Hammer Forging A Silver Cuff Bracelet

Jewelry Making
51 followers
Hi, I'm John Miller from John Miller Design in Yellingup, Western Australia.
We're near Margaret River, we're in the Margaret River region of southwestern Australia, renowned
for its very spectacular surf, very excellent quality wine and a vibrant local artistic community.
John Miller Design is a small boutique jewellery manufacturing business
and we employ about twelve people, about five of them are jewellers at the bench working.
We use old world techniques and specialising in forging, fusing, hammering and making our own
steel punches, of which I now have probably the largest collection in the world, which feature
Australian flora and fauna for the most part. Today I'm going to be showing you how to make
a forged silver bracelet and this is sort of how to do a quickie on it. I've cut this piece off,
a larger piece of six millimetre round silver wire and that's about not quite a quarter of an inch
and I'm going to try and show you how to get through this nice and quick with a big hammer
on a polished steel block. I've polished my steel block, I've given my hammer a bit of a dress so
it's not too grungy and away we go. As we go the metal starts to spread. A long time ago when I
first started doing this, which was 47 years ago, a jeweller told me not to be afraid of the metal
and just give it a good old go. So we've got a spread on one end now, I'm going to hold that
nice and flat the other way and do the same thing on the other. Good, okay I've got my ends to make it
out into a little bit propeller shaped. It's got a bit of a twist in it but we'll sort that out
and now I'm going to go into the middle. Now the more we hammer in one spot the wider it will get
there and also the narrower it will become in cross-section and it's going to go a bit silly.
There's a few rules we have to follow here. I might come around with a slightly rounder profile
hammer. The rule is always be working it back to straight. Rule number one, always be working it
back to straight and what happens is if we beat on one side it will bend around that way so
then we beat on the other side it will straighten it up again. So always be hammering on the inside
of your curve if you've got a curve. You can see it's going a bit banana shape this way
and I want to go take it a little bit that way but if I hammer on the inside of that curve
it will straighten it out again. That's about as far as I want to go
with the big hammer at this stage so I'll change hammers and I'll be right back.
Okay I'm pulling down my profile because I haven't got much curve on here and it's starting
to bite in at the edges so I've got myself a nice polished hammer here with a reasonable round
sort of profile on it, a good sort of radius and the rule is really to always, I'm working on a
nice clean steel block and I'm working with a nice polished hammer. It's a fairly standard ball
peen, common or garden ball peen hammer but I've put a nice polish on it and a final polish with
a product called Steel Bright which is tin oxide and that gives you a really nice shiny hammer.
It's good to dress it up occasionally as you go because it gets a bit pitted and this will give us
in effect a really nice finish so you don't really have to buff it or polish it later
and now I'm just going to keep going. Unfortunately even the best quality steel
will, while you're doing this, will get little pits in it from the hammering and it wouldn't
matter too much except once there's a dozen little pits in it and you keep hammering,
it's a dozen plus a dozen plus a dozen and you end up with thousands of dirty little marks in
there so I'm going to go and polish my hammer again and give it a bit of a final whack on this
steel block before I take it over to a mandrel. Okay now you can see where I've hammered more
in the middle it gets wider. It's got really quite a nice sort of shiny beaten finish on it
with a little bit of ball peen effect and we could make that more exaggerated by using
a sharper peen or we can use a cross peen, any kind of hammer effect we want to put on there
but it's looking pretty good. I've hammered it out more on the end so it's a bit wider.
I've hammered it more in the middle so it's a bit wider there and as you can see it gets thinner.
I've left a little bit of thickness there just so it's got some nice shoulders and now I'm going to
take it over to the mandrel and round it up. Okay here's some steel mandrels that I've had made
for me at the local machine service and this is high carbon steel. It's not too expensive
and mild steel tends to be a bit dirty and grey and lifts off onto what you're working on
so I don't use those ones anymore. I like my high carbon steel mandrels they don't need to be
tempered because otherwise you damage your hammers on them so they're still soft essentially
and I've had these angle iron brackets put on them so that you can set them up in a vise and
most of the commercial ones you buy you can't set up in a vise you've got to hold it in your hand
and it makes life really difficult so we can set this up beautifully like that for us.
Makes a sensational anvil for working on and now I'm just going to belt this thing around.
This is a dead blow hammer which is good because it doesn't bounce.
Working with pretty thick metal like this it can actually jar your handle up while you're
whacking it on there so if that's a problem you can just hold it in a rag and then doesn't hurt
you so much. Double bending it you can always get yourself a wooden v-block like this and
set it up in there and just whack it down in there to get a good sort of curve in it.
Makes life easier and you don't hurt yourself so much. Now I'll get it back onto the mandrel
and we'll continue as before. I'm always keeping it clean by the way as I'm working.
As I bend this around it starts to stretch on the outside and it gets a bit matte goes to a
sort of satin finish with little stretch marks and nobody likes stretch marks and so I want to
get this hammer back onto it. Also it's really quite small it looked big but it isn't
and that's because although it was about 145 millimeters you have to factor the thickness
of the metal into the size that's really important so you've got to add pi times the
thickness of the metal to the length of it when you measure it so it is actually quite small
so I'm going to give it one more beat which will give it a really nice finish
and get it out to a nice finished product hopefully and I need to find the right place
to work it on the mandrel so where I want a tight curve I'm down where I want a broader curve I'm up
there is a tendency to start thinking about last night's Netflix show or daydream while
you're doing this and you really do have to concentrate and stay with it it doesn't take
too long it will tend to drift and get a bit twisted and you need to always be straightening
it back up again by hammering on the inside of the curve so this is coming over this way
when you hammer on that side and push back that way there's no end to what you can do
with a hammer and a piece of gold or silver or copper here's a few that I've made that's
nearly finished that's a a triskel that's three three faces with a cross plane hammer
that started out like that and got up to about there they will get bigger as you work them
that's another one that's chasing itself around that beaten finish is your finish you really only
need to give it a quick rouge after that if your hammer's if your hammer's nice and polished
and you come up with a great product
