How to Make a Pumpkin Pendant with Stone | Intermediate Level Wire Wrapping Tutorial

Jewelry Making
51 followers
Hey guys, Jocelyn here with Fantasia Elegance. In this tutorial I'll be showing you how to make
this very cute wire wrapped pumpkin pendant which does encase a stone. This may look familiar to you
if you've seen my previous pumpkin pendant tutorial I did without the stone. If you've
done that you'll certainly have a leg up on this. But it's a little bit different,
it does add some more wires again to encase this stone for us and it's shaped a little
bit differently. You will of course need a cabochon to make this. I will be using a 22
by 30 millimeter oval cabochon. This is Regalite which I got off of Etsy, that's where I buy most
of my stones for those of you who are curious. I will see if I can find a link to something
similar that would work and leave that in the description section below if you need help
finding a stone. As far as wire goes we're going to be using two different types. I will be using
some 18 gauge round wire and some 20 gauge half round wire. You can use as well instead of the 18
gauge round you can use 20 gauge square. That makes it a little easier to bind everything
together but it will affect the look slightly. I prefer the round wire personally but of course
you can use either. And I very much like the copper look since we are doing a pumpkin. I
think the orange color is very nice. So again I got my copper wire off of RioGrande.com.
They don't pay me anything, they really should, but everyone always asks where I get my wire so
that's why I tell you guys. As always I have in the description section below a list of the exact
tools and materials I'm using and where you can get them. You might need to click that little show
more button in order to expand it and see it. So to start out you're going to want four pieces of
that 18 gauge round wire or if you're using the 20 gauge square wire. We're going to cut four
different pieces. We're going to cut two that are nine inches long, we're going to cut one piece
that is 10 inches long, and then finally one piece that is eight inches long. And the reason I have
them laid out like this with the nine inch pieces, then the 10 inch piece, and the eight inch piece
is because that's going to be the order that we wrap these in around our stone. So if you
take a look at this completed piece here, we're going to bind all three of these wires together
in the center middle and then we're going to wrap them up and around the stone. So these two nine
inch pieces are going to go on top of the stone, the eight inch piece we will use to make the back
encasing the stone. So that's kind of where we're going with all these pieces of wire. So like I
said we're going to bind these together in the middle. So to do that we're going to cut a little
piece of our half round wire. So I'll be cutting about a three inch piece of this half round wire
and then I'm just going to kind of pre-bend this into a little u-shape using my tweezer nose
pliers here. And then we want to do is take all our wires and I'm going to arrange them so that
the centers are together. So again we want our two nine inch pieces on top, then we want our
10 inch piece, and then we have our eight inch piece. And if you can see I'm just eyeballing
this arranging them so there's kind of equal distances on the ends on both sides so that I
know I'm kind of getting the centers of all these wires. And then I'm going to nest them all together
next to each other. And this is where having them out of square wire is a little bit easier, they
just stack more nicely and are easier to connect. But I'm just eyeballing where the center line is
going to be here. You can of course mark it on your ruler if you want. And I'm going to drop that
little u-shaped binding piece onto where I have eyeballed the center is. And then I'm going to
squeeze that on down and just start binding this all together by wrapping my wire around.
And of course you want the flat side of your half round wire to be against all these wires.
So I'm going to place two wraps going all the way around all the wires. And then if you can see here
because of how we have these wires bundling up to go around the pumpkin, I just have the binding
wire going around the top wire twice. So what we're going to do is take that top wire
and bend it up a little bit to get it out of the way. I'm going to take both ends of that and bend
it up. And then I'm going to wrap the tails of my binding wire around the remaining three
frame wires. I'm just going to go once around the bottom three wires. And then similarly I'm going
to take the next top wire, bend it up, bend both of those tails up to get them out of the way.
And then as before I'm going to take the tails of my binding wire and go around just the bottom
two wires now. And I'm going to use my tweezer nose pliers to really snug these up against the
previous wraps we've made. It can be a little hard to work it up into that space there,
but that's what we want to do. And you can do either one or two wraps here depending on how
secure you want it to be. I think I will do two wraps. And we want to end our wire tail on the
inside where it's going to sit up against the stone so that it won't be free to scratch on
anybody's skin or clothing. All right, so once we've got all our bindings done, like I said we're
going to snip off these ends on the side that will be sitting against our stone. And then you can use
your chain nose pliers to make sure that's pushed up against those wires. Do that on both sides here
and tightening that down as much as we can. So what we're going to do first is use these bottom
two wires and we're going to wrap them around our cabochon to form that frame. So it might work well
for you, you can set your cabochon on a flat surface and then lay the wires over top of it
and push them around. It might work better for you to hold it up in the air. You can kind of play
around with what works well for you, but I'm just going to center this wrapping on the center of our
stone, on the wider center, and just wrap these around keeping them nice and close to the stone.
All right, so after you've got that shaped around your stone like so, and we don't want it sitting
right up against the stone, you want just a little bit of space around the edges like so,
what we're going to do then is mark the point where these two sets of tails for the frame wires
cross over each other kind of at the center top. I'm going to take first one set and then the other
set of tails and just bend it straight up where they cross over. So I'm going to kind of mark the
center spot there with a fingernail. I'm going to bend first the back set of wires up and then we
will do this other set of wires here. Okay, so that's what we have now. At this point, we're
going to go ahead and shape the rest of our wires, these kind of two looser ones on top that we
didn't bind as much at the bottom. So to do that, I'm going to place my stone on a flat surface.
I will lay the frame over it and push that frame down so it's as low as it'll go touching my flat
surface. And then I'm going to bend these two sets of wires into our little center pumpkin
shapes. I'm going to push them down against the stone so they have this curve that direction as
well as this curve vertically. So I'm going to start with the innermost wire doing that smallest
shape. I'm going to start by putting a little bit of a curve in here, bending the two tails curving
over towards the center so they're going to cross. And you can use either your fingers or a tool to
do this, whatever works well for you. And then once we have that rough shape in, you can kind of
push it down onto the stone so that, as you can see, we're now getting that kind of bend for the
shape of the stone in. And we're going to do the same thing with this other
pair. And what you can do for shaping this is kind of go halfway between the inner one that
we have and the outer frame. So that's what we're going for with the kind of placement of those.
So let me start putting in a gentle bend on these tails as well. Do that on both sides.
And then once I've gotten kind of the rough shape in, I will again lay it over our stone,
do the same thing, again pushing those down to get that bend in that we want. Okay, now this is
all kind of loosely connected at this point, so don't panic. This is going to firm up as we finish
the top portions. So let's move on to do that now. And I am periodically checking because this isn't
as tight as I'd like it to be, this bottom binding. I'm just making sure it's staying centered
underneath where all our top wires meet together. Okay, so now we're going to do the same thing with
these tails for the inner curves that we made, just bending them all so they are going straight
up together and staying stacked on top of each other. So let me go ahead and just refine this
a little bit so that we have our tails crossing over nicely all at the same point. And then as
before, I'm going to take the wires, mark the center spot, and bend them up.
So now you should have something like this where all of our wires are meeting at this center point.
They're kind of all stacked on top of each other, maintaining our order that we had them in.
And now we're going to put in a temporary binding, connecting all of these pieces.
So since it is temporary, we don't have to use an exact length of wire,
but I will cut about a three inch piece here of our 20 gauge half round wire. Let me go ahead and
get that cut. And again, this is going to be just a temporary binding just to make it a little bit
easier to work with and do what we need to do before we put our final finishing piece in. So
I'm just bending this piece in half like we usually do when we're doing a binding,
and I'm going to drop it over top of where all these wires come together. I'm going to cross
these tails on the back. I'm going to put several wraps in, connecting this all together. And if you
can see, again, I'm keeping my wires stacked. So I have like a long stack this way, and then it's
just too deep from this direction. Okay, so that's what we have now. And we're going to do a permanent
binding on both sides, kind of the center line sides of this little pumpkin. So again, taking
our half round wire, I'm going to cut some shorter pieces this time. We don't need a ton. A two inch
piece should be plenty. Two inches there, and we'll do two of those. I'm going to put a little,
as per the usual, a little U-shaped bend in both of those. Just going to take one for now. I'm going
to place it again on that center side spot, going around just these two frame wires, and then
binding that very tightly. I'm going to place four wraps in. You can do more or less. I feel like four
looks like a good amount, holds it sturdily without being too chunky on the side and detracting from
our design. And I'm going to hide the tails on the inside, where they will be sitting against the
stone. So I'm cutting just enough that I can wrap it around towards the inside. We'll do the same
thing with the other tail. And then we'll do the same thing on the other side, so it's symmetrical.
So taking our other piece of half round wire there, going to position it again on that center midline,
and we will wrap that once again very tightly around. All right, so this is what we have now.
We have our bindings at the center, the sides, and the temporary one on the top here, and we can
double check our stone is still fitting inside. So now we can move on to the next step, which is
encasing our stone here by bending the back wires in. And we're going to do that by flipping around
to the back here. I'm going to take just the backmost single wire. So if you view this from
the side, you can see there's those two wires going all the way around the stone. I'm going to
separate those out ever so slightly so that we can manipulate just this one back wire. And we're
going to put in four little kind of inward divots to encase that stone. Okay, so I'm just going to
take my chain nose pliers, again, separating those wires out a little bit so I can grab it.
I'm going to bend in just the center of it over top of our stone here. Okay, so we're getting that
kind of shape, and we're going to go around doing that on each each middle portion between our
bindings. All right, so let me pop out this wire here a little bit. You might need to wiggle your
little side bindings. If they have moved on you, you want to make sure they're still
centered on kind of the four quadrants. All right, but just divoting in in the center there.
You can kind of reverse and go at it from the other side as well to make sure it's creating a
symmetrical centered divot there. So now all we have to do, all we have to do, is finish all these
wires on top. Now we're going to use them to make all these little decorative swirls as well as the
veil that our chain will go through. So to make that a little bit easier, I'm going to split all
these wires right down the center. So if you have them still lined up in their little orderly rows,
that will make it easier. But I'm going to take the four on the left, and I'm going to bend them
to the left a little bit. I'm going to take just the top two wires on both sides and bend them a
little further out even to get us even more space to work with here. And then the third,
these longer of our two back wires, we're going to use to make the veil. So I'm going to run these
right next to each other like that, and then we're going to wrap this with our half round wire. If
you can see here, our veil has this wrapped wire around it. So we're going to do that now. I'm going
to take a fairly long piece of our half round wire. Let's say a 10 inch piece should be sufficient
for us, I think. So we'll go ahead and cut that. And then I'm going to take a little bit of a tail
here so I can hang on to it more easily. I'm going to bend these two long veil wires forward
to get us a little wiggle room from these back two wires. And then we're just going to start
wrapping this around both of those wires we're going to use for the veil. And I'm going to push
this so it goes all the way down into this crack here where all of the wires meet each other.
All right, I'm just going to keep wrapping, placing each wrap nice and tight next to the
of course with the flat portion of our half round wire up against those two 18 gauge wires.
And every few wraps, I'm just going to take my chain nose pliers
and tighten that down. I'm going to keep wrapping that until we have about an inch here of our
wrapped length. And again, we've bent that forward. And now to form our little veil,
we're going to loop it around towards the back. Okay, so you can use if you have bail pliers,
that would work well. If you have like a narrow handled thing like a paintbrush or something,
you could use that as your round shape. I'm just going to use my round nose pliers and start
bending our bail around towards the back here. And you don't need to have an enormous bail for
this. I might even wind up unwrapping a little bit of what I have wrapped here. I'm just going
to bend that around till we have a little loop headed towards the back. And let me see on my
example once that's going to be a bit shorter. So we're going for if you measure from the bottom of
the pendant to the top of the bail just to kind of get your bail size in line, it's going to be
about one and three quarter a little less one and three quarters inches tall there. So I'm going to
shorten my bail up a little bit. Let me make sure this is running kind of more straight. If we look
at it from the front, we'd want it to be straight and not all funnily off to the side. So I am going
to unwrap just a few wraps here from what I did with my half round wire. And then I'm going to
continue forming this little teardrop shape here for our bail. And you might find it easy to take
these two ends here and kick them out slightly away from the stone just a little bit so that you
can bring this all the way around and meet it with our other sets of wires that we have. So once you're
happy with the shape of your bail, it's now time to actually undo this temporary binding we had
and replace it with this longer tail that we just used to wrap our bail. I'm going to do this kind
of a little bit at a time so that we don't have these all just spring apart and come undone.
So I'm going to undo one wrap from the temporary binding, replace it with a wrap from our bail wire,
etc. So let me pull out my tweezer nose pliers to do that. So I'm going to grab that temporary
binding wire. I'm going to undo it one wrap. I'm going to take the wire coming from the bail. I'm
going to wrap it very tightly right around where that wire just was that we undid. And I'm going to
continue that going all the way down. Okay, and to finish that wire off, I'm just going to take it
onto the side here and snip it off on the side kind of towards the back. And we will be wrapping
some tails around it and that will help hold it into place. But I will use my tweezer nose
pliers to push it on down and secure that into place. And we can do the same or similar thing
with this other end of it. For this one, I'm going to wrap it onto the inside of the bail.
If you can see what I'm doing, I'm going to put it inside that space right there.
So let me cut just enough of it that I can push it onto the inside of our bail. And again,
I will use my little tweezer nose pliers here to smoosh it down against those bail wires.
All right, so we finished off all of our half round wire at this point. Let's go ahead and
deal with some of these shorter tails we have on the back. I'm going to take these two that are
heading upwards, and I'm just going to wrap these straight down and around pretty tightly towards
the bail. And we're going to make some little tiny loops on the back here. If you can see,
that's what we're going for, just those little loops, just to get these a little bit out of the
and finished off. So I'm going to wrap them around until the end is crossing over the center line
there. And then I will snip right there with my flush cutters. And I will take my tweezer nose
pliers, put just a little bit more of a bend in the very tip of that wire, just to make sure it's
heading in towards where it will be touching another wire so that we don't have any issues
with it being scratchy or catching on people's clothing or anything like that. And we'll do the
same thing on the other side, bending this in, doing a little snip there, cut the end off,
and then wrapping that end, curving it a little bit more. Then I'm just going to squeeze over top
of both of those, push them towards each other towards the center line. And then if we view this
from the side, you can see how they're kind of pointing that way towards the back. I'm just going
to make them head vertically instead. So pushing those back in a little bit, just like that. Okay,
and then we're going to do the same thing with these two wires heading down, except they will
be going from the opposite direction. So I'm going to swoop these up this time and kind of layer them
over those other ones that we just finished off, so that when you view this from the front, it just
looks like there's one wire on each side. And I will push that down right up against the
previous one we just finished, making sure the shape is the same, so that again, if we look at
that from the front, you just see the one little arch there. Okay, same thing on the other side,
wrapping this up and around. Okay, so we have now finished half of our wires. We've made really good
progress here. Now all we have to do is put in these decorative swirls, which is the fun part,
and we're going to use these two sets of wires to do that. So let's go ahead and do the right-hand
set first. We're going to use those to make these kind of larger swirls that go up and over the bail.
You can see there. So I'm just going to get these left-hand ones a little more out of the way by
bending them over. Then I'm going to work with both of these right-hand wires held together,
and I'm going to put a little swoop in over the bail, heading left. I'm just going to use my
fingers to shape this. I'm going to put my thumb on top over the bail and over the wires. I'm going
to use my left hand to provide a little tension here, and I'm just going to start bending these
over in a swirling motion over top of our bail. I keep going all the way around,
and we're going to put a second little loopy loop in so the wires go over top of each other there
like that. There's the second little loop I'm talking about. So again, using my thumb to kind
of hold things in position, swooping these wires around, all the way around to create a second
little swirl over top there. All right, and then I'm going to take this longer wire of ours and
put a little decorative loop in just this longer wire. So using my round-nose pliers,
I'm going to grip kind of near to the bail, just wrap this all the way around to create another
little loopy loop right here that will sit close to the stone, just like that. I will make that a
little bit smaller with my chain-nose pliers. So we have something like that now. I think I'm
actually going to bring this swirl a little bit up more to hide some of those bindings at the
center. I think that might look a little bit better. So I'm going to move that up just a
little bit and then unswirl this tail a smidgen. So now we get to finish these off. I'm going to
swirl both of these into open spirals going this way down towards the stone. So I'm going to take
the longer one first and just grip right on the end with my round-nose pliers and start putting in
a tight open spiral here. And then we have this shorter wire that we're going to do the same thing
with. I'm first going to bend it up this way a little bit so that it's running next to that
little loopy loop we made right there, and then I'm going to put a smaller open spiral on this one.
So that's what it's looking like now. You can tweak these a little bit to get them sitting
right where you want. If you want them closer to the center of the stone or further to the sides,
that's largely up to you. I'm going to get mine a little closer to the center of the stone there.
And you can leave these how they are. I like to kind of secure mine down with some little bindings
if you can see here. I just connected them to our frame wire to make sure they're not, you know,
going to catch on something and deform a little bit. So let me go ahead and do that real quick.
I will pull out my half round wire, cut a short little length of this. We don't need very much,
this is probably two inches or so. And then I will pick a spot where everything's overlapping.
So I'm going to go over both of those swirls center line and through our frame wire
and just wrap this around to secure. I'm going to go once around the little swirls and then I will
wrap a few times around just our frame wire and this right hand swirl to secure our binding wire.
And you can kind of play this by ear based on where things are falling for you or
just where you think it would look good to have this wire sitting. And then you can finish it off
just giving yourself enough length that you can kind of tuck it towards the inside towards the
stone so there's no loose wire bits. And now that is securing those little side swirls for us. So
we're going to do some not identical but complementary little swirls on the other side
with our other two wires. I'm going to put some swirls lower down closer to the stone.
So again, working with these as a set of wires, I'm taking them both at once, I'm going to put a
little loop in right here. You can see on our example piece, we're putting that little loop
in right there. So kind of similar as before, I'm just going to wrap them around, keeping the wires
together, going all the way around. I'm going to adjust how this is sitting using my chain nose
pliers a little bit here so that we have something like that. Now I'm going to take this
lower wire that is forming the inside of our little spiral, and I'm actually going to snip off
so that this is ending right at the edge of that spiral. And we're going to hide the end of this
wire there in the spiral. So I'm going to cut it right there inside that little spiral we just made,
just that inner wire, and then I will use the tweezer nose pliers here to kind of take the
tip of that, push it down inside the spiral we formed, kind of hide that end for us.
Okay, and then I will take this one remaining tail we have and form another little open spiral
on the other side here. And I have more length than I need, so what I'm going to do is take my
round nose pliers, position them kind of where I want this spiral to be, and start wrapping it at
that point. And once you get a sense for where it's going to sit and how much wire you're going
to need, you can snip off the excess and of course refine the shape as needed. And same thing as on
the other side, once you're happy with where that's all sitting, I'm going to find a spot
where it intersects with my edge wire and I'm going to put one simple little binding in there
with our half round wire, just to hold that on. So that is our little pumpkin pendant design. As
you can see here, this is the bright copper. It's very pretty and very fall appropriate.
You can also, if you prefer the look, pre-antique this. I do have tutorials on my channel for how
you can antique copper using liver of silver. That's the method I used on this one. So you
can check that out if you prefer this pre-antique look. But if not, you can just leave this as it is.
You'll either need to clean it regularly or it will, over time, look like this one on the left.
So I hope you guys enjoyed this tutorial, found it helpful and easy to follow. Feel free to comment
below if you enjoyed it, if you had any questions along the way. And please subscribe if you are not
already and you're interested in more tutorials like this. I do have more planned. So you can
hit that subscribe button, hit the bell so you get notified when I upload new videos.
I hope y'all are doing really well. I will see you in the next video. Until then, happy crafting.
