Carving a Wooden Bison with Just a Dremel

Nghệ thuật chạm khắc gỗ
6 followers
Hi guys, so I recently carved a bison and I wanted to make another so that I could have one for
myself and I thought it'd be cool to film a video showing kind of the step-by-step in case anybody
wants to follow along and make one for themselves. So I'm starting out with a block of wood here,
it's about three inches by two and a half by one and a half. I chose to layer three pieces,
this is wenge in the middle and then padauk on top and bottom. You can just use one piece,
I like these woods because they're really colorful but also really hard,
I don't think anything's going to break off. So other woods, if you have them, white oak, walnut,
purpleheart, poplar, maybe luan, those are all good ones that I've worked with that I think will
not break on you. I would avoid using any sort of like dumpster stuff that you'd find at
Home Depot or Lowe's because a lot of it's going to be pine like this and in my experience
between these lines it's really soft and then the line itself is really hard
and it makes it just difficult to get good detail and also cut where you want.
So anyways, we're going to start with drawing your design. So here I have the bison,
pretty much takes up the whole block of wood and then exactly the same thing on the back,
makes it a lot easier if you have it on both sides. And we're going to start with cutting
out the 2d shape, so not rounding anything off, we're just taking off these outside bits. I'm
multi-purpose cutting bit, the 561. I have a Dremel 4300, any variable speed Dremel
or rotary tool is going to work well, but by default when I'm cutting wood I'll usually set
it to about 20,000 rpm. So we'll start there. Alright, so we're at the point where we have a
rough 2d shape here. I'm going to go ahead and mark where I want the feet. I'm going to have
the front feet a little bit wider, so we're going to come in a little bit,
that'll be about what the foot is, and then I'll have the other ones, the back feet,
a little closer, about there. Now I'm going to use the 561 cutting bit still
and start to roughly shape this. So I'm going to, still at 20,000 rpm,
go right to left as I'm carving. Horns here are going to stick out, so I'm going to avoid
that section, not get too close. Especially with this, because it's pretty aggressive,
it might snap the wood off for a thin piece. So we're very roughly rounded out here.
I went between the legs, got around the outside, left the horns alone,
and I'm going to switch from the 561 to one of these sort of regular cutting bits,
off-brand. I prefer these cutting bits over something that carves through sort of just
grinding it, like a cut saw burr here, because once you finish carving, this one's going to
leave it a lot smoother, which really cuts down the amount of time you have to spend sanding.
Before I start carving, I made this stencil, and I'm going to outline the bison again,
just to give myself some guidelines, and then smooth it out as much as I can with this.
Round it off a little more. I'm going to put lines roughly where I want the legs to go,
as a reference. So I'm up here, bring the knee in a little like so. I think it's super helpful to
give yourself little guidelines as you go. That's symmetrical. So now I'm going to go
between these lines, give the legs a little definition, and then down around the neck,
and clear out some of the stomach. We're just over an hour into the process.
Good time to stop, take a little break, evaluate what you've got going here.
Pretty much got it around the neck. It's very squared off on the limbs here.
So the next thing I'm going to do is use the same cutter that we've been using,
and round around the legs, any of these sharp edges. And then as I'm doing that, I'm also going
to make these grooves deeper to give the legs a little definition, and then I'm going to round
this off, and then we'll see where we're at. Now's a great time to stop, have coffee,
let your hands rest. Wonderful. All right, let's get back to it.
We've left the horns alone, rounded out the legs,
have a little nub of a tail there. I want the entire thing to be thinner,
so I'm going to go back to the 561, and I'm going to carve like this along here
to get more of a spine, and then also just to narrow the body a bit.
So just use the 561, it's about the right shape that I like. So now I'm going to switch
to this cutting bit, and I'm going to use the side to smooth this out, and then also the tip
to get around the horns here and deepen that groove so that we can file the horns down.
As you can see, I used this bit to sort of shape the horns, but not too thin. We're going to move
in next with a smaller engraving piece like this to really shape the horns as thin as you want
them. And then I'm also going to continue with this bit to smooth out remaining sharp edges,
and then also round out this forehead. So it's roughly shaped, and we're going to add the fur
texture now. I'm going to use something like this, a cutting piece that has a flat top,
so you get this sort of 90 degree angle or less. And then you're going to hit it on the corner,
sort of at a 45 degree angle, and plunge it in to get the right size line that you want.
I put these reference lines. I'm going to do everything on the front side,
fur excluding the mouth. We're going to make these marks all along here.
So here we are, added all the texturing, avoiding the mouth, stopping at this line.
I'm going to move to this cutting bit. And because the fur, this texture, is supposed to be
kind of bulkier than the rest of the fur, I'm going to come in at about
maybe an eighth of an inch deep around this line through the stomach.
And then I'm also going to do the same thing around the mouth. And then while I'm at it,
I'm going to cut around the hooves to make them a little bit thinner than the rest of the body.
We're pretty much all done with carving. We have the texture. We've brought this down a bit.
It's fairly smooth. So now we're going to sand. I'm going to use a sanding drum and a sanding disc
for the smooth parts along with the horns. And then I'm going to move on and cover the entire
thing with these sort of buffing wheels starting from like 180 grit up to probably 320. At this
stage, you can hand sand the entire thing if you want. I'm just going to be lazy and use these.
And we're going to bring the Dremel down to about 8,000 rpm. We're all sanded down. There's a step
that I forgot about, which is the eyes. So I'm going to go back to this piece and I'm going to
hit it at an angle like that so that the top of the eye is flat and the bottom is the curve.
And then in that hole, I'm going to just plunge in this engraving bit
to make the little sphere for the eye. Here are the eyes. I've sanded it as much as I want to.
And we're at my favorite step of the process,
oiling. I would normally probably use a mixture of oil and beeswax if this was all smooth just
so it's nice and shiny. But because of this texture, I don't want the beeswax to collect
in the little notches. So I'm just going to use a little bit of lemon oil. You could probably use
whatever oil you have. I used to use mineral. I can't tell the difference. And just add a little
bit. You really see the color pop of the wood. Don't add too much oil because otherwise it's
going to absorb and then it's going to start kind of seeping out. So I'm just putting enough
to cover it. And then I'll let it sit for a few minutes and then wipe off any excess.
And then you're all set. Here we are with the finished product. There's still a little bit
oil on there, but that's okay. I think this is a great beginner's project because it's
fairly simple. There's only a handful of accessories you need, most of which are
already included with the Dremel. It took about four and a half hours. The first one took around
six. And now it's ready to either be a gift or just take up space on a shelf somewhere.
Hope you guys enjoyed. If you have any questions or comments, let me know.
And if you decide to make one for yourself, good luck!
