9. Glazing Textured Wheel Thrown Vases

Making ceramics and glass
106 followers
Welcome. I hope you're doing well.
In this video, I will show you how I glaze the two pots
that I showed you how I've thrown in video number six,
where I did these wonderful crackle effects on the side.
You probably remember that.
I've thrown two different ones.
And in this video, I'm gonna show you how I glaze them.
In video number six,
I showed you how you can create
these wonderful crackle textures on your pot.
And in video number seven,
I showed you how you can trim these kinds of pots.
And in addition to the crackle effects that we created,
I also made some chattering effects on the top of the pot.
So today, we're gonna glaze them.
They have now been brick fired and they're ready for glazing.
So I like these crackle effects to be as strong as possible.
I like the contrast between the top and the cracks
to be as powerful as possible.
And the biggest contrast, of course,
is between black and white,
but anything even close to that
will still emphasize the crackle effects.
So we have two different pots.
One of them is just a pure stoneware.
And it's not completely white, but kind of whitish,
whitish enough for me to just more or less
leave that on the surface.
But the crackles, I would like to make black.
So in order to do that,
we will put a stain, a black stain in the cracks.
So the way you do that is that you take black stain,
it's a powder you can buy in most pottery supply stores,
put it into water, put a little more water into it
than what you would usually do
because we need it to get into the cracks.
And then slowly we're just gonna paint it on the entire pot.
Don't worry too much about being precise about it.
And if it doesn't cover or go into all the cracks
when you brush it on,
don't worry too much about that at this point
because we're gonna even it out in just a second.
Once you applied the black stains
to the entire surface of the crackle side of the pot,
you leave it to dry just a few seconds.
It dry really, really fast.
And once that's done,
you're ready to wipe it off with a sponge.
Now I take this bucket of water
and I frequently freshen up the sponge in this water.
And then it's time to just rub it off.
And as you can see,
if you rub it off with a rather big sponge,
you're only gonna rub off the color,
the in this case, black stains on the surface.
And it's gonna leave the black stains in the crackles.
And so now that we're done,
you can see that we have this wonderful pot
that is black in the grooves and the crackles
and just pure ceramic stoneware on the top of it.
Now, the second part,
you probably remember that I put a bit of black stain
into the sodium silicate to create a darker surface.
So once it brisk fired, it's not completely black,
but it's still a little grayish
and it will be darker once we put a clear glaze
on top of it.
But as I said, I like the contrast.
So for this pot, I would like the cracks to be white
and the surface to be as dark or grayish as possible.
I'm gonna try something I haven't tried before.
In this case, I'm gonna use white stains.
So a white powder dissolved in water,
and I'm gonna apply that the same way
that we did with the black stains
to the surface of the entire pot.
And again, don't be too worried about if you apply enough
or if it goes a little out over the edges and stuff
because you're gonna wipe it off again.
Okay, so now we are ready to wipe it off.
And that is exactly the same way
that we did it with the black stains.
A big sponge, use water,
not so much that it runs into the cracks,
but enough to get all the stains off the surface of the pot.
So this is how it turned out.
And as you can see,
there's a small layer of white stains
that appear to be on top
of the black stained crackle surface.
I think maybe I will wash it a little more
to make sure that it doesn't go too gray.
But also once we apply the clear glaze,
the dark part, the black stains part of it,
I believe it's gonna be darker.
So we're gonna hope for that.
At least this is kind of an experiment.
As I said in the beginning,
and as I showed you in video number seven,
I also did this chattering effect on the top of the pot.
As you can see, there's this effect here.
And just like the crackle effects,
I like that to be emphasized as much as possible.
But I don't wanna use the same technique
that I've been using for the textured effect
on the side of the pot.
Instead, I could use a normal glaze, a celadon glaze,
usually breaks really nice
on the chattering effects like this.
But in this case, I would like the separation
between the top color and the rest of the pot
to be as sharp as possible.
And with a normal glaze, as you probably know,
it's always a little bit difficult
to control how much is gonna run or not.
And I don't like to apply my glazes with a brush.
I like to dip it, and it's difficult to dip it precisely.
Of course, I could use some wax to control it.
But in this case, I'm gonna show you a different technique
that I've been applying to a lot of these chatted effects.
And that is using an underglaze.
For underglaze, I like to use these Dunkin underglazes.
I admit it, it's quite expensive solution,
but I use very, very little on these pots.
So I use them now.
Just recently, I found a good recipe
for mixing up your own underglaze using stains.
And if you already have stains,
you can mix these colors and make your own underglazes.
I'm gonna show you the recipe here
and also down in the comments, so you can try it out.
I haven't tried it myself,
but I hear from a good friend that it's working well.
So I think I'll try that next time.
But for now, I'm gonna use a little bit of this underglaze.
The other reason I'm using the underglazes
on these particular pots is that
the side where the crackles are is gonna be very graphic,
white and black or gray.
So I wanna apply some color.
I like, you know, stand out a little bit with my pots.
So I like a stronger color on that layer,
that border on the top where we have the chatted effects.
So for that, the underglaze is gonna work nice.
Also, in the end, it's gonna be very easy for me
to just apply a clear glaze on top of the entire pot.
So let's move on with that.
Okay, so first of course,
we need to decide what color we wanna use.
And in this case, I'm gonna base it on a dark blue color
that I really like.
But I'm gonna do something that I found
works really great for these chatted effects.
And that is to start out with a brighter
and lighter color below the blue one.
And that's gonna create some, you know,
interesting combinations in the color.
So we're gonna start out with this.
And again, you're gonna need very, very little.
So we're just gonna put this out here.
That's it.
And then you need a good brush to apply with.
A brush that can contain enough of the underglaze
so you don't have to dip it too much.
And then it's basically just to apply it.
What is interesting with these underglazes
is that if you only put one layer of this underglaze,
it's gonna be matte.
And of course, if you put a shiny or blank glaze
on top of it, that's gonna leave a normal kind
of a glazed surface to it.
But if you apply multiple layers of this underglaze,
it will actually work out just as a normal glaze.
It will be blank and look really good.
So I'm gonna apply a good layer of this.
Now, these Dunkin' underglazes,
I don't know if this is the case with all underglazes,
but this kind of underglaze from Dunkin'
is I think they recommend that you apply it
only to cone five or maybe four or something.
I've been firing it up to cone 10,
and that works great too.
So don't be too concerned with that.
It actually works okay.
Even the most bright colors I've been using,
I've been using a bright red one,
and even that one doesn't burn out in high cone firing.
So you can go ahead with that.
So now we put the orange there.
Now, what I'm gonna do here is
I'm actually gonna take some of it off again.
So I'm gonna use a little bit of a sponge here.
Let me just see if I have one here.
Because what I wanna do is I wanna only leave
the bright color in the cracks, in the grooves.
I wanna leave very little of it on the top of the pot.
So I'm gonna brush off some of that.
Okay, now I pushed it a little bit,
so we need to push it into place again.
Okay, now we're ready to put the blue one on.
And I have another bucket or another bowl here for that.
We're gonna put just a little bit of the blue one in here.
And I have another brush similar to the other one.
And now we're gonna apply the blue glaze,
or the underglaze, sorry.
Sometimes there can be areas where it's difficult
to get it entirely glazed.
And then I try and just stop the wheel
and just focus on these areas.
So I think that's good enough.
I'm just gonna use the underglaze on this part
with the chattering effect.
And I'm gonna leave this just clear glaze
and this top is probably gonna end up
with a third glazing with gold.
But if I do that, or when I do that,
I'm gonna go get back to you with that
and show you how to do that.
So now it's time for the next pot.
So we're gonna put this aside
and just give it a clear glaze.
Okay, so now we're ready for the second pot.
And for this one, I'm gonna go a little more crazy
because I'm gonna use a red,
it's called Really Red, and it is really red, CNO74.
I like that, I use that a lot.
It's very strong.
And I'm still gonna use the orange one,
the neon orange one that we used on the other pot too.
And I apply a small layer of that at the bottom
and then apply the red on the top.
I don't know if you remember,
but I told you in video number seven
where I did this, the trimming and the chattering effect,
that it was a little bit too dry for making the chatter.
So the chatter marks are not so deep.
So in this case, with this pot,
I'm not gonna actually wipe off the orange,
but I'm just gonna apply a bit of the red on top of it.
Sometimes you need to let it dry just a little bit
before you apply the second and even the third layer,
but it dries really, really quickly.
So it's not a problem.
So I think that's ready.
It's very red.
And again, I think maybe I wanna make a gold top
for this one.
I'm not 100% sure.
I will wait until I have done this initial glaze.
A gold glaze is something you add in a third glaze
and it goes to a much lower temperature,
but I'll get back to you later with that.
So this one is ready.
So the last step is to give it a clear glaze,
which is what I decided for the two pots that I throw.
And I always start out by putting the glaze inside
and taking it out again.
So I'm gonna use this.
Always have a wet spot ready when you do glazing.
Just like this.
I'm just gonna put it in the pot.
And then we're just gonna roll it around a little bit inside
and then dump it into this pot.
Remember to completely empty it
and make sure that there's no little drips hanging there.
So, that should be fine.
And now I'm just gonna let it dry a little bit
and I will do the same way.
And turn it around and then pull it out
and put it into the pocket with the glaze.
So, and again, shake it.
Make sure that you don't have any drips hanging
that may act in a funny way.
That's it.
And since the rest of it is gonna be glazed
with the same glaze,
I don't bother too much about this dripping air.
So, I'm gonna let them dry off for a few seconds.
So, to glaze the outside of a pot like this,
I find it easiest to dip it.
But it depends on how much you have to hold on to.
In this case, I have a foot
that is good enough for me to hold on to.
If the foot is not big enough,
you can't hold on to it
and then dipping it can be a little bit tricky.
But I think in this case, it should work out.
So, let's try and see how that goes.
And this is why you wanna have it dried on the inside
because then you can turn it around like this.
And just push it on the table.
And I think that should be fine.
And then we're gonna do the same thing with the other pot.
Again, just dipping it.
So, that's it.
Now they're ready for firing.
So, now the pots have been glaze fired
and we can take a look at the result.
But first, I wanna excuse for two things
that I forgot in the previous clip
when I was putting on the clear glaze on the pots.
The first thing is, I was holding the pots with my hand
as I was dipping it.
And my fingers somehow, you know,
covered a little bit of the area where I want the glaze.
That's not a problem.
What you do is, after it dries up,
you can apply a little bit of glaze on these empty spots,
just dipping your finger into the glaze and dipping it on,
leaving, you know, like a few drops
and that will even it out.
And make it look perfect.
So, that was the first thing.
But maybe the most important thing is
that I forgot to show you
to wipe off the bottom of the pot,
which is very, very important
because you don't want any glaze to be left
on where the pot stands in the kiln
because then it's just gonna burn onto the kiln
and you're gonna destroy the kiln and everything.
So, you gotta wipe it off
and be very, very thorough with that.
No glaze should be left at all.
You can have some glaze on the inside
if you made a foot like I did,
then you can apply some glaze on the inside.
I did that.
Some people like that.
Sometimes I do, sometimes I don't.
But in this case, I did.
So, let's look at the pots.
The first one came out really nice, I think.
This is the one where I used the pure stoneware
on the outside and I colored the cracks with black color.
I think maybe you can see it a little better here.
And I think that came out very beautiful.
And as you may remember, we put this red,
very red on the top where the texture effect was made,
the chattering effect.
On the very top, I just left it pure stoneware
with the clear glaze, of course.
I'm thinking maybe I will apply gold to that top.
It's gonna, you know, maybe be interesting.
I'll show that in a later video.
I will do a gold firing very soon
and I will show you how we apply real gold to a pot.
It can look really, really nice.
So, I think this one turned out nice.
And as you can see in the bottom,
maybe you can't see it, but there's glaze on the inside,
but I wiped off, of course, this part of it
and made sure there was like a few millimeters of edge
between the bottom and where the glaze starts
because when the glaze firing goes on,
the glaze expands a little bit.
And so, you've gotta leave room for that expansion.
Otherwise, even if it doesn't actually touch the base
of your kiln, it can still burn on.
So, this have, even though I did this,
this still have like a very few small spots here,
but I will grind that off.
I showed you in another video,
I think it was number eight,
how you can grind your pots in an easy way.
So, jump back to that if you wanna see that.
The other part also turned out very nice.
And remember, this was the one where I used a slip
that was mixed with black stains to make the surface dark.
And as you remember in the last clip,
it actually looked almost grayish,
but now when the clear glaze had been applied,
it actually turned out black, as black as I wanted it.
Not completely, but enough.
And the cracks have turned out.
This was an experiment, remember that,
where I put the white stains into the cracks
and it actually turned out much better
than I was hoping for.
It is clear white and it makes, of course,
the contrast very strong.
I like that.
We applied the blue to the textured effect on the top,
but as you see,
even though I tried to apply it very, very sharp,
there's still some edges where it's not completely sharp.
I mean, it doesn't matter.
I mean, it still looks really nice.
And I was expecting to get a little more sharp,
but again, that's what happened with glazing.
Even though you've done it a lot of times
and you think you're doing it perfect,
sometimes it turns out not exactly how you like it.
But in this case,
I don't think it's actually gonna matter so much
because just like the other part,
I think I'm gonna apply gold to the top,
covering both the blue and the little white piece at the top.
I'm not 100% sure about that yet,
but I think it turned out nice.
And in the bottom, I don't know if you can see it.
Yeah, I think you can see that it's shining a little bit.
At the very bottom, I have glaze.
On the rim, of course, on the foot, sorry,
of course, there's no glaze.
So that's how they turned out.
I'm just gonna show you a couple of examples
of similar parts that I did.
This one is a little bigger and has some flowers in it.
Also with black stains in the cracks,
but in the top, I applied a normal glaze.
And as you can see in this example,
it's actually very, very sharp.
So what I did is I first glazed the clear glaze,
then I applied wax.
You can get some wax resist that you put on,
and then the glaze won't stick to it.
And then I dipped it in the top to have this bluish top.
I think this one turned out really, really nice.
Another example is this one.
This is actually wood fired,
which is a completely different thing.
But I think in video number two,
I'm actually gonna, I'm showing you
the whole wood firing process that we went through
where this part was also made.
But this is also, this is with a different kind of clay.
It's a little more red, brownish.
But I also applied a color glaze on top of it,
which makes it look also very interesting
on a glazed top.
So that's all I had for today.
Remember to subscribe to my channel,
then you will be notified about new future videos.
I have tons of ideas.
If you have any ideas for things you want me to show you,
please add in the comments or write me a message.
And I hope to see you soon again.
Thank you.
♪♪♪
