How to Make Wood Rings With a Dremel

Nghệ thuật chạm khắc gỗ
6 followers
Hey guys, I figured I would film a video on how I make rings with a Dremel. So I'm starting with
this piece of maple here. It's nine millimeters thick. I'm actually gonna keep that thickness
for the final ring. And then I drew on the size that I need, so it's 17 and a half millimeters
in the center. I'm giving myself around three millimeters for the thickness of the ring.
And I'm going to start with this tile cutting bit to bore out the center. And then I'm going
to move on with a sanding drum. I'll probably use this first, then move on with the sanding drum
to get the center hole exactly how large I want it before I cut out the outside of the ring.
I'm starting at 20,000 rpm. All right, so we've used the cutting bit to get a fairly close
cut around this center circle that I put. And it's just big enough to fit this sanding drum
inside of it. This is a fairly high grit, probably around 400. I'm going to use it just to
smooth out the inside and get as close to that line as I want to.
And then we'll move on to cutting the outside. All right, here we are.
Center's all cut out. It's the right width that I need. So now I'm going to go in with the
cutting bit and cut around the ring fairly close, and then get a flat cut with the side of this
cutting bit around it so that it's fairly smooth. And then I'll show you the next step.
Here we are. The ring is fairly thin. See that? And then this step is pretty cool.
I learned it off YouTube. We're going to mount the ring like this so that we're essentially
turning the Dremel into a mini lathe so you can get a symmetrical sand. Because,
as you can see, it's not perfectly round. There's bits that bulge, bits that are higher.
We're going to mount it onto a sanding drum. And then with the sanding drum, you get some tape,
and you wrap it as much as you need to until the ring fits on there super snugly so that it won't
twist. It'll stay mounted to this as it's spinning.
And then, yeah, this will act as a lathe. It'll spin. And then you hold the sandpaper on there
as it's spinning. The reason I have a glove on is because it gets pretty hot
just from the friction. So I'll show you. It drops down to 9,000 RPM.
All right, check this out. So pretty thin, but it's wonky. See that? It's a little
lower on this side, higher on this side. I'm going to go ahead and try to
use a pencil and spin it at like 5,000 RPM just to mark because I got to fix that.
So let's see. Yeah, see how it's only on this side? Because this side's thicker.
Maybe I should get a lathe. Whatever, we'll see what we can do, you know? All right,
I'm going to take this off the rig, and I'm going to cut that excess off. Just get it flat.
Okay, so it's about as thin as I want to get it. It fits pretty well on my pinky, but I just,
I don't know why it's not... You see that on the top on the left here? How it bulges out?
That's so strange. I've never had that before. It's just not cooperating. So I'm just going to
flatten it out on the top and the bottom by hand, either just on a flat surface, or
I might use this circular sanding disc to just kind of place it on there like that.
Until it's flat, I'll just eyeball it. Yeah, we'll see. I'm actually, I'm going to make
three rings, including this one, but the same method. So I'm just going to cover that
on a time-lapse. So I have this one. It's glued, these four sections. Do it right in the middle
so that it's a little like, it's in quarters, the design. And then this one, it's one inch.
I'm fairly sure if I do the ring like this, it'll be stronger than like this. So I'm gonna
do the hard way and cut out a section like that, and then we'll get to the final sanding.
All right, I moved inside because it's dark out now. The rings are coming along.
These two are for the same person, and this is for another person. This person wanted them beveled,
so it's going to be rounded on the edges here, sort of like a more classic ring.
And these two, the lady wanted them
more flat, so it's not going to be beveled. I'm going to try my best to keep the edge straight.
I'm gonna use this cutting bit to get these two about this thin, and then I'm going to mount them
onto a sanding drum with enough tape so that it's snug.
And then start at 100 grit, down to 220, and then we'll finish up the sanding.
Oh yeah!
Nice. All right, so we have these pretty darn thin. I actually, I'm not going to take it any
thinner because I'm nervous that they're just going to get too weak. You know, solid wood rings by
nature probably won't last too long, you know, you'll snap it eventually. But, you know, I'm
hopefully this thickness will last a little while. They're fairly smooth. These are down to 220 grit,
but as you can see, especially on this one, it's kind of rough on the edges, on the inside.
There's definitely some marks from the sandpaper, so I'm going to use buffing wheels.
I'm going to start at 180 grit. It's not really 180 grit, I think it's a bit higher.
Do a quick pass on each of them, and then to the 400 grit, and then make sure it's as smooth as I
want it. Here we are. These are fully sanded up to 400 grit, super smooth. These two are
kept straight. This one is beveled. Now we are all set. Just kidding, we're going to oil.
I have a little bit of mineral oil here. This one is supposed to be white. Maple is as white as I
could find. If I put it in the oil, it's going to be a little bit more beige, so I'm not going to
oil it. I'm going to oil these other two though. This one's Wenge, this one's Luan and Padauk.
Anyways, oilings. This is my favorite step of the process. Look at that color.
These are super thin, so they're really not going to need much. Wipe off the excess,
and then let it sit overnight. Then tomorrow, I'm going to
use polyurethane. This is what I'll be using. Four coats. I make these little paper cones,
and then just sit the ring on top, stick it outside, spray it, make sure you get an even
coating, let it dry. I'll show you guys what they look like when they're all done. They're all dry.
Here's the final product. Nice and shiny from the polyurethane. Smooth. Wenge gets this cool
light pattern, but it's still smooth. It's just got a bit of texture. This one came out fairly
well. If you guys choose to make some for yourselves, I'd love to see the final result.
Thanks for watching.
