HOW TO MAKE A PINCH POT

Making ceramics and glass
106 followers
Hey folks!
Today I'm going to teach you how to make a pinch pot.
By now you should have already wedged out a one pound chunk of clay.
Now you're going to slap and wad it into a perfectly round ball.
Next, take your thumb and puncture down into the ball of clay, but be careful not to perforate
the base.
You're going to need that.
If we look at the inside profile, this is what you would see.
As I pinch the clay from the bottom to the top, and top to bottom, it's going to eventually
thin out.
As I pinch around the inside with one hand, the mouth will get wider, and I'll be able
to fit two thumbs on the inside.
As I apply pinching pressure from top to bottom, and bottom to top, the pot will expand and
eventually become thinner.
I want you to notice how I'm using the table's surface to support the side profile of the
pinch pot.
This allows me to keep it sturdy as I pinch, and prevents it from flaring out too wide.
A bending wheel would be preferable here, but it's likely that not everyone will be
This is the basic pinching motion that I'm using when I'm pinching the pinch pots.
Notice that I'm alternating my hands as I'm pinching.
This allows me to support the pinch pot with one hand while I'm pinching with the other,
and vice versa.
If I look at a side profile of the stage that I'm at right now, you can see the walls are
starting to thin out.
Thinness is kind of the end goal here, because if the walls are thick, we're going to end
up with a heavy object, and we don't want a door stopper.
We want a fully functional utilitarian object.
So down at the very bottom of the pinch pot, there's some thick clay that I couldn't quite
reach with my thumbs.
So I'm supporting the base of the pinch pot with the palm of my hand in a cup-like motion,
and just kind of compressing down with my fingers of my right hand.
This is going to kind of make the pinch pot conical, or cone-shaped down at the very bottom,
but that can be pretty easily fixed by tapping the base on the table, or adding a foot ring.
Alright, now you can see the walls are adequately thinned out, so now I can take this time and
shape my pinch pot, trim the rim, and kind of smooth out the surface so that it looks
a lot nicer.
If while you're making your pinch pot you're noticing the rim cracking, simply just add
a little bit of water to the rim and smooth it out.
Just a dab will do.
It would also be a good idea to kind of gently compress down on the rim, and that'll really
make sure that the clay platelets fuse together so that you can avoid more cracking in the future.
So now I'm going to trim the rim of the pinch pot level.
What you're going to need to do first is center the pinch pot on the banding wheel, or a kick
wheel, or any wheel for that matter, and with a needle tool or a scalpel, draw a line with
a steady hand at the very top where you intend to cut.
You might need to make a couple pass-throughs, but gently lift off the excess amount that
has been cut away, and then with a sponge or a chamois, just smooth out the rim.
After you're finished on day one, you're going to want to turn your pinch pot upside down
and scribe your name and period number on the bottom of the pinch pot.
This is so you don't confuse it with anyone else's.
Gently put it into a plastic bag, no need to spray it at this point, and cover it up
completely.
Set it on a wear board, and then gently slide it into your cubby space.
So since we're still on the topic of day one, let's talk about a couple of things that could
go wrong.
Let's say your pinch pot isn't looking much like a pot at all.
Let's say that it's flaring out too wide, or it's extremely asymmetrical, what you could
do is take your clay and dunk it back into the water bucket that's at your table.
Smash it in between your fingers multiple times, you could even try and re-wedge it,
but ultimately just work it back to the normal pliable plastic consistency of the clay that
you originally got out of the bin.
Once that's done, the clay is ready to use again.
Also be careful with the way that you handle your pinch pot.
You don't want to aggressively tap it on the table, drop it, or mishandle it in any way
that misshapes the overall form.
Otherwise that might likely result in a restart, and that's never fun.
If I'm wanting to alter the form in any way, that's going to come from the pressure that
I put in certain areas of the pinch pot.
So the square that I'm making right here, I've pinched the corners and I'm kind of pushing
up against the inside base, or the wall excuse me, with the fingers.
So pressure, counter pressure.
Once I've pinched to make that kind of squared off shape, then I'm going to take a paddle
and kind of just paddle up the sides to assist with getting that squared off form.
Also a trimming stick or a flat ribbed tool will help kind of smooth out the flattened
surfaces, or the squared off sides that I'm trying to achieve.
It takes a lot of work to get, but eventually it all comes through.
Alrighty so on day two, remove your pinch pot from the bag and check to make sure it's
leather hard.
Leather hard is when the clay is no longer plastic and durable enough to withstand the
pressure you put on it.
It shouldn't bend or flex very much at all.
So what I'm doing right here, and one of the ironies of working with clay is that you have
to sometimes rough up the surface in order to smooth it out.
That's very applicable in this situation.
If I want to eliminate my finger marks and indentations, I need to score the surface
with a serrated metal rib, likely multiple times to achieve the desired effect.
Then I need to smooth out the surface in a waxing motion with a dampened sponge.
Yes, this will make the surface a little gruggy, but then I can burnish it down with the flat
side of the rib, or the back side of a spoon.
Alrighty so it looks like I'm done here.
I'm just going to place this upside down on the banding wheel and spin it a few times
to make sure that I've achieved the symmetry that I was looking for, all through shaving
and paddling.
So after achieving symmetry in my shape and smoothing it out, I'm going to add an elaborate
foot ring to the bottom of this pot.
To do so, I'm going to place a small coil by slipping and scoring it into place.
Scoring is the action of scratching the surface you intend to add clay to.
This allows the platelets to readily interlock together.
Slip is like the bonding agent that glues the clay together.
These two actions assure that your two pieces of clay will stick together.
I'm going to continue to pinch this ring until it gets a little wider.
Basically just think about making it another pinch pot underneath your first pinch pot.
So already I've pinched the foot, thinned it, trimmed it, and smoothed it out.
I'm going to take a rasping tool and score the area where I attached the ring, and then
I'm going to smooth it out with a sponge for a seamless transition from the body to the
foot.
Next, I'm going to add a handle to the pinch pot.
Not that it needs one, but I feel like it'll suit the form and will likely be more aesthetic
than utility.
Just like when I attached the foot ring, I'm going to slip and score the handle to the
side profile to assure that it sticks well on the pot.
And that, my friends, is how you make a pinch pot.
Thanks for watching.
