WET Didgeridoo - How to Modify a Wooden Mouthpiece for the Drop Octave

Learning Didgeridoo
4 followers
#Education #music # instruments # Traditional Australian instruments #Didgeridoo
So we're going to talk about adjusting a wooden mouthpiece on a didge to be able to play the
drop octave or the multi-drone technique.
And for those of you that have a stick probably crafted by a US crafter that's got a round
wooden mouthpiece, this is if you really want to take the next step and open that mouthpiece
up to be able to play the low note.
Now I really want to say, make sure it's something you really want to do and kind of get some
practice maybe with PVC first before you go messing with a nice didge that you have.
I don't really want to be responsible for a well crafted stick of another US crafter
being ruined by an experimental attempt at making one of these mouthpieces.
So just really make sure it's something you really want to take that step.
I've personally opened up a couple of my sticks that I've bought from other US crafters and
I just want to stress, there's no going back and there's no fixing once you start opening
up the wooden mouthpiece.
So just make sure it's something you really want to do.
So the mouthpiece is going to end up something like this.
This is one of a raw didge I'm working on and we're going to take a didge like this
that's got a standard round mouthpiece and it's about an inch and a quarter in size right
now and we're going to open it up and turn it into something like this.
Okay, so these are some of the tools that you can use to open up a mouthpiece and these
are some of the really cheap ones you can get at like a local hardware store and they
don't really work so well but they're helpful if you can't find anything else and these
are probably the best.
These are cut saw and I got these at Woodcraft.
You can get them at woodcraft.com or you can probably find them at some other carving stores
and these are just typical drum sanding bits to smooth it out in the end.
If you open up a didge that's coated with epoxy and you want to re-coat the inside of
the mouthpiece with epoxy, you want to wipe down the epoxy that's like right below where
you've hollowed it out with acetone first and that's going to, you want to sand it and
then wipe it down with acetone and that's going to create a true bond.
If you don't do that then the epoxy is not really going to become like one layer again.
It's going to be like one layer of epoxy sitting on top of another and it will probably start
to flake off in time.
So if you want to do it with epoxy again, then just make sure you wipe it down with
some acetone, acetone, whatever you want to call it and alternatively you can get some
tongue oil and you want to get some raw tongue oil, I'll post a link on this site and you
can also find it on Ben Hicks' site to get this stuff and this is just pure, totally
100% pure tongue oil and you can mix the first coating that you do inside the mouthpiece
with some citrus solvent to get it into the pores and then the consecutive coats you can
just do pure tongue oil and you don't want to leave the wooden mouthpiece that you've
opened up wood because it's probably just going to warp and get all spongy and nasty.
So the first step to making, adjusting a wooden mouthpiece for this drop octave is finding
which way your did sits.
Because the mouthpiece shape is going to be oval, it's going to go, you want a solid place
for your did to sit.
If your did is perfectly round and it kind of flows around, you might want to sand the
bottom edge down to be flat so that it sits on one spot.
So kind of put it on the ground as you're going to like, at the height that you're going
to play, sit, whatever, and rock it around until you find that perfect balance that
it's going to sit at.
Once you find that balance, you want to mark it with a pencil on the top, the bottom, and
then both sides.
And that's going to tell you how to open the mouthpiece so that it's always facing the
right direction when it's sitting right.
You want to have these lines come down the sides because you're going to sand off the
face of it.
So you're going to lose these lines when you sand it.
And we're going to put the concave face into the did.
So mark which side is the top.
You probably can't see it, but I've written top, it's upside down.
And that top on this, a sander like this, I'm going to use to push it against it to
get that concave shape because this is like, it's about a 5 inch diameter and it's got
a pretty good contour similar to your face.
So if you have an orbital sander, you can just kind of push it down into the center,
use just the edge of it to get that concave shape in there.
And before you work on any did that you care about, you're going to want to take a little
rag and shove it in down there a little bit so that you don't get a ton of dust down into
your didge.
Otherwise you're just going to fill your didge full of dust.
You can wash it out of course, but for ease of say, just shove a rag down there so you
don't have that dust.
So I marked which side is the top and now I'm going to put that to the side, have that
side mark facing up.
So you can see, it's starting to get the shape we want.
A little more, almost there, I've come a little bit too deep here, so I'm going to pull it
back this way, take down more of that edge.
Okay, so there you have it.
Now we have our concave face and that's going to make it a lot easier to open up diagonally
because you can see the rise edges and open up horizontally is what I mean.
And so now all we have to do is follow the edges outwards, it's a good guide and a good
start to do the concave shape first.
Okay, so again, always remember to stuff a rag in there if you don't want dust filling
up the inside of your didge.
And for this purpose, I don't want to open this guy up too much so I'm just going to
go straight to the drum sander and I'm just going to open it up a little bit in each direction
side to side towards the rise edges.
So you can see the rise edges, I'm going to open it up towards each rise edge.
Alright, so now I've roughed it out and I'm going to switch to the smoother grain drum
and just make it smooth on the inside.
Here we go, you notice it's just a little more oval now and you notice that the walls
are really thick.
I'm going to take down on the sander the walls until they're, I like my walls really thin.
So the thinner the walls are the less pressure you have to put against your face, it kind
of like, the sharper edge kind of like creates a better seal.
So I'm going to take this thick edge way down.
But all in all, that's pretty much the basics of opening up a wood mouthpiece and since
it's all wood exposed here now, you're going to want to coat it with tongue oil or epoxy
or whatever you like coating your sticks with and that's pretty much all you need to know.
