The Emglo Air Compressor Finally Died, Let's Fix It!

My Brother Donnie
258 followers
3 Video Views·Jan 13, 2025
today what we're working on her Chuck
we've got an old end glow compressor we
took it out of the fire system over her
because it's junk it does not work it is
broke so we're gonna try to fix it today
and you'll see that I've got a bunch of
equipment sitting around that I use all
the time like the tractors and the other
tractor and the two skid steers and I've
gotten a lards I've got floor floor guns
I've got drills I've got soles I've got
all kinds of stuff and a lot of it's
because of this right here I'll find
something like this it's already broke
I'll spend a few minutes with it play
with it figure out what's wrong with it
90% of the times I can fix it some of
the times I have to throw it away but
we're going to do this one today the
first problem is it's 220 I do not have
220 when I work on these houses and
stuff in little town I work on on the
weekends I run a generator 99.9 percent
of the time I have a little gas-powered
compressor but I hate running both of
them it bit not a lot nicer if I could
just plug this into my generator as I'm
running it so first thing I've got to
figure out if I can wire this for 110
you've got an old plug here I'm gonna
try to wire it up I'm not sure if I can
do it or not
I'm gonna try it and the compressor is
bad so we got to take the pressure off
and look at it but first I'm gonna try
to wire it up I'm gonna plug this in
here and we'll see if it blows up or not
hmm something's working know what it can
it's working a little bit but I've got a
sneaky suspicion that the motor it's
still wired for to 2002 o8 and I'm
running it on 110 overview on the point
side so I've got to figure out how to
move it over here I'll be back in a
minute okay so that's what we've done we
took basically this screw out
we took this screw out this bar slid
this way locked back in and I put that
screw back in I'm assuming it needs to
be there I don't know I'm not
electrician but we're gonna find out
hang on my assistant Otis Otis of course
course since then so stem
are you ready maybe explosive
so we got that up and running with them
the power to turn
okay for I'll do purposes we need to
close this hole oh okay now I don't know
I do not want to spend any money on this
machine yet because I don't know if it's
gonna work once it works then we'll
start spending money on so we need to
close this hole look and the guy that
changed it he put a hole no can you see
that but he put a pair of pipe wrench on
in benek so it's over so you know if I
had a 3/4 inch cap I could just screw it
on there and fix it and I'm trying to
teach this man right here let's go say
hi hola all right
trying to teach him how to use his head
from something more than a hat rack
because right now he just likes putting
hats on so I asked him how do you close
it up he said he don't know this is what
I'm going to try I can let air in and
out make sure the points work I can see
if the compressor works this is what I'm
gonna try to get in there and I think I
can do it I'll let you know okay we've
got a valve stem tool that you put bow
stems in with we've got our bent or bent
whatever plug reduce your adapter 3/4 or
whatever hold this right there
so right on that vise watch your fingers
okay we open this up just a little bit
we're gonna catch that down there and
close it up
now people have common sense about this
don't try to put a hundred pounds of air
on which it very well could hold 100
pounds there but the compressor is set
up at 40 pounds so there it is it's not
pretty but it's in there we're going to
try it and see what happened to this
gauge ain't moving
okay I took top over the port boat I
don't know what that is be honest with
you there's a hole over there that must
be the intake there's a hole over there
for the output this gasket looks fine
here this has got to come off soon and
this is a this is what I think might be
messed up basically it sucks it comes in
here and when it pushes out it pushes
out here and it's supposed to close this
but like this is open right now so if
the intake stays open all the time
it won't never make pressure because
it's just pumping up and down up and
down up and down up and down pushing out
here which you know all this to me is
common sense air comes in goes down the
piston pulls it down which makes a
vacuum which this opens it comes in it
can only open one way well when it
starts pushing this one's the one it
only opens one way it don't open this
way it opens this way so it blows out
and this locks back into place I've got
a sneaky suspicion this thing got real
hot because it wouldn't shut off it ran
for about a solid 20 hours and I believe
some old got up in here and got cooked
and held one in bhau's over and that's
what screwed it up I think if I can find
where it's at here I'll figure it out
but I'm fixing to pop this top off and
we're gonna look at the piston and look
at the backside
and see what's going on okay here we go
here's the piston just like I thought
there's a little wear on
I mean thanks probably fifteen years old
you can see all the grease and grime and
grit and all that in there which is fun
I mean that's it is what it is it's it's
gonna have that you can see it's nice
and flat that's the difference between
this and a small engine but you can also
see when this goes down the hash marks
are still in the sidewall
that means there's nothing wrong with
the cylinder or the walls 99.9% of time
there's nothing wrong in there because
you can still see the hash marks right
here is the problem there's two problems
actually this right here whatever that
is that's I'm pretty sure that's the
exhaust it's cooked it's stuck you see
that that's in the intake side
little pieces of this Bernie I'm gonna
take this part clean it up real good
I'll put it back together I bet money it
works and it's not gonna coach there's
nothing to fix it we might have to do
something here but it's gonna be very
minimal I'll show you when I get to the
port okay I pulled the first one apart
this is cliff this goes first that goes
down in them like so then then spring
but guess what if it springs in two
pieces and then this flips over on top
of it and then this on top of that
spring and it's work one both of them
it's work on this one too what's the
spine
that was the intakes off yeah that was
the intake side this is the compressor
someone have to work Springs and wide to
figure out how to fix hmm
start thinking and start thinking start
thinking how am I gonna fix it I'll
figure it out I'm gonna try to show you
this one it's a tag report that and you
got this
[Music]
this one is not rubble that's the pieces
from the other one okay so this one can
go right back together oh [ __ ] okay that
one's put back together I put it back in
there it's fun and that was the exotic
so this one I need spongy so that goes
in first like so I need to find the
spring so we'll see what we can do okay
I work on small engines I do not work on
air compressor what that being said
spraying spraying spraying spraying it's
fine I kind of like that because I
usually it's a tool all these
that one's all the way together I could
take my toys and this one here I think
we're gonna try this even though it
don't looking we're close to what that
did let's see what we can do with this
this is a trigger out of a steel weed
eater is what it is is the spring for
the trigger it's designed to be used
like so I'm going to look around and
make sure I don't have anything else but
this is probably gonna be our victim we
still got it
I just bend over that's all now I'm
gonna take my dice you can see something
won't take my dykes won't cut that there
and I'm going to a little past circular
I'm gonna cut that there and now you see
what I've got there I hopefully yo can
see that I'm gonna put that in there
then I'm gonna put that in there and
then I'm gonna get mom a shame I'm in my
pool
this pack is two for two
okay lock it in place seems to be
working
hopefully up so that that now seems to
be moving up and down that seems to be
moving let's put this thing back
together and see what happens
I mean just for shits and giggles no
everybody's going complaining that I did
not clean this surface I did not wash
this down but watch is trap oh this is
all I'm going to do it's a compression
we're not working on airplane wing got
nobody's life at stake
we got another I mean you see there I'm
gonna wipe this down watch so everybody
thinks you got to be a rocket science
scientists to do this job you wipe it
down I mean there ain't nothing on my
break wipe it down it's all you even
gonna do that's all I'm gonna do
wipe it off okay try to get some of the
grease off for them that's all I'm doing
hold up okay that goes like so okay we
got it back together here we're gonna
try it out buggy
[Music]
[Music]
[Music]
something happened I think he got it has
blowed to power we have too much power
going through too many extension cords
here so we'll have to go turn the
breaker back on and get back after it
here in a minute
okay here we go we want to plug this
back in now that were with her close to
the wall
that was heavy see what happened
[Music]
[Music]
[Music]
don't pick it dancing too
it just kicked off it's set at 40 pounds
and it kicked off at about 40 pounds
though so and you can tell that the
points that kicked up on so it shut off
on its own I can start it back up by
releasing some air pressure right here
that's the state to gets too much air
[Music]
[Music]
[Music]
