How a Hybrid Car Works: Toyota 3rd Generation Prius Teardown

The Engine Story
7 followers
Today we're going to be taking a look inside the Toyota Prius 3rd generation hybrid system
to see what's inside and how it works.
And at the heart of the system is this power inverter which is going to take battery voltage
from the back of the car and use that to control the motors inside the transmission.
I'm already taking apart the eCVT transmission so if you want to see more on how that works
make sure you stay tuned for that video.
Now for the 3rd gen Prius they definitely made this a lot smaller and lighter.
Here you've got your coolant inlet and your outlet.
At the back here is where you've got your outputs.
These are for MG1 and MG2 as well as your DC power input.
You've also got power output that goes to the AC compressor.
So let's take this thing apart and see how it works.
First off I'm going to take off these connector covers.
And when you remove that.
Here you can see where I've disconnected those big high voltage wires to get this out of
the vehicle.
Now these here are the connections for the computer and battery control.
It's got a bit of weather sealing on it.
Next I'm going to remove all the 10mm bolts that go around the top half of this casing
here.
The top half seems pretty sealed so I'm actually going to start removing the oil pan, or the
bottom half.
Cool!
It's starting to pry up on the case around here but it's not coming off.
I'm going to go ahead and remove this fusible link.
That's what the fuse looks like.
Behind the secret cover there's 2 more bolts here that carry bus bars.
There's actually another compartment here with 3 bus bars.
Alright, now I can lift off the lid.
Alright, taking a look at this inverter you can see we've got the casing here.
There's actually a little kill switch inside of here that attaches to the current sensor
on the body here.
Taking a look underneath the inverter cover here we've got a giant capacitor.
Taking a look inside the inverter itself we have this top board over here which acts like
the computer that's going to control these motor generators.
Now on the Gen 3 Prius things are a lot more compact and there's no onboard inverter for
the AC compressor.
Instead that's just done onboard the AC compressor itself.
First I'm going to remove the current sensor which is this bar going across here.
Alright, now I can disconnect that.
And here you can see the hookups for MG1 and MG2 using these very large bus bars because
they carry a lot of current.
And inside of here with these loops we have the current sensors which connect to these
wires over here.
That tells the computer how much current is actually being sent so it can control the
motor using closed loop control circuits.
Next up we come to the motor controller and it's got a bunch of these little connectors
here that I'm going to remove.
And then we can pop this board off.
So looking at the control board circuitry you can see it's got our main interface.
It's going to go out to the vehicle's CAN bus system to talk to things like your powertrain
control module as well as the battery controller at the back of the vehicle.
You've got multiple ICs on here and of course your inputs for your two current sensors.
Taking a look at the next main board this is kind of our IPM or transistor module.
I've also got to take out the DC connections that go down to the DC to DC converter underneath.
Now this is going to be really messy because it's got a bunch of thermal paste underneath
here.
Taking a look inside of this power inverter here you can see we've got a nice chunk of
aluminum on the back of it and that's to transfer and dissipate heat away from the transistors
that are switching inside of there.
We've got coolant coming in and coolant coming out to help cool that down and send it off
to the radiator.
Now this piece also has got this thermal paste on it to cool down the DC to DC converter.
You can see how things are a lot more light and compact whereas the second generation
used the cooling system going through the casing itself and then the IGBTs would paste
on top of that.
But you've also got to replace this as an entire unit if something does go wrong.
Now in order for me to not make too much mess I've got my daughter's old onesie here.
I'm just going to wipe up some of that thermal paste.
Now inside of here you've got all the control circuitry for the integrated gate bipolar
transistors which reside underneath here.
Now unfortunately in order to get this off humanely you need to desolder all of these
pins over here and over on this side which is not exactly possible because they don't
have a hot air station for an oven.
Wait a second, I've got my brother's old oven over here.
Don't you just wish they made a 240 volt extension cord that would reach all the way to the house?
I mean I'm sure his wife wouldn't mind but maybe we'll find another way.
Alright I guess I'll just use the snips.
These snips are too slow so I'm just going to move in with my other snipping tool here.
I'm going to take these couple of screws apart here.
Now I can pop off the cover here and you can see the IGBTs.
Yep you heard me right we're not talking about LGBT here we're talking about IGBT which stands
for integrated gate bipolar transistors.
Taking a look at the transistors here there's like 22 of them.
Now you can see they're kind of paired off here and that's because they're running parallel
because you've got so much current going through here.
And the transistors are basically like switches so they're going to switch on and off that
DC current in order to form a waveform and then you phase them 120 degrees apart and
that's how you get your 3 phase UV and W for MG2 here and MG1 respective.
Now this gel is like a thermal insulator but it also protects these from getting damaged
and that allows most of the heat to escape down the bottom through this heat transfer
over here.
Compared to the 2nd generation Prius we had our boost converters as well as our DC to
DC converter separated from the IGBT unit and this here was just a plate with the cooling
system embedded on the body itself.
Now if you were to open this cooling system you were to see a bunch of fins inside of
here as the coolant runs back and forth.
You can see that on the 2nd gen Prius and this one it's all laminated over and you can't
really open it up.
Now also integrated into this unit are the diodes and what they do is the opposite of
the transistors is that they try to rectify the current that's coming in through here
as alternating current when you're doing regenerative braking and sending that out to the capacitor
to get smoothed back into DC to charge the battery.
So essentially it's DC in on this side and AC out on this side and each one of the switches
are controlled through these connectors.
Alright taking a look at what exactly goes on inside of this inverter we've got 201 volts
DC that comes from the high voltage battery in the trunk and that comes into the inverter
first of the battery boost circuit.
That's where you've got the coil and the capacitor that can boost you up to about 650 volts.
That voltage is then going to go over to the gate drive circuit and the IGBT transistors
to create this waveform over here.
Now if you create 3 of those waveforms 120 degrees apart then you have 3 phase AC current
that can then drive the motors inside the transmission to turn the wheel.
Now as you're slowing down you want to recapture some of that kinetic energy to charge the
batteries so your motors now turn into generators.
That 3 phase current is then going to be fed back into the inverter and goes to the diodes
to get rectified.
So it turns that full sine wave into this ripple that you see over here and then it
sends it out to the smoothing capacitor to smoothen out those ripples so you have pretty
much DC current which can then feed the battery and charge it back up.
Of course this also works if you're just sitting at a stoplight and your engine is running
that can also act as a generator and rectify current to charge the battery.
Next up let's flip this over and take a look at the bottom of this unit here.
Now let's take a look at the DC to DC converter.
Essentially we're going to take 201 volts DC from the hybrid battery pack and then transfer
that using the IGBTs to alternating current.
Send it through this transformer over here which is a center tap transformer.
That's going to bring it down to 14 volts and then rectify that again and transfer it
back to DC in order to safely use it to charge a low voltage battery.
Alright I'm going to remove lots of these Phillips screws here starting with the high
voltage.
I'm going to start removing all the circuit board screws, the 10s here.
Alright I'm going to remove this piece over here and then I can slide this board off.
It's got a bus over there.
Over here we've got another one of these.
Alright I'm going to remove this bus bar here.
The transformer itself feels like it's held on with thermal paste.
Yeah, it's pretty dirty.
Over here is a connection where the 14 volts goes out and of course it gets grounded to
the chassis of the car.
That goes to the fuse box and of course the battery.
Now this is as far as I can unbolt things because the diodes that sit inside of here
are actually screwed down to the casing and then soldered on top of here.
Try out this desoldering tool.
Okay, maybe I've got it out.
And you can see the three transistors or diodes that are sitting on top of this.
They're screwed on and they've got some kind of a thermal paper on here as well.
So it appears these are the three transistors that are going to turn it into AC and then
these are the diodes that are going to rectify it and turn it back into direct current.
And nothing too interesting on the control board here, just a couple more relays.
Now also on the housing here we've got two smaller capacitors.
This one here is a film capacitor for 0.6 microfarad.
This one here is also a film capacitor for 0.562 microfarad.
And both of these little capacitors actually hook up to the large capacitor over on the
sides here.
Here's a look at the transformer.
Essentially, it's going to step down your 201 volts with these little wires coming in
here to 14 volts which is going to come through this bus bar.
Now voltage and current are proportional when you step down voltage.
The current is going to significantly increase and that's why you need this bus bar to handle
it and not some thin wires.
This of course is alternating current so the 14 volts is going to have to get rectified
before being sent to the battery.
Now let's talk about the elephant in the room and that's this giant inductor for the boost
circuit.
Essentially, in order to boost up the voltage, you run current through here.
It's going to create a magnetic field.
Now you combine that in parallel with the capacitor to form an RC circuit.
When you control that with transistors, switching them on and off, you can essentially add up
the voltage coming from the inductor and the capacitor to change it from the battery's
201 volts to about 650 volts to turn the electric motors a lot more efficiently.
I'm going to go ahead and remove these wires.
Let's remove this bus bar.
Now this is an inductor.
This will also create heat and that's why it's attached to this plate.
I'm going to have to do a lot of prying here in order to get this out.
So it looks like it's encased in some kind of a plastic resin that really holds it in
there.
Now with the size of this coil, you'd think that it's electromagnetic field, but in effect,
little coils like this that sit nearby.
Let's remove the capacitor now.
I'm going to lift this out into one unit.
Now the main function of this capacitor is to smoothen out those alternating current
waves that are coming from the motor as you're doing regenerative braking before it goes
out to the battery.
Over here you've got a 136 kilo ohm resistor that's across the main two terminals of the
capacitor here.
It's really just there as a safety precaution so that by the time you've opened this thing
up to get down to playing with the capacitor, you're not going to be shocked by the full
650 volts, you'll be shocked by a lot less.
Now this is a lot lighter and smaller than the one I took apart in the second generation
Prius, and I'm not going to cut this apart because last time I did, the acid spewed all
over and started burning up my nose, and I don't want to be flagged by YouTube for dangerous
operation.
As if my angle grinder wasn't dangerous enough.
Taking a look at a more holistic approach at how the inverter plays into the hybrid
system, you've got a high voltage battery at the back, as well as our 12 volt auxiliary
battery to run things like your electronics, your radio, and accessories.
The high voltage is going to come into the drive circuit through your transistors and
that's ultimately going to feed MG1 and MG2, which is inside the transmission through a
power split device.
If you want to learn more about how eCVTs work, check out my next video.
Now eventually some of that power is going to be captured and rectified through diodes,
and then sent back to charge the high voltage battery when you're doing regenerative braking.
Now in addition to that, some of that high voltage is going to be converted back down
to charge your 12 volt battery, because you don't have a typical alternator in a hybrid
car.
And some of that juice is also going to power the AC inverter, which on the third gen Prius
is actually in the AC compressor itself.
And then of course the inverter interfaces with other modules, such as the battery computer
and the power train control module.
And then there are physical things like the water pump, cooling tank, and radiator circuit,
which feeds this entire inverter and transmission assembly to keep it cool, separate from the
engine.
So here we've got the high voltage battery pack located in the trunk over here.
Now the battery pack itself is made up of multiple different cells, and that's going
to add up to your high voltage.
Now over here we have the ventilating fan with its associated duct board that will be
on top of here.
Now taking a peek inside of there, you can see there's the contacting relays and the
associated electronics that control this battery pack.
At the top there are the two terminals that are going to go to the inverter at the front
of the vehicle.
Now at the back here, these two orange cables are going to lead up to the safety switch,
which plugs in over here, and that essentially is going to turn off this battery from working,
so it's safe to handle.
Inside this corner here we have the connections for the 12 volt battery, which runs all of
the CAN bus and electronics in this car.
And that's a look inside the third generation Toyota hybrid system and how it works.
Now I don't have the high voltage battery here for a full teardown.
Now I know this looks pretty complex and you probably questioned the reliability, however
over the past 20 plus years that this technology has been around, it's proven itself to be
very reliable.
As a matter of fact, this car had 300,000 kilometers on it, and it was the internal
combustion engine that blew a connecting rod, which is what decommissioned this car, not
any of the electronics.
Make sure you subscribe if you want to see more videos just like this one.
