and could fly at 40kmh under full control.
Avian then built two pre-production prototypes in 1962. The first was the CF-NWSX which was
basically the same as the second prototype but had wheel covers. The second, CF-JTOX,
had a revised cockpit with larger windows, a fuel-injected 200hp Lycoming 0360 engine,
and a trailing nose wheel. By 1963 more than 300 flying hours were completed with favorable
results. In December 1964 Avian received a $540,000 grant from the Canadian government
to take the type through certification. CF-JTOX was selected for the certification
flights and the arduous process began in early 1965. Although the design was taken from scratch
to pre-production in four years, the certification process would take a further four years to
complete. Finally in 1968 the 2180 was certified by the Ministry of Transportation.
The first production airframe was built in November of 1956 and would be registered as CF-JTXX.
This would be later re-registered as N656JT. It was almost the same as the JTO but featured
riveted lightweight aluminum alloy frame, larger windows, larger door, and a 200hp Lycoming
fuel-injected IO360 engine. Although the design had good performance, the ability to hop vertically
and land vertically, and an appealing aesthetic, it failed to attract any buyers. The 2180 failed
to earn any money for the company and it went under in 1970. In 1972 the assets of the company,
including three airframes, went up for sale but there were no buyers.
The type certification and one surviving airframe was sold to the American company
Pegasus Rotorcraft Limited in 2002. They renamed it the Pegasus III but that company too failed
to make any sales of the type and its production future is bleak although still technically
possible. The Avian 2180 Gyroplane was an innovative hybrid aircraft with some unique
performance features. Unfortunately, the design failed to gain any traction with its
intended civil utility market and it faded away from the public imagination.