Woodturning modern art | From raw wood to a masterpiece! Watch as a mahogany bowl is meticulously hand-carved into a beautifully dimpled design. This is woodturning and carving like you've NEVER seen before!
@LagunaTools @WalrusOil @Carterandsontoolworks @remarkablepaper 00:00 Introduction 00:52 Roughing the bowl 01:27 Creating the tenon 02:43 Setting up interior surface 03:01 Designing the layout 04:16 Initial carving 05:31 Hollowing the bowl 06:27 Rotary bit carving 07:58 Cup burrs 13:52 Dyeing with India ink 15:10 Rose engine 17:06 Gilding 20:15 Finishing If you need tools and don't care for Amazon, Northern Tool has free shipping on 10,000+ items every day: https://www.anrdoezrs.net/click-101520748-10375751
Hello everybody, welcome to the channel. My name is Brad, this is Q Branch Woodworks,
and today's project is an eccentric, carved, and gilded bowl.
Now, making a bowl like this requires a little bit of extra planning, so I like to draw things
out visually. So I pick up my trusty Remarkable tablet and start diagramming out what I want to
do. The key here is to get a millimeter accurate representation of your final product. Just
kidding, I suck at drawing. This will have to do. The standard bowl making rules apply. Things like
finding your center and figuring out how to cut off excess wood. What's different, however,
is this point that I'm placing about 3 quarters of an inch from the actual center. I'm going to
be drilling this point and the center hole. As you can see here, this leaves two holes fairly
close to each other. We're going to use the center hole for the initial mounting. This step isn't too
crazy either, I'm just trying to get a nice flat surface on the bottom so that I can start to draw
out where the chucking points will go. Using my trusty dividers, I'm marking out the outer
diameter of my larger chuck. After roughing this diameter in with a parting tool, I'm leaving all
of that material in the center because that will become the tenon for my secondary chucking.
Now I'm flipping the bowl over to complete this sort of pillow shape that I'm going for.
The reason behind the shape will become clear shortly. After a little bit of light sanding,
it's time to flip the bowl back over and use that secondary hole, the one that's a little bit off
center. This will give me the opportunity to create a small tenon within the larger mortise,
which will help me mount the bowl eccentrically. I've now set my dividers to the interior diameter
of my smaller set of chuck jaws. Being careful to stay outside of the line that I set with the
dividers, I'm roughing in this tenon with a parting tool. Just a technical note here, the parting tool
is definitely meant more for end grain orientations than it is for face and side grain work. I can't
say that I recommend this from a safety perspective, but it did work for me in this instance.
Now a quick process that I like to call a sanity check to make sure that I actually
have all of my diameters set properly. Once I'm sure that the chuck and tenons will all
fit and play nicely with each other, I can flip the bowl back around and start to refine the face
just a little bit more. Now the purpose behind this next cut is basically just to refine the
face a little bit more. I want to leave just enough of a flat area that I can still reverse
this thing against the face of the chuck if I need to, but I also want to complete this sort
of pillowy shape that I'm going for. Again, a little light sanding, and then it's time to set
up the Trent Bosch carving stand. Once I get the bowl in the stand, I realize that I don't actually
have a good indication of where I want the interior bowl to be, so I start rethinking the process a
little bit. I actually wind up remounting the bowl and putting a small chalk line on it to make sure
that I know roughly where I want the bowl to be. Since the face is no longer flat, I have to
improvise a little bit. My drawing skills are not improving. I check the concentricity, it looks
close enough, and then I go ahead and demount the bowl again. Now here's where the real artistic
decisions start, and obviously based on my drawing skills this is not my strong suit,
so I started off here with kind of this flowing, angular sort of vibe, and I pretty quickly ditch
this in favor of something a little bit more structured. At this point in the process, I know
the overall effect that I'm going to be looking for, and I know the tools that I'm going to use
to get there, but it's difficult for me to visualize in three dimensions exactly how this
is going to work out, so I think it's fair to say that this is an experimental piece through and
through. What I haven't shown much of in this video is just how much erasing and second guessing
happens at this point in the process, and the reason that I think it makes a lot more sense to
make mistakes here and to back yourself out of them is because the second you start carving,
you're really locked into your design. This piece of wood can still be anything, so I was taking my
time here making sure that I really enjoyed what was actually going down on the piece.
Somewhere right around here, probably in the fourth or fifth iteration of this pencil design,
I kind of figured out what I wanted to do, and it winds up looking a little bit more like
petals. If I had unlimited time, if I got to this point in a project, I would probably put it down,
sleep on it, come back, and check on it later. As it is though, my kids are napping, and I got
to finish this, so here we go. The first cuts with the rotary chisel are always a little nerve-wracking.
At this point, you're firmly committed to whatever your concept is, or at least to the points that
you've already cut with the rotary chisel. I like the rotary chisel for this kind of work because
it makes nice deep cuts. This enables me to get a really 3D effect in the final piece.
You may be able to hear in the audio, but I'm consistently working the rotary chisel back and
forth to keep it from scorching anything. It gets pretty hot at the tip. The trick now is just to
actually is after the rotary chisel work is done. It's starting to come to life, but we're only
about 5% of the way there. Finally though, we get to return to some actual woodturning.
All I want to do in this segment is get deep enough into this bowl that there are no longer
any holes from the woodworm screws left. Here I just want to check the overall shape. I'm looking
for roughly hemispherical. It does not have to be exact. Then a little light sanding, and it's time
to start carving. I'm using a conical carbide bit to remove some of this material. My main strategy
here is to keep the Fordham handpiece more or less vertical, just a few degrees off of straight up and
down. I'm trying to carve down into these valleys and get rid of the very bottom marks made by the
rotary chisel. I found it really difficult to do things like this early on in my turning career for
a couple of reasons. One, not having a good rotary tool can really slow you down. I think it's worth
upgrading from a Dremel or the Ryobi to the Fordham pretty much as soon as you can afford it.
The extra power is really worth it. Second, I hated the idea of carving up a perfectly good bowl.
I was really precious about my work at that point, and it took me a long time to sort of get over it.
At some point though, my mentality sort of switched over from a bowl as being the endpoint to
potentially just another blank canvas, another jumping off point for more work. Now, I tend to
keep all of my old bowls that either don't sell or that I don't want to put on sale because they have
a defect or don't live up to my standards for whatever reason, and sometimes I'll just hack
them up just to see what happens. They make fabulous practice pieces. Now again, from a safety
perspective, holding a bowl like this and just kind of hacking away with a rotary tool is probably not
the smartest thing in the world to do. That said, my finger is my problem. You're responsible for
your own shop safety. If it looks bad or feels bad for you, definitely don't do it. Now that most of the
material has been removed from all the valleys that I cut with the rotary chisel, it's time to
start thinking about the final patterns that I'm going to wind up putting on this thing.
This is a cup burr. It's used by jewelers, apparently, to round the end of wire. What they don't tell you
in the user manual is that you can strap it into a Fordham rotary tool and use it to burn the
absolute you-know-what out of a nice piece of mahogany. This was the first pass that I made with
this new bigger set of cup burrs that I had, and as you can see, it was pretty smoky. So immediately,
I reached for my respirator, a fan, and started my dust collection and backup electrostatic
filtration systems. It smells nice, but I don't think you want to breathe a whole lot of this
smoke. As far as design, all I'm looking to do here is space out the bigger dots that I'm going
to make here. So basically, every small subsection that I made using the rotary chisel and the rotary
tool is getting its own big dot or two or maybe three. As this piece progresses, my plan is to
slowly fill in the most elevated sections of the bowl with the biggest cup burrs that I have in my
possession, and then as we get down into the valleys, I want to start using the smaller and
smaller cup burrs to get sort of a finer detailed effect. Yet another safety note, one thing to know
about these cup burrs is that after you've been using them for a while, they get absolutely
flesh-meltingly hot. Don't ask me how I know. So I've been using a nice pair of pliers to swap
these things in and out. This kind of embellishment is sort of stream of consciousness. I don't map
out every cut that I make before I make it. Really, I'm just looking at the piece and trying
to feel out where I think that the next divot should go. All in all, I would estimate that I
put somewhere north of about 10,000 individual cuts into this bowl. I started it sometime in
early November, and I didn't finish it until the last week of December. I'll leave some links in
the description below if you want to pick up your own set of cup burrs and maybe a slightly
upgraded rotary tool. I will say that these do okay in a Dremel, but I think that you want something
with a minimum of about one-third of a horsepower, especially if you're going to try to drive these
bigger burrs. The smaller burrs might do okay on a traditional Dremel, but once you start getting
above like six or seven millimeters, it seems to bog down. Right around here, I think the general idea
of what I'm going for starts to become clear. I'm really trying to cover up all those high spots
with nice big dots and then start working smaller and smaller as I get into the crevices. One of the
bummers about putting things on YouTube is that I can't play music loud in my shop like I used to
while I'm filming. The copyright gods get very angry, and they will strike me down. So the solution
is, when I'm doing repetitive work, to put on a nice set of headphones and put on some groovy
music that I enjoy. This week's selection, Infinite Health by Tycho. Nothing makes the time fly like
mellow, groove-oriented music. Now, the longer these carving sessions started to go on, the more often
I started to wear gloves, and I don't want to make a safety recommendation here to you because I think
that there is a rule about gloves and spinning tools. That said, this spinning tool is pretty
small, and I think I could stop it with a bare hand if I really had to. To me, this came down to
a trade-off between the ultimate platinum level of safety and the small bits of nearly glowing
hot redwood that were constantly flying into my fingers as I was doing this. Clearly, I chose
comfort. You can see how much charred wood is starting to just get spat out onto the bed of
the lathe. This started to become an issue because it started occluding the spaces that I hadn't
carved yet. It made it difficult for me to tell what I'd actually gone over with the burrs already.
I'm finally starting to get into the point where I'm starting to put little burrs into the alleyways
in between the bigger portions. Now, there is so much less surface area in these alleyways than
there is on the big surface pieces, but the burrs have gotten proportionally smaller, and this is
where the work really starts to drag. I was swapping burrs every 10, 20, 30 minutes when I was on the
bigger size, but once I start to really scale down into the 2, 3, 4 millimeter range, the work just
starts to freeze. The complete work of each one of these burrs takes 2 to 3 hours. I've slowed this
portion down to regular speed just so you can see sort of what I'm trying to do. I'm trying to hunt
the little spaces in between the other dots. It's not just the actual burring that takes time, it's
the hunting in between as well. I'm trying to find spots where the entire burr can fit without cutting
anything else on its way through. I'm also trying to slowly fill in the gaps between all of the
really big dots. They leave these interesting little sculpted triangles in between them, and I'm
trying to make sure that I get a burr into each and every one. Every couple of minutes, I have to
stop and scrub this thing down with a nylon brush just to make sure that I'm getting all the burnt
wood and carbon out of the way. Otherwise, I can't tell what I've already carved. Each time I scrub it
though, I get another good look at where I actually am in the grand scheme of the bowl. From here, I
think things are finally starting to really come together. If I were to estimate the total amount
of time that I spent actually with my hands on the Fordham grinding these burrs into the wood, I
think it would have to be north of 20 hours. Probably fewer than 30, but probably more than 20.
As you can tell in the video, I go through several outfit changes, a couple of mood changes. I fully
put it down for like a week because I was just kind of done with the project. That said, when I
hit this point, I was absolutely elated. This is one of those textures that doesn't make a lot of
until you get right up to the end. It's sort of like a good movie. It just kind of comes together
in the last few minutes. I gave it another good brushing, but here you can see me sort of waffling
on what I want to do with the bottom of this thing. I wound up leaving it in the final piece
just so that people could tell that this was turned instead of carved. I might change it later,
but I'm okay with it for now. Now, since the burrs did an incomplete job of scorching the wood,
I'm going to start adding some India ink to the outside to get a really nice,
rich black color. I'm applying it with these little foam brushes, basically just trying to
sort of dab my way in between all these little dots. The India ink that I'm using is Speedball
brand, and it has shellac in it, so this is also going to help seal up the wood on the outside.
I can't remember the last time that I willingly colored a piece. I just don't tend to work with
a lot of color, but my wife's favorite colors are black and gold, and I decided, well,
she's a pretty smart lady since she married me. She must be onto something. So, this is the point
where I decided that this entire outside was going to be black with gold accents. As I'm dabbing all
of this India ink on, I'm trying to avoid the center for two reasons. One, I don't want to
dye anything that goes below the wood, and two, I really haven't decided what I'm going to do with
the actual inside of this bowl yet. Just in terms of contrast, the way that I'm thinking about it
at this point as I'm putting the dye on is that it either needs to be an absolutely perfectly
smooth hemisphere, or I need to figure out something to do to the inside to make it stand
out against the texture on the outside. That's when this visual theme of chaos versus order
starts to become a little bit more apparent. Now, I can either leave that perfect hemisphere, or
I can use the rose engine that I have on the other side of my shop. Which one do you think I chose?
Now, I don't want to cut anything too deep, so I'm using the D30 rosette, which has one of the
shallowest amplitudes of any of the rosettes that I own. That way, I'm not making big mechanical
changes to the inside of the bowl necessarily. I'm just putting a little bit of order, a little bit
of structured patterning on the inside to help contrast with the randomness of the outside.
Even though I'm fairly confident in my rose engine, this was really scary. I had so many
hours into the outside of this bowl that putting it near anything that was spinning and cutting was
pretty dicey. I'm not sure that fortune actually favors the bold, but I do know that people who
do reckless things learn a lot faster than people who play it safe. This combination had learning
experience written all over it. Thankfully, the bowl survived without too much drama, and I was
able to take it back over to my regular lathe. Now, finishing starts to get a little bit interesting
here, because I have two completely different surfaces. I decided that at the very least, I
wanted to protect the interior rose engine bowl, so I hit it with a little bit of this 50-50 orange
oil and tongue oil mixture. Mostly, I just wanted to protect the inside from whatever dumb idea I
was sure to have next about the outside. I'm also trying to be careful not to get any of this
mixture on the India ink on the outside, because this mixture contains a solvent. Here's a decent
look at where we are at this stage in the project, and I think it's starting to come together. I have
decided to add one more element, though, and that is to gild just a small handful of these bigger
dots. Like I said, my wife loves black and gold, and I think the contrast is also going to be pretty
interesting. This is a pretty simple gilding kit from Amazon. I think it cost me about 14 bucks,
and basically the deal is you put some of this adhesive on wherever you want the gilding to go,
and then you let it stand for 30 minutes, and then you kind of slap this fake gold leaf on top of it.
What you're going to see in the next few minutes is a guy who does not know what he's doing with
any of this gold leaf. I thought that the adhesion would be a little more consistent, but the leaf
kept breaking up on me, so I would just take flakes of it and move it over to other areas
with naked adhesive. Shockingly, this actually seemed to work okay. The part that I didn't
anticipate was that once I started brushing this, it was going to completely fill the air
with these imitation gold flakes, so I wound up having to turn on my dust collector.
Gilding seems like such a classy work, but make no mistake, all you're doing is fabricating your
own glitter. I did the gilding in segments because I was so afraid to accidentally dip my thumb in
any of the adhesive anywhere else on the bowl, so I basically would just turn it by about a third
every single time and do the exterior that was facing up. Unfortunately, my technique did not
improve by much over the 90 or so minutes that I tried this, so I just started using more and more
this gold leaf to make sure that I got complete coverage wherever I had put the adhesive previously.
I suppose the fun of this project is that each stage came with its own sort of panic,
panic about maybe destroying something that I had put so many hours into already.
That said, once you lay the adhesive on or once you mount it on the rose engine, there really isn't
any choice but to just go for it. In effect, you've already jumped, so you might as well try to fly.
I will recommend before you do any gilding of your own that you sweep your shop just to make
sure that this stuff doesn't get mixed in with your wood shavings. I don't know if you use them
for anything else, but I'm positive this stuff won't smell good when it burns.
After one big final brushing session, I wanted to make sure that I got as much of this gold leaf
out of the way as I possibly could, so I also picked up my air duster just to see if I could
flake off any little extra bits that weren't coming off with the brush. After I removed all
the excess, I added a little bit of this water-based varnish to the top of each of the pieces of gilding.
This was just what the instructions said to do, but I thought it made sense for me because I was
already planning on adding some oil to the outside of this piece to try to deepen that black color a
little bit. For my finish today, I'm going to be using walrus oil pure tung oil. I selected this
finish because it doesn't have any solvents in it. I couldn't have anything peeling up the india ink.
My application method is going to look pretty silly in a second. I'm going to use one of those
little foam brushes just to sort of dab it in and try to get it into all the crevices.
I'm trying not to flood any of the areas or rub any of them because I'm still not sure as I'm
doing this if any of the india ink is going to come up with the oil. Lucky for me, the ink seems
incredibly stable. What I wind up doing is basically just completely flooding the surface
using the foam brushes. Somewhere in here I start to realize that I'm going to wind up with like four
to five times as much tung oil as I actually need to have on this piece. So the first thing I think
is let's get some shop towels, bundle them up, make them nice and soft, and I'll just sort of
dab the oil out. And that just didn't go that well. Lucky for me, I had the kind of brain wave you can
only have if you've only gone to two semesters of community college. Spin the oil off. Shockingly,
this kind of worked. I actually managed to remove a lot of the excess oil. I did remember to put a
silicone sheet on the bed of my lathe, but the rest of the oil just made a stripe down the center
of my shop, so I spent some time cleaning that up as well. I tried dabbing it again, a little bit
underwhelming results. Then I thought, hey, let's blow it off. Then I thought, let's spin it and
blow it off. This was the last great idea I'd have with this piece. Let's see how it turned out.
Thanks for sticking around. I'm Brad, this is Q Branch Woodworks,
and if you've enjoyed this video, please consider subscribing.