Learn tricks and tool adaptations for easier, faster and cleaner stone setting from New Approach School for Jewelers founder Blaine Lewis. Want to see more from Blaine? These videos offer extreme magnification and 3D animation, where he demonstrates even more about the art and techniques of setting stones: http://ow.ly/Qpqk30mf53T
Rio Grande stands for makers who create with their hands and their hearts, and who are courageous enough to make jewelry their livelihood.
Hi, I'm Blaine Lewis, founder and director of New Approach School for Jewelers,
located just outside of Nashville, Tennessee.
And today I'm here with my friends at Rio Grande, and we're shooting a tips and tricks video
where we'll show different little adaptations to burrs and tools
that can make your life at the bench a little easier.
I hope you enjoy.
So what I'm going to show is some information about heart burrs.
Just want to take a little dive into a heart burr.
Like almost all of our bearing cutting burrs, they have directional teeth.
So if you look here, you can see that there's a direct distinct angle to one side of the teeth.
So these are almost have like a tractor tire grip one way.
They don't have a lot of grip the other way.
A couple of years ago, I just was playing around and I got a big surprise.
If you run a heart burr backwards, it'll still cut.
It's not as efficient.
It's not as fast.
But one thing it does is it takes out sometimes the horrible traction effect of the burr
and then the preceding wrap around the burr that can just be so damaging
and kind of frustrating to us as stone setters.
So let me show you some neat things about this.
I'm just going to show on a toothbrush for a second just to kind of
just further demo a little bit about what I'm talking about.
So you have no mistake about direction and so on.
So if you look at the burr this way and turning normally right,
it's got an awful lot of traction and grip and cut.
OK, so today's modern flex shafts and all the micromotors,
almost all the micromotors that I know have reverse setting on them.
So if we put our flex shaft or micromotor in reverse,
what we get is very little grab, but yet it still cuts.
So let me show you this on metal.
So I'm going to do some prong cutting on this mounting.
These are fairly robust prongs.
And here's an orange CZ we'll put in it.
And so in doing this cutting, I'm going to run through just a little simple
kind of the proper place for the stone to be set at.
What elevation on the prongs is proper for this to be set at?
Some of that is in the eye of the beholder, and it certainly takes in,
you certainly must take into account the culet sticking out the bottom.
And in this mounting, there's no danger of that.
I normally go by what's called the rule of thirds.
So I take the pavilion of the stone and divide it into thirds.
So I would have the upper gallery wire, so to speak, at the top of this mounting here.
I would have that hit at about a third down from the girdle, leaving two thirds.
So that would put it in an elevation that looked something pretty close to that right there.
OK, so having picked that elevation, I'm going to go in and I'm going to use the burr
and absolute reverse.
You can kind of see it on my skin, too, that it just doesn't have
that much traction running backwards now.
It feels funny on the finger because the way it wants to pull the skin is so different.
But besides that, the controllability of it is just really good.
So there's one seat.
Let's cut another.
It's good for a rough end.
Let's cut about a third into these prongs.
This stone is just slightly undersized for what it could be.
But like most mountings, you've got a variable, and this is certainly within that scope.
Speed is another thing.
I think that not enough is talked about on the proper speed to operate a burr.
Machines go by a chart that calculates the size of the cutter and the feed rate.
For us, we're having to do this all by hand feel.
And for me, you've got to realize, you have to feel the fact that
you've got to operate the burr for its size at a speed that will cut.
Little burrs have a very small linear outside dimension, so they run faster.
Bigger burrs don't need to be run as fast.
So you just kind of play with the foot pedal until, like right now, I'm not doing a whole lot.
Speed up a little bit, and I'm doing considerably more.
So it's a constant assessment in the way the burr is cutting.
I've seen burrs that begin to cut well, get a little clogged in metal.
If you vary or change the speed of what you're doing
partway through the process, it'll start to cut better.
It is definitely something that you should have a tactile read, a feedback from,
and how you feel like it's doing, and experiment and try other things.
Okay, so getting a little closer.
But you can see this cuts.
If I didn't tell you I was running backwards, you wouldn't know.
Fairly efficient.
So even in the pavilion angle, I'm going to tip the pavilion angle back a little bit.
I'll raise this bearing up a little bit, I believe.
Got some thicker girdle to compensate for.
I'm going to look at the pavilion angle, and that's pretty close.
I'm going to tip it back just a teeny bit.
Just this one side.
The big thing with this, and in the first tips and tricks video we shot was all on burr control.
There's a lot of information about how, a lot of subtle technique about how you
hold the burr properly.
All right, so one of the things I do before I want to start pulling back prongs to check the fit,
is let's visually check the fit.
Let's use a good loop or a microscope.
Stone setting is something that definitely goes beyond the Optivisor for most situations.
And you can optically see this here, that these guys line up pretty good.
Should be a pretty decent fit.
The bearing on the right side right here is a little shallower than the other.
As we turn it, probably show a little deeper.
That just tells me I need to push this a little bit to the one side, and just to do a little bit more.
Turn it this way, that looks better.
I'll take a pair of pliers and pull this back.
Ease the prongs back a bit.
Check to see whether this will slip in.
Not quite.
They require one or two more cycles.
Don't want to push it out any further than I have to.
So just using a pair of chain nose pliers, ease these back.
Some might take two prongs and pull them way back and leave the other two alone.
I'm not partial to that as much, unless there's real circumstances about the design of the ring
and one way it's very difficult to move.
So this has gone in now.
And before I go, it's always, you want to see it set.
So you look at it and if it looks right, you want to push it up.
But I want to do a little inspection on what the girdle actually looks like.
So this stone could have been set with a setting burr
and then all metal forged over in some manner on top of the prongs.
It is certainly one of the staples of stone setting.
But if you can master your burr control, this is a method that I use probably 80%
of the prongs that I do.
It just has a, it's faster.
It's more efficient.
There's less acute bending of the stone.
There's a lot of good benefits to this.
But one of the things that can be just a little bit trying is,
is that if you do have a heavier girdle,
the heart burr is going to give you the same cut every time.
Now you can manipulate that cut a little bit
and you can raise the heart burr slightly
and that will give you a kind of a small flat right there.
If you do, a lot of times that's a little, it's a little dangerous.
So I'll show you a real simple way to alter that.
So if you look on the left side of this CZ,
you can see that definitely that the girdle is thicker than the profile on the right.
So I've seen a lot of things that people do to alter this.
Saw blades, all kinds of stuff.
One of the simplest, cleanest ways to do it is to use what's called a cross cut burr.
This is not a Crouse burr, which is probably much more common burr.
I'll show you both and the reasons why I like the cross cut in this manner.
This is a tapered cross cut, so it gives me some varied sizes that I could use comfortably.
This is a Crouse burr and it looks, it has the look of an elongated medieval spear almost.
It's very, very sharp and it's found my finger more times than I'd like to admit.
This is a cross cut burr and the cross cut burrs come in smaller sizes.
So let me put them side by side here a little bit for more.
They're kind of up close.
So a lot more variance in size on the cross cut and smaller.
So what you'd want to do, what's really most important is,
is how is the size of that burr compare to the profile of your girdle?
And for me, the tip of this is about just right and that's going to help me to go in
and adjust the, this on this side, just a little bit.
Controlling the burr, real simple with this because we're going to go crossways,
which, which means we're not, we don't suffer prong run around with this to any,
to not at all for this, but you can run up the face of the prong this way a little bit,
but it's not very, not anywhere near as likely.
So a little touch of this and that, if I can get in close enough causes just a mild shoulder effect.
Just a very mild shoulder effect right there.
What's so nice about this, and I use this for altering cat for,
if I have to set a cab in a prong or something like that,
this is so nice where you can just pull down and you can cut on the fly,
change and take that shoulder effect off.
Let me show you again, both a little heavy on this side right here too.
So for a clear vantage point of what I'm doing, it's this way.
You can see what's happening as far as the orientation of the burr,
but it's this way that we see the actual silhouette of what's being removed from the prong.
So this is good right here.
And then just a little shave down to take that shoulder effect off.
Okay, now the other two prongs should probably use a little adaptation,
but let's just see what this looks like now.
It's a little softer.
I believe that fit is nice.
I'm going to do just a little bit more on the bottom, on the pavilion side.
I'd like to see it set up in there a little bit more.
That's better, that's better.
Okay, so now a simple technique for setting prongs like this,
as far as bringing them forward, is to take a pair of pliers.
And I like to hold my pliers in such a way that they're actually coming out the end of their,
they're aligned with the end of my thumb in the same way I might use a graver.
So I am not a fan of holding pliers in this method right here,
because for a lot of prong setting, it puts the strongest, your strongest fingers,
your pointer finger and your middle finger,
at the longest point of the leverage factor of the pliers.
And it's coming out the bottom of the hand.
I really prefer a hold like this, as far as being able to control the pliers much better.
I have less slippage in doing that.
So what I'm going to do is bring these prongs up in opposing sections.
So it'll be like this.
Try to bring them up evenly.
That can be controlled by tipping the prong, the plier angle down a little bit.
If I want to push the prong that you see here on the right more than pushing the left,
that can be altered very easily by doing that.
And if I come up a little higher, it's definitely obvious which way I'm going to go with it.
Now I'll bring it back a little bit because I really didn't want to go that far.
Then we'll come forward with these.
You can see me shifting the stone a little bit because it needs to be shifted.
I need to bring a support here, bring this prong over a little bit.
This one's a little shy in its bearing, but just bring it up just a little bit.
Okay, now I'll start to kind of clean up, get some beeswax off of this,
do a better inspection of what's going on.
I've got my stone is set.
I want to show you some things about when you have, say, a stubborn prong
that doesn't want to go over as much.
A lot of times when you go to push and you get to the point where you're touching,
but you just would like to bring the prong metal down a little bit more,
you can simply grab the prong by its side a little bit.
You actually begin to alter the grain boundaries of the metal
and you get it to move in a way that just straight-on pressure doesn't provide.
There's a lot of information about that in the Princess Cut video
on just how to move difficult prongs.
If this was a true fragile colored stone,
I certainly would not use cutters like I'm going to do now.
But this is, you know, on a sapphire or a ruby or a diamond,
some other things that are a little tougher,
I wouldn't have problems with this.
Many people don't think about this,
but the shock involved in cutting, I think, is a little bit dangerous.
So I'll place my finger over top and cut these back to something
as far as a reasonable height.
And I'm going to leave one of them up
because I'm going to show a new cut burr
that is just one of the funnest things that I've seen in a while.
It's just so great.
So I'll leave this one up.
So I cut those back to what I think is an appropriate angle.
I don't like prongs that tower or even anywhere close to tower
over top of the table at this size stone.
This is a six millimeter, three quarters of a carat stone.
So for that, normally my prong tips are somewhere close
to 70 or 80 percent of the overall crown from girdle up.
So right here, that's about where we are right now.
Get a little bit lower as we clip it.
So going into finishing this up,
I want to show you something that's just really fun.
This is a new product by Bush,
and these are called the Twin Cut Cut Burr.
So most cut burrs have teeth inside
that are similar to any of the heart burrs or setting burrs.
They have a fantail array of teeth, okay?
And those cuttings stay packed inside the cup.
It leads to clogging.
It doesn't cut very efficient.
This twin cut is a burr that just has two slots in it.
And I have to admit, when I first looked at it,
I went, I can't see where this is going to be very effective.
The thing that I just demonstrated in clipping the prongs
for a lot of prong situations that would be,
let's say, not as tall as this,
I wouldn't reach for the file.
I wouldn't reach for the clippers.
I would actually reach for this now
because this actually pulls metal off at a very fast rate.
Does not have to be run fast for the burr.
So let's take a look at this.
So here's the cut burr.
And after I get a little bit of lube off of it,
let's watch what this is doing.
I want you to see the spirals coming out of that.
I can back that up a little bit.
It's just these, it looks like the best drill bit spirals
that you'll ever see come out.
And it shortens the prong down right before your very eyes
in a very efficient manner.
So this has to be rotated a little bit.
I'm going to get a little smaller burr.
It's a little bit big.
How do you size the burr up?
Well, in many cases, you know,
you kind of look at it like a baseball cap
that you put on your head.
If you size it up, if it was a child's cap,
you would immediately look at it and know it wouldn't fit.
These sizes are really, really close.
So they give you, they don't pin you in.
There's a lot of versatility here.
So in rounding a prong,
it's good to kind of rotate a little bit.
But this brought a prong
that needed to be cut down, down in just seconds.
I'm going to demonstrate it again
with a different version of this burr.
They have a very slim line version of it that's combed.
So that works terrific.
Gives you a nice round top.
Pulls it down to a good height.
I'll touch one across from it, right next to it.
It happens, when you go to use these,
if you're new to them,
you'll have to use them slow and very,
just really take your time
because it is amazing how quick this thing goes.
So what I'm saying about take your time
with pressure and speed until you get to know it.
When you get to know it, you'll fall in love with them.
They're just one of the best new tools I've seen, okay?
So you might notice just a little of an overhang on the one,
the one that was taller.
I didn't shorten it all the way down.
There's just a little say, you know,
place where hair might catch or something like that.
So I want to show you a little tricks on this.
Many times the answer is not always
to reach for something to remove,
but it's actually to kind of burnish down that edge
is the better way to go in most cases.
I'll show how to make this tool coming up.
This is one of my favorite little tricks.
It's called a micro needle burnisher.
So it's nowhere near as,
it's much more sharper than the needle burnisher
used for flush setting.
So if you were to look at this burnisher against something that's,
this is a GRS rubber handle.
This is more like a needle point.
This is really super, super sharp.
Does some really neat things.
One of the things that I use it for is stuff like this,
breaking these edges down.
As you see that little void right there, okay?
If you use this burnisher,
and if you look at that void as a very,
just a very shallow little thing,
you can burnish that edge down to where that void is now gone.
If you look at the microscopic edge right here,
where it might catch hair,
you can burnish.
So you're, you're burnishing,
you're pulling metal from the hill
and I'm bringing it down towards the edge.
Now, you would not want to do this on a really soft stone.
I would want to be careful.
Let's say if I was working around opal,
I would not, well, here's a piece of opal,
and if I can get this in the shine the right way,
I can touch this, but I,
but if I was to stick this in and pull back,
I would certainly scratch it.
So it becomes a matter of hardness versus pounds per square inch.
This could be a little harder,
but polish and not take a direct super,
you know, sharp needle edge and still be, be fine with it.
So you have to be somewhat cautious with that.
For a, for a real simple explanation of what it's doing,
you can look this way at,
just, just say to take the shank of this.
If I was to scratch something with this,
the, the, the natural thing for many
is to begin to abrade out that scratch
through a sanding stick or a rubber wheel.
And I'll show you some tricks on,
on rubber wheels that help you work on domes,
but the many would start to abrade out
and to remove the upper edge of the metal
to come down to the bottom of the new valley
that was made by the scratch.
But burnishing actually takes the upper edges of the valley
and begins to push them back down
so that now the bottom of the valley begins to somewhat fill in.
And so that burnishing is,
is in effect what's happening to this edge of, of this metal.
It's being burnished instead of removed.
It's, it's being manipulated in that manner.
It's good.
So we've used a different type of cup burn,
some other little tricks,
but none of it's going to leave things perfect
as far as getting it quite ready to polish.
So looking at this prong,
there's some things that I see
where there's a little bit of flashing.
Flashing can be difficult to get with a file,
difficult to get sometimes with a graver
unless it's really, really razor sharp.
And also, you know,
somewhat dangerous to do with some of those,
those tools, especially if it's fragile.
This microneedle burnisher used with a very light touch
can be used around some things that are not,
maybe not as tough as, as sapphire, ruby or diamond,
but it could also be annealed.
And I'll talk about that.
We're going to anneal some tools
that will seriously change the hardness of them.
I'm going to use this little needle point,
just like a sewing needle.
I'm going to use that little needle point
and just lightly take off
that little piece of flash in there.
Just with the, just the lightest of pressure,
you can see cleaned up the majority of that.
The uses for this are, are so many.
So now what I'd like to do is show you a great trick
about cleanup of the prongs themselves,
clean up before polishing.
This can be done with different rubber wheels.
And when I'm using,
when I'm using rubber wheels around something
like even a CZ where I could scratch it easily,
I like to use a silicone pumice.
This is a knife edge silicone pumice wheel.
And it's a great wheel for using right around the sides
and the front edge of this, of this, of the prongs,
especially if this is on something
that is not a very hard stone.
So very light touch.
The, the thinness of these can be pretty thin.
You have to constantly reshape them.
And I'll show you that.
So just a super light touch can be,
I use the knife edge rubber wheel,
mainly around the front of the prong.
And if I didn't have a lot to do in the back,
I might touch it up.
Let me show you this edge.
And it starts to get fat,
even from that light little bit of work.
If you use a diamond dressing stone,
you can pretty easily adapt all rubber wheels
in shapes that you like
by just simply touching them and resharpening.
I'm constantly resharpening my rubber wheels.
So there is a much sharper version again.
One of the, one of the things to keep
from damaging the edge as much as being very delicate.
I think when you get to the front end of a prong,
that's time for it to be delicate.
I want to show you another great trick
for, say, dressing maybe prongs
that may be a little taller, a little heavier,
or in working around stones and working around diamonds.
This is a great trick.
This, this is using an aluminum oxide abrasive
instead of a pumice.
The silicone pumice wheel that I just talked about
has a hardness of, I think, four, 4.5.
So it's considerably under even opal.
Let's take one quick look at that before we move on.
Here's an opal, and you can just run this wheel
directly on that opal, and we're not having any effect.
Opal range is 5 to 6.5,
but pumice is definitely softer in the fours.
So here is a, here is a pencil cylinder rubber wheel.
This is a little chuck that holds this.
This, this is three millimeters in diameter
and comes out and put it in.
Many times you'll, you'll want to take off the cone to get it in.
And then this cone tightens the, the, it's a chuck,
but the, it tightens this thing up so you can,
so you can work with it, okay?
What I'm going to show you today is how to turn this
into a little bit of a cover for, for some prongs.
And it's just a great trick.
So I'm going to take this, and with this diamond dressing stone,
I'm going to turn this down into a cone.
And this will all be specific to, I think, the size of, of what I think I need.
And then I'll use a ball, an older, duller ball burr.
And I'll just take, what I mean is I'm, I'm, I try not to use new ball burrs.
I would use an older ball burr.
This is pretty sharp, but I generally would use older ball burrs.
And I can, while spinning this, this chuckable piece goes in a flex shaft or a micromotor.
While spinning this, I'll by hand apply the ball burr to the end of that.
If I sharpen that too sharp, I would just simply flatten it with the diamond stone
and then come back.
And I'm just going to make a cup.
I don't have to have the exact ball burr all the time because,
as you're going to see here, I'm just going to pull this a little bit
and make it wider.
Now, I want to make sure that I don't pull it all the way out.
And if I do, it's an easy fix.
It's just, this is like, it happens so fast.
Now I've made a little cup.
And if I really have to make a prong look perfect on the top,
I have to be careful about hitting the stone.
But I can take this and come around and put a nice polish, a nice finish.
And these come in a lot of different grits on that prong
in a way that just has less faceting from using something like a knife edge wheel.
I prefer in setting to try to do as much pre-work as possible,
but there are certain times when you're setting something
where you have to clean up afterwards.
You miscalculated, you got to recut a prong and stuff like that.
And this is a great, great little tip, as you can see here.
It just does a really pretty job of rounding those.
Okay, I want to take just a second to elaborate on what some of what you just saw.
Introduced Bush's new cup burr.
This is the coned version as far as the outside is very slimline and tapered.
This can be really nice because it allows you to work around prongs
where another prong might be tight up against what you're presently working on.
This is Bush's new, it's called a twin cut.
There's a lot of burrs out there that I've seen throughout the years,
cup burrs that have slots in them, four slots, one whole slot across.
And this burr is not those.
This is a completely different, brand new technology that's just really,
really outperforms what you would think.
So with just these two slots, I want to show in maybe slower motion
the full effect of the metal spiraling off.
And I'm just going to take this prong down.
As you can see right here, I have a couple of levels
and just want to show you how quick this happens and how efficiently.
Okay, so as I'm working it, I want to take a second to slow
and just see those continual spirals.
That is just optimal cutting when you can cut metal like that
and have it continually flow upwards.
So I'll rock it around a little bit like I normally would be setting a stone.
But if I just sit right here, just watching such a very short duration,
this prong just changed the height of the prong tremendously.
For those of you with older style cup burrs,
I'd like to show you a neat little alteration to them
that can really help you when you don't have the right size
or you're confined into a tight spot.
If you look here by nature, a lot of times the cup burr
gets a little heavy and thick on that front edge.
And that comes from bumping up against stones and so on,
and it gets burnished back.
But this technique I'm going to show you is also for
if the burr is just slightly larger than what you want to use,
you can reduce its size and its accessibility around prongs
by just simply doing this one thing.
As you can see here, the edge is fat.
So I'm going to take this and lay it on its side on a sharpening stone.
And while running it, I'm just going to run back and forth
and begin to bring the side in, making it smaller.
And you can see now that that edge is gone, that burnished edge is gone.
And actually, I'm right there to where the teeth are going to start to
just protrude forward of the leading edge.
That's a great way to make them smaller, make them fit what you need.
One of the next tricks I want to show you is,
is how to deal with something that we've almost all been,
situation we've all been put in.
And that's a broken drill bit in our metal.
When I first started out, I can remember being a little frustrated
by this.
I didn't know how to drill as well and made little mistakes
that caused me to break more drill bits.
One of those is pushing down too hard on the drill bit
and trying to force more out of it than it's able to cut.
That causes the drill bit sometimes to just snap right in half, right in the metal.
And that's what I have here.
I've got, you can see the drill bit and its cross section here
and it's anchored down in the metal.
Can't get it out.
It broke down below the metal surface.
When I first started as a jeweler 30 years ago,
the technique that everybody seemed to say was the thing to do
was to let it sit overnight in alum.
And alum is a acid used for making pickles.
And so it's a mild acid.
And I just found that that was just,
took way too long to have to sit and wait on something
if you were in the middle of a project.
So some years ago, I started using carbide.
And carbide, I did a little testing.
Carbide is so much harder than what most of our drill bits are made from.
And carbide works terrific.
So this is Bush's brand new AU carbide.
This is something they call, it's isometrically centered.
It's a completely different carbide technology
and it's considerably harder than just regular carbide burrs.
I keep some of these around for just these kind of emergencies.
So I'll use a little bit of burr life.
Just a little bit of oil will help.
But you'll begin to see the drill bit just drill up the gray.
The drill bit will just kind of eat right through this.
Part of the trick is, is to stay focused on top of,
centered up on top of the drill bit.
Because the metal around it is so much softer.
So pulling into it, you can see the gray metal coming up.
You'll get to a point where the ball burr sinks in pretty quick.
Depending upon how deep the drill bit is actually broke off in the metal.
This is something you just take your time.
But taking that time is a lot faster than the old methods.
Almost there.
That piece just finally came up in a bigger chunk.
Just a little bit more and I'll be ready to finish drilling.
I normally clear out in a circular motion the bottom of it.
Just to make sure I got everything that's sitting on the side.
You can feel the real difference between what is steel and what is your jewelry metal.
Take a good look.
I've got it.
And now take a new drill bit and finish the hole.
It was that close to the bottom, but really tough to get out.
I'd like to talk to you about a neat little trick that I discovered many years ago.
When I first did my first video, bezel and flush setting.
I was doing a lot of experimentation prior to that on different hardnesses of metals.
So that I could develop some specialty burnishers that would help me
flush set and very cleanly bezel set softer colored stones.
One of the tricks is to just simply anneal regular carbon tool steels.
So what I'm going to show you here in reference to some prong setting is
how to take an older worn file.
And normally that's what I would start with, but this is a mini escapement barrette file.
And I'm going to use it around the prongs for the ring that we had set earlier.
So if that stone was softer in color,
there's always a chance that you could scratch the stone with the file.
That's been the downfall of many a beginner is that in the prong cleanup,
after pushing the prongs over and securing the stone, we end up scratching the stone.
A very simple way to fix this is a simple quick anneal.
So all I'm going to do is put this file on a charcoal block.
And I'm going to take a torch and I'm just going to heat it cherry red.
And I'm not going to keep it there for any real duration.
I'm just going to take it on up and get it nice and hot.
And since I might use the file on a full stroke, I'll take it all the way to the end.
So I'm finally getting the red that I want.
I'll walk that red back.
Doesn't have to be, you know, just full on cherry red.
The effect is, even though in the lighter red, the effect is there.
So I'll show you.
In just a minute, how this doesn't scratch most stones.
So here I have an opal that has been epoxy down to a piece of metal that can be held in a Benchmade.
And I use this opal to demonstrate with a regular file that has not been annealed,
how easy it is just to scratch and damage the stone itself.
You can hear it.
You can see it.
Okay, so now we'll take the annealed file and we'll try to do that.
I want to make sure that you understand that you have to air cool the file when you heat it.
If you were to quench cool it, that would actually make it hard again.
So I annealed it to the light red color and then I just let it simply air cool.
So here with this file that you can see it oxidized and see where
I heated up to right here, the rest of it normal.
And I'll get a nice shiny spot.
I'll just go right.
That's catching in an old scratch, but right here I can push on it and do whatever I want.
Now, pushing at such a concentrated point is dangerous.
It really is.
It's dangerous because, you know, something that might be slightly soft or could damage
just via sheer pounds per square inch pressure.
But let's take the file like this and look at just file directly on top of the opal.
And you can see the burnish mark there clearly indicating that the opal is harder than the stone.
And wherever you file with this, you will get no damage to the opal whatsoever.
It's a really neat way to protect yourself.
So let's put it to a little practical use for a second.
If I wasn't going to use a cup burr and I didn't pre-finish these prongs prior to setting,
I would want to file them.
Well, you might think that annealing the file makes it worthless as far as it's not useful
in filing, but annealed tool steel is still so much harder than just silver and gold
and metals like that.
So you can see here it clearly files and clearly shapes the prong.
Now the file doesn't last as long, but I'll take my worn files and do this so I could
have a softer colored stone and I could be working around that softer colored stone with
this file with pretty good level of safety and not scratching that stone.
Thanks for watching.
I hope you found these tips and tricks to be useful.
Please feel free to reach out to Rio Grande for questions about tools and techniques that
you saw here today.
We'd also like your input and comments on future things that you'd like to see us demonstrate.
Thank you.