"Here's a look inside the Ford HF-35 transmission and how it works!
This transmission was from a 2014 Ford Fusion with almost 300,000km on it. The transmission is an eCVT, meaning it pairs two electric motors in a parallel axis setup with a power split device. The planetary gearset connects the starter motor (MG1) to the internal combustion engine and the traction motor (MG2). MG2 is linked through a countergear that is always driving the wheels.
Common failures on these transmissions are the bearings for the supporting gears, axles and motor rotors going bad due to a lack of lubrication. If caught early, the transmission's wear points can be rebuilt before further damage to the motor's rotors and stators (as seen in this video) or the transmission casing are done."
Today we're going to be taking a look inside the Ford Hybrid system to see what's inside
and how it works.
Here we've got an HF35 transmission out of a 2014 Ford Fusion Hybrid.
This one's got over 300,000 kilometers on it and as you can hear inside, it's pretty
noisy and something's wrong with one of the motors because they said it wouldn't start.
Taking a look around this transmission, we've got the bell housing here, an electrical connector
for some sensors, here are your two ports where your fluid is going to go in and out
to get cooled off by the radiator, and then this here is your park neutral switch.
Now around the backside here you can see we've got two giant circles which represents the
first motor and the second motor respectively.
Over here we've got the junction blocks with three phase AC cables that are going to connect
up here and here.
Then around the front side here we've got our fill port, our vent, and then at the bottom
is the drain port.
Now I'm going to begin this teardown by removing the front half of this case here.
Taking a look inside of this HF35 transmission, now first of all there was no oil inside of
here so I'd like to thank the previous owner for that.
Normally the oil would be sitting around this level with this being the bottom of the transmission.
This here is your oil pump and the oil filter.
Now there's three temperature sensors, one at the bottom here for the fluid, and then
one here for the first motor and the second motor.
Now I'm going to be calling this MG1 and MG2 respectively just because that's what Toyota
calls theirs.
Looking at our gear setup here, we've got the input shaft that comes from the engine,
then we've got one gear on the outside there that turns this counter gear, then we've got
another set of gears here that also turns this counter gear, and then we've got our
final drive at the bottom here with our open differential.
Now these are all helical cut gears on this angle which is supposed to reduce noise but
I'm pretty sure they're not supposed to be making so much noise when you rotate it.
Alright, I'm going to pull these gears out here.
First we've got this middle one, you can see there's actually three cogs on it.
Then we've got our final drive which is our differential.
Now this whole case wants to rotate backwards because the motors are so heavy.
Does this come out?
Oh it does, sweet.
We've got that one coming from MG2, we'll pull that out.
Make sure this doesn't drop off the table.
Looking at the residue inside of here, you can tell there were probably some metal flakes
in the fluid sitting at the bottom here.
Okay, looking at what's left here, we're going to remove this junction block.
Now we've got to get eights because it's a Ford.
Now I'll pull out the junction block.
You can see this just connects the outside wires coming from the inverter to the inside
stator wires that are over here which go to the coils.
We've also got connections to the temperature sensor so I'm going to remove that.
Okay.
Alright, wish me luck as I flip this case over so we can access the motors from the
other side.
Come on!
Alright, I'm going to remove the back cover next.
You can see there are a bunch of thirteens.
Let's see if this is as easy as the front cover.
Okay this doesn't look so cool, this looks really nasty.
That came from this motor right here.
Look at the giant cavity in here, you could hide stuff in here.
Take a look under here, we've got the first one which is the smaller of the two.
This is responsible for starting the engine but also taking some of the power off the
engine to charge the battery.
Over here we've got our stator windings on the outside.
Now like the name says, that stays stationary while we have the rotor in the center which
has a permanent magnet.
Over here, same deal, we've got the rotor on the inside and the stator windings on the
outside which are much, much bigger.
That's because this is the traction motor and mainly responsible for driving the vehicle
forward and backward and also recouping energy when you're braking.
Take a listen to this bearing, it's nice and smooth and quiet but when we come over here,
this one's loud and grumbly and all wobbly.
Definitely something wrong with that bearing and it's kind of sad because hybrid transmissions
in general are actually much more reliable than regular ones because you don't have clutches
and valve bodies and solenoids to deal with so if they couldn't even get the bearings
right, who knows how the rest of the car would hold up.
These long bolts hold the stator in, wow I'm surprised it's so easy to take out.
Usually there's a very strong magnetic field from the motors inside of here against the
coil windings.
So if you take a look on the rotor here, you can see burn marks and rashes from where it
was bouncing around against the stator over here and you can see the stator's kind of
burnt up a little bit too because the two of them are not really supposed to come in
contact with each other but because this bearing is bad, this rotor is just going to
tend to wobble around a lot.
This rotor has also got a lot of play so I suspect the bearing at the bottom there is
also shot.
Looking down inside with the stator set, you can see the housing for the oil pump.
Now this oil pump is also driven off of the input shaft through the planetary gear set.
So I'm going to remove a couple of 8mm bolts and see if we can get this thing out of here.
The oil pump and rotor assembly.
So this little nipple fell out and it's broken off, it's actually part of the oil passage
from here inside of the back half of the cover that's supposed to squirt oil at that bearing
that failed.
Here you can see the rotor, it's quite hefty, it's got a sun gear on it because that's part
of the planetary gear set that's inside of there.
You can see how burnt up the rotor is because it's been touching the stator and basically
shorting out.
Now this sensor that I unplugged actually tells the position and speed so the computer
knows just how fast and which direction this rotor is moving.
Inside of here we have the only planetary gear set.
This acts as the power split device and takes power from the engine, MG1 and MG2 and splits
it accordingly.
Just like that.
This is the input coming from the engine's flywheel and then we have the sun gear which
was the input for MG1 and then the ring gear out here actually collars out to MG2 eventually.
On the outside of that ring gear which is ultimately connected to the final drive we
have these splines and these splines are for the parking pawl.
If I put this vehicle into park here you can see the parking pawl is this little guy that
pops out and that's going to lock the wheels from moving when you're in park.
The rest of this just functions as detents so when you're changing gears on your transmission
you kind of feel that nice audible click.
But just like Karen next door this doesn't have any other function other than putting
a stop to things and leaving it in park and that's unlike an automatic transmission that
will actually move things in the valve body when you move the gears.
Also driven off the planetary gear set is this oil pump drive here and you can see it's
also coated in metallic material.
Two flat spots here that drive the oil pump which sits on the other side.
Now the oil pump is held on by both 8mm bolts and we'll pull off that assembly.
As you can see the oil filter is integrated with the oil pump.
It's not really a serviceable item because you pretty much have to tear down the transmission
to get here and if you look inside you can see there are a little bit of shiny particles
in there which indicate that bearing materials and other junk has moved in through here.
Probably remove this.
There we go.
I got my brother's old pillow case here that I stole off his pillow.
Doesn't need that, he'll never notice.
Just soak up some of that mess.
Put the oil pump on here and see if we can take it apart.
Pop this open here.
I mean at least there's oil in it, the rest of the transmission didn't have any.
Taking a look inside this oil pump you can see it's a gear style oil pump that moves
around like this.
Oil is going to be sucked in from the filter side over here and it's going to create oil
flow and push it out this way to the transmission casing.
This is geared to the planet carrier which is ultimately geared to the internal combustion
engine.
So I guess they figured you only need lubrication and cooling when the combustion engine is
on and not when you're in EV mode.
Fun fact though, on the energy models which are plug-in hybrids, they've added an auxiliary
oil pump so that's always running to cool things down.
Now turning our attention over to MG2 here which is our traction motor.
There is a bearing that's kind of pressed into the transmission for the rotor.
I'm going to just give it a little whack here.
So there's not much left inside of the casing.
This here is just the resolver which once again tells you the speed and the direction
of rotation as well as the position of this electric motor so you can control it like
a closed loop control circuit.
Taking a look at the second motor, this is the main traction motor that actually powers
the vehicle.
You can see the inside rotor here just like the other one is made up of a bunch of permanent
magnets.
Because you've got permanent magnets and you've got some solid metal here, this is kind of
stuck in here and I have to really push it out so I'm going to attempt to do that.
Oh, it actually moved.
Nope, it wants to come back.
Looks like the rotor disappeared.
Oh, it's all the way down the block.
So here we have the stator and they call it that because it's, well, stationary and here
we have the rotor because it rotates obviously.
Now this is a brushless design but if you were to put the coils on the rotor and put
the magnets on the stator then you'd need some form of communication to these wires
to the coils.
That would usually be done through brushes and boy would brushes wear out really fast.
That's why they don't use it on cars.
Now on the rotor, which is pretty dirty because it rolled halfway down my driveway, I'm sure
my brother wouldn't mind sleeping on it on his pillowcase.
We've got permanent magnets which you can see the line here where they kind of form.
Every time there's a line it changes polarity.
Meanwhile on the inside of the stator we have coils that form electromagnets when they're
energized so every little division over here forms a mini electromagnet and there's three
of them, U, V, and W, and then they just repeat themselves all the way around.
So let's say you've got U, V, and W here, you put one to ground and you energize the
other two and it forms say a north pole on one of these, well that means it's going to
attract the south pole on this magnet over here and the rotor is going to rotate to attract
itself to it.
Now once you keep alternating that really really fast that's when the rotor starts to
actually rotate as it's being attracted to the next nearest electromagnet.
Here's the first motor generator which is all burnt up because it was shorting up against
the coils due to the bad bearing which didn't allow it to center itself properly.
The bearings on the traction motor however are in pretty good shape and that's what it
should look like, not burnt up like this and that's probably why the engine didn't start.
Now taking a look at how the resolver works, you can see you have these little modules
here that have tiny little coils on them.
Now that's going to sit on top of this little cam lobe over here.
This cam lobe has a high spot and a low spot in four different positions around here and
as this rotates these electromagnetic coils are going to pick up that and send it to the
computer over here through the sensor and that's how you determine the position and
speed of this rotor.
Alright let's take a look at this planetary gear set or power split device.
Essentially we have power coming from the flywheel or damper from the internal combustion
engine coming into here.
Inside of here we have a planetary gear set.
You can see this here is the sun gear which is attached to the rotor of MG1.
This acts as a generator to take power from the internal combustion engine and charge
the battery and it also acts as a starter to start the internal combustion engine because
it doesn't have a dedicated starter.
That uses the sun gear.
Taking this apart a little further here you can see we've got a bit of a counter gear
and that there is splined to the ring gear of this planetary gear set which is over here.
So the ring gear's power ultimately goes to the rest of the transmission and to MG2 and
the internal combustion engine powers the planet carrier.
So here we've got the transmission put together here so we can look at how the power split
works.
Here we've got our planet carrier which is connected to our internal combustion engine.
Our sun gear is attached to MG1 and the ring gear attaches down here across to this counter
gear and then through another gear reduction to MG2.
Now furthermore this counter gear also has a pinion gear which attaches back here to
our final drive, our rear differential where our axles are going to plug into.
So essentially as MG2 rotates the wheels of the car are always going to rotate regardless
of what the MG1 or internal combustion engine is doing.
So let's say you just want to move down the road at very low speed.
MG2 is going to provide traction.
The internal combustion engine is going to be off so I'll hold that stationary and that's
what's going to turn the wheels back here.
You also notice that MG1 does rotate.
Let's say you're in your Ford Fusion Hybrid and you see a Prius Hybrid driving down the
road that you want to pass.
Well MG1 is going to start the internal combustion engine as a starter and once that starts to
rotate you're going to control the speed of MG1 in order to add torque from the internal
combustion engine to add to MG2 and pass that vehicle.
So essentially you're now adding the torques together so you can move the vehicle a lot
faster down the road.
So let's say by passing that car you've used up a lot of your battery power and now you're
just coasting along.
Well you can use that internal combustion engine to drive MG1 to become a generator
to recharge that battery pack while you're coasting down the road.
So now let's say you've been coasting along a little too fast and you see some police
lights pulling up behind you.
Well not only are you going to be pulling up your parents and looking for your expired
driver's license, MG2 is now going to be going into regenerative braking mode as you start
to slow down.
Essentially you've got a permanent magnet that's rotating about coils.
Those coils are going to pick up that changing magnetic field and turn it into electricity
and that's what's going to go back to the inverter to charge the battery.
Now by recuperating that kinetic energy back into electrical energy you take a lot less
wear down on your brake pads which is why you don't have to replace them so often on
hybrid cars.
Now while you're pulled over on the side of the road waiting for the cop to rent you a
ticket, your internal combustion engine can kick on at any time to allow MG1 to spin up
and charge the battery or to give you some heat on a cool rainy day like today.
So let's say you want to go backwards, well if you apply the current in the opposite direction.
Remember we do have that cam lobe with a sensor to tell position and direction so the computer
knows which way it's going and that can propel the vehicle backwards.
However if your internal combustion engine is on, they can only rotate clockwise.
That means MG1 must rotate at a much faster speed in order to counteract the rotation
so that you can reverse while your engine is on charging the car.
Now having the two motors side by side to each other is called a parallel axis hybrid
system as opposed to having MG2 and MG1 and the internal combustion engine planetary
gear set all in one axis.
It does make the case a lot more narrow for smaller vehicles although you do have to add
an extra counter gear in here, at least it doesn't have a chain drive or a belt drive
like a typical CVT.
Now the thing with these eCVTs is that the variation happens within MG1 alone, there's
no belt or anything that you have to stretch like in a traditional CVT and of course not
nearly the amount of complexity of parts that can fail, you just have to control the amount
of MG1 to either take torque away to charge the battery or add torque to MG2 so you can
speed up faster.
Now the good thing about this design is that MG2 is capable of driving the vehicle's wheels
all the way up to highway speed which is great if you want to sneak up on somebody at 62
miles an hour.
Now if you do want to find out a little bit more on the electrical side, how things work
and how DC is converted into 3 phase AC, check out my video on how hybrid cars work where
I go into more detail on the inverter system.
So let's take a look at why these transmissions fail, now this HF35 transmission is actually
known to fail quite often and it's mostly due to things like bearings and lubrication
which is pretty sad because hybrid transmissions are actually very simple inside with just
one planetary gear set, no clutches, no valves, no oil passages and things like that to get
clogged up.
Now we know that the front bearing over here failed and it also took off this nipple over
here that was stuck inside and that's what feeds it oil but what I also found was that
the bearing on the counter gear here was getting loose and the bearing on the final drive here
was also getting very loose and crusty.
Now as this starts to get loose and rattle around here, well the axle goes into here
and around here is an axle seal.
Now typically transmission fluid is kept right around the axle part here and if that starts
to move around because your bearing is getting bad then some of that transmission fluid is
going to leak out which you can see on the casing here is kind of covered in oil and
that of course accelerates the problem even further where bearings themselves start to
run dry and fail.
Now on the front half of the casing here you can see that this is starting to pit up and
that was getting damaged.
Now in this case you could get away with changing this race here but some of these actually
fail to the point where it bores a hole right through the case half and it pops out the
other side here and bothers the flywheel that's sitting here.
I mean at that point you must be playing your music way too loud in order to not hear that
transmission whining.
Now the magnetism on MG1 is actually pretty weak, it doesn't seem to stick that well whereas
on MG2 here you can see it as it goes very jumpy, that's as it alternates poles between
north and south.
If I do that here it actually moves pretty smoothly so I wonder if that's because it
was damaged.
I also find it kind of sad that simple things like bearings are what let this transmission
go.
It's actually a very common failure across all of these hybrids and if you have one make
sure you listen out for that whirring sound before it bores a hole right through your
transmission.
Now that's a look at the HF35 transmission from Ford.
These hybrid transmissions were developed in house from Ford as opposed to being co-developed
with Aethon.
Very unique to have a parallel axis hybrid system although they all pretty much boil
down to this planetary gear set.
Make sure you subscribe if you want to see more videos just like this one.