Restoration of a Rusty Movement - Omega Cal.26.5 SOB

Hello, everyone. How are you? Thank you for watching the video. This time I'm going to fix a 1930s Omiga. I'm a man of about 90 years old. This guy was sold as a repair item. And, there are many problems. I don't have a hand. It's filthy. I don't see the case as original. This time, I'm going to focus on how to fix this dirty move. I'll take the dial out. The dial screws are dirty. I'll use oil. Before using oil, I want to remove many parts. The oil screw is the other screw. I'm going to the right side to remove the screws. There's a seat below, but I couldn't remove it. I thought there was water in the oil screen. In the case of the Clouseau Watch, The circuit board is irreparably damaged. It's over. But this is a mechanical move. If the owner lets the watch dry, After the accident, This movement will not cause damage. Before I remove the dirty screw, Put the oil in and leave it for a few minutes. It was the first time I'd used a dirty screw. There were many failures. Because I was in a hurry. What I've learned, You must work safely. Wait for a few hours, It's better than brake parts. This is a 90-year-old watch, so... It's very difficult to find brake parts. It's a good choice to buy other moves, but It's not good for me. I couldn't get rid of the canon. I'll put the oil in. In the meantime, I'll remove the barrel bridge. I removed the setting return screw and other screws. Compared to other screws, Especially compared to key work. This is a key work. The screws are so dirty. I'm trying not to put too much energy into it. It's hard to break the screw. The other screws are dirtier. Put some oil in it. I was able to remove the screw. Because the chemicals are dirty, It looked very dirty. I had to get rid of the dirty stuff. I didn't care. The keyword has been almost removed. The wine-making stem was not removed. between dial and backside I'll take the train wheel bridge out. But, another screw is dirty. I'm not going to lie. I couldn't remove one of the screws. I'll wait. I had to remove my stems. That was my last choice to remove. There was something dirty between the wine-making stems and the backside. The main spring is very old, but... It was okay to use. Wash it nicely, I used it to save some of the history of this thread. Finally, I was able to remove the main character. I'm going to put a movement in the paint oil, I used an ultrasonic cleaner. This screw is so dirty, I folded the screw's head to remove the bridge. The central wheel bridge was fixed. So, I went back to the ultrasonic cleaner. Disassembly is almost over, but I'm not going to be late. There was another hidden problem. I thought it was because of the dirty stuff. Actually it was because of the dirty stuff. But there was another reason. This wheel bridge had two long pivots that connected hands. And, it was curved. Therefore, I could not remove it in a straight line. It's dirty to clean with an ultrasonic cleaner. I washed it with an auto parts cleaner to remove heavy dirt. Then, I removed the filthy stuff. I reacted to dirty things and turned purple. Then, I polished the pieces with my hands. On the hand side, there might be too much sanding paper for the pivot. However, metal polishing compounds may be easier to use than sanding paper. After removing the dirty and polishing pips, I cleaned all the parts of the camera. I didn't shoot this video scene because it wasn't anything special. After cleaning is finished, I'm laying the main spring barrel. I'll put oil on the main spring barrel and fix it. This is a manual wine-making watch, so you don't have to put the main spring grease on the barrel. Instead, the main spring ballet has a hook at the end of the spring. I need to attach a hook to the main spring barrel. It's a little difficult to get hold of the barrel. I put a cutting in the middle of the spring. There's a hole in the bottom of the main spring. I need to attach the barrel. This ballerina has a hook-attachment cut. I've closed the lid tightly. Let's combine the movements. Please see this piece of glory. All the dirt has been removed. However, in the cleaning process, the playing also caused damage. I removed it somewhere. But, overall, it was a huge success. Except for a spring and a screw, I was able to get all the original parts. I'm glad I was able to remove all the dirt. One piece can be found for tens of dollars and a month. I'll combine the tray circles. And, I'll get the main spring cell. It was pretty easy. There's nothing special. The bridge is attached. I'll combine the clicks. I'll say it again. The crown's wheel is inverted. A typical screw has three lines on its head. This is not a screw. There is one more thing I must say, The jet wheel must combine the click and the winding wheel. Then, I will destroy the parts and the screw. Then paint Jewel. I changed the combined movement of the dial sides. I'll combine the keywords. After several cleaning challenges with an ultrasonic cleaner, Winning pins and craps wheels, It's in a usable shape. Other parts, small screws, I did the cleaning and polishing. This part is not bright. It will be usable. I forgot to install the mini phone. Install it, I'll fix the screws. The movements were almost combined. But, there is another challenge. I mean, it's a balance wheel. The hair springs were tight. Wipe with petrol, I'll make a picture of it. This is the result. Now it's in the shape of a good spider. The combination of balance wheels is, It's always a challenge for me. Because this part is so small. Put a little oil in it. I'll put it on the back of the bus. I'll put the controller down. This regulator has a subtle pin. It is difficult to install balance wheel. I like to adjust my movements. I need to adjust the height. This is the lateral direction of the hair spring. I'll install the head spring with the regulator pin. Check the position of the head spring. And fix it. I cleaned the other side of the hair spring. I also cleaned the hair springs of the Pallets. You don't have to clean the pips. Hearspring and pivot If the particle beam is not properly installed, Be careful installing it. Finally install the balance assembly. I believe in success. Let's see what happens. The performance was better than I expected. But when I check the details, I can't see why. How can I help you? I move the center wheel with a flexural fit. It'll get the ball moving. If the frequency is too low My hands are not moving. In that case, to raise the reflection To adjust the frequency I've been trying to get you to stop. This stacking was untouched. I'm not going to tell you. One of the most useless things in the world. I changed the dial. I couldn't find the right hand for the dial, I was able to get this move with a dial. It's a controller, but... I actually like the new look. I'm going to buy this original dial. I'm looking for the right hand and case. It may take years, For this stacking you This steak has survived for over 100 years. So, that's it. Thank you for watching. I'm glad you enjoyed this video. Please give me a high rating and channel registration. I'll be back soon with a new set of rules. So, goodbye.